Usb2.0 high-speed, 1 mic-in / 1 instrument-in, 2 out professional recording usb interface with smart phone connectivity for live streaming application (29 pages)
Page 1
4-In / 4-Out Recording USB Interface with MIDI & S/PDIF I/O COMP DIRECT N16549...
Page 2
Important Safety Instructions Read all manufacturer's warnings and instructions 2. Do not use this apparatus near water. 3. Clean only with dry cloth. 4. Do not block any ventilation openings and do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Contents Introduction What's in the package Features Front Panel Layout Rear Panel Layout Driver Installation Control Panel 8-10 11-12 Hardware Connections Minimum System Requirements Stacking the UtrackPro Specifications Services...
Introduction Thank you for purchasing the ICON Utrack Pro Digital Audio Interface. In these pages, you'll find a detailed description of all Utrack Pro features, a guided tour through its front and rear panels, step-by-step instructions for its setup and use, and full specifications.
Features COMP DIRECT The ICON Utrack Pro mobile interface audio input and output module offers USB connectivity. Main features include: 4 x 4 analog balanced I/O Dual microphone/instrument preamps with gain controls, LED metering, phantom power and input gain Two analog inputs and four analog outputs on 1/4" TRS jacks S/PDIF I/O on RCA coaxial connectors Supports sampling rates from 44.1Hz to 192KHz...
Front Panel Layout COMP DIRECT MIC/INST INPUTS Unbalanced Instrument and MIC level inputs. These hybrid connectors will accept a standard three-pin XLR plug or a 1/4" TS connector. CLIP LED When lit, this LED indicates clipping input level at the associated MIC/INST input.
S/PDIF COAXIAL IN AND OUT CONNECTORS S/PDIF digital input and output on coaxial RCA connectors. The digital input is selected via the Utrack Pro's control panel, while the digital output will be sent to the coaxial . MIDI IN AND MIDI OUT CONNECTORS MIDI input and output on standard 5-pin DIN connectors.
Driver Installation Please follow the below procedures step-by-step to install your Utrack Pro and its driver. Turn on your computer Note: Do not connect the Utrack Pro to your computer yet Insert Driver CD to your CD-Rom After you have insert the provided...
Page 9
Diagram5. Then click "Next". Diagram 5 Connect your Utrack Pro Now, connect the Utrack Pro to your computer's USB port and turn on its power switch and click "Finish". Notes: Utrack Pro only support USB 2.0. Your computer must have an USB2.0 port.
Page 10
Click "Finish" Diagram 11 Launch the Utrack Pro Control Panel You may click the Utrack logo on the system tray to luanch the Utrack Pro Contrl Panel (Page 8). Diagram 12 Note: For the latest driver updates please check www.icon-global.com...
Showing the S/PDIF device signal staus. S/PDIF Pass Through "Tick" the box if you wanted S/PDIF signal pass through WDM Sound Device Configuration As Utrack Pro is a 4x4 I/O interface, you Diagram 4 should select "Stereo" for this setting.
Page 12
Control Panel (Continues) Hardware Inputs Mixer Matrix Fader Hardware Inputs Ch1,2,3,4 & S/PDIF Level Metering Showing the input level for the hardware input channel. Hardware Onputs Ch1,2,3,4 & S/PDIF Level Metering Showing the output level for the hardware output channel. Link Switch Switch to adjust both Channels simutaneously Mute Switch...
Page 13
Control Panel (Continues) Software Inputs Mixer Matrix Fader Software Inputs Ch1,2,3,4 & S/PDIF Level Metering Showing the input level for the software input channel. Software Onputs Ch1,2,3,4 & S/PDIF Level Metering Showing the output level for the software output channel. Link Switch Switch to adjust both Channels simutaneously Mute Switch...
Connect the Utrack Pro's outputs to your amplifier, powered monitors or surround system. For two-channel stereo operation, the default outputs are channels 1 and 2. However, you may change this in the Utrack Pro control panel at your desire. For multi-channel surround output, connect up to four powered monitors to the Utrack Pro's four analog outputs.
Microsoft. On the Mac, the Utrack Pro is supported under MacOS 9.2 or later, and Mac OSX version 10.1.5 or later. Earlier versions of Mac operating systems are not supported.
Stacking the Utrack Pro You can stack one Utrack Pro or any other ICON Reo Series gears on top of each other by simply lining up the bumpers. COMP DIRECT COMP DIRECT ReoMidi 4 MIDI IN MIDI OUT CH 1...
ICON is not responsible for any damage that occurs due to non-factory packing. 3. Contact your ICON dealer or if none is available, contact the nearest ICON distributor or regional office to obtain a return authorization. If applicable, shipping instructions will be provided by the dealer or from ICON.
Need help?
Do you have a question about the Utrack Pro and is the answer not in the manual?
Questions and answers