Download  Print this page
   
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467

Advertisement

• Make sure not to place the unit too far from the
wireless LAN router.
• Check your wireless LAN connection
environment. You cannot use CH 12 and 13 (for
European customers).
• If the electric wave is crossed with other wireless
LAN waves, change the wireless channel.
• Check for obstacles (metallic wall, etc.) installed
between the wireless access point and the unit.
These obstacles shorten the wave's reach length.
• When using the PARTY MODE, using
IEEE802.11g (wireless)/100BASE-TX (wired)
for LAN connection is suggested.
If the unit still does not operate
properly after performing the
above measures, reset the unit
as follows:
While the unit is 'on' (the unit is connected to
an AV system), press RESET on the bottom of
the unit using a fine-tipped tool (e.g. pencil,
etc.).
The unit is reset to the factory settings. You should
set the settings you made.

Messages

If a message appears while using the unit, follow
the procedures below to correct the problem.
Network
Cannot Play
• Start up M-crew Server Ver. 2.5 and click
[ERROR LOG] in the LAUNCHER window, or
right-click the M-crew Server task tray icon* and
select "ERROR LOG VIEWER", then check the
error log.
• The track cannot be played in the following cases:
– Sampling rate is other than 32 kHz, 44.1 kHz,
48 kHz.
– The track is not being streamed by linear PCM.
– The track is other than one channel or two
channel.
– The track sampling bits are other than 16 bits.
– The server status is busy.
Check Net
• Check that the network cable between the unit and
the hub or router is firmly connected.
• Check that the hub or router is turned on.
• Set the wireless LAN router channel to any
channel from CH1 to CH11. For details, refer to
the operation manual of your wireless LAN
router.
• The wireless signal is not strong enough. Move
the unit closer to the wireless access point. If the
unit is already close to the access point, check the
configuration of the access point to ensure that the
access point is sending a signal. Once the changes
have been made to the access point, toggle the
WIRELESS/WIRED selector to reconfigure
setting.
IP Conflict
• Set the IP addresses of the unit and other devices
on the network so that there is no duplication
(page 32).
No Item
• Register the track as instructed by the operation
manual of the connected server.
• Follow the procedure below and reconnect to the
server.
1.
Press MENU.
2.
Select "SERVER?" in the network menu
(page 31), then press ENTER.
3.
Press ./> repeatedly to select the
desired media server, then press ENTER.
GB
35

Advertisement

Chapters

Table of Contents

   Related Manuals for Sony TDM-NC1

Comments to this Manuals

Symbols: 0
Latest comments: