Transporting The Printer; Related Documentation - Epson Stylus Pro 5000 User Manual

3. Press the button repeatedly until the appropriate H
Reset
ink out light comes on.
The following list shows the Ink Out lights corresponding
to each numbered pattern:
Pattern #1: black H ink out light on
Pattern #2: cyan H ink out light on
Pattern #3: magenta H ink out light on
Pattern #4: yellow H ink out light on
4. Press the button to enter your selection.
Eject
The printer prints seven patterns, similar to the ones below.
The paper tray lights turn on and the P
lower paper tray lights flash.
5. Determine which set of lines on the printed sheet is
vertically aligned, and select the corresponding number
using the and
Reset Eject
Press the button to move the selection to the right and
Eject
press the button to move it to the left. Press the
Reset
buttons repeatedly until the appropriate H
come on or flash to select the vertically aligned pattern.
Ink out light indicators for vertically aligned pattern
#1 #2 #3 #4
black black cyan cyan
on flashing on flashing
magenta
flashing
For example, to select the correct alignment pattern from
the sample, press the
Eject
and magenta ink out lights start flashing.
6. Press the button to enter your selection.
Cleaning
The printer returns to the print head alignment mode.
7. If other numbered patterns in step 1 are misaligned, repeat
steps 2 through 6.
8. When you're finished aligning the print head, press the
button to save the alignment setting and turn
P Operate
off the printer.
and [
Operate
buttons and the table below.
light(s)
Ink Out
#5 #6 #7
magenta yellow yellow
on flashing on
or button until the cyan
Reset

Transporting the Printer

If you need to ship your printer, you must prepare it for
transportation and repack it in the original box. You must also
remove the ink cartridges, to avoid the possibility of ink
leakage. However, if you are moving the printer only a short
distance, for example, from one table to another, you don't
need to remove the cartridges. Be sure to keep the printer level
when you move it.
To transport the printer:
1. Turn on the printer and remove any paper in the trays.
Press the button to eject any paper that has been fed
Eject
into the printer.
2. Turn off the printer and make sure the print head is in the
home (far right) position.
If it's not, turn the printer back on, wait until the head stops
moving and is in the home position, then turn off the
printer. After you turn it off, the P
for a while. Don't unplug the printer until the light goes off.
3. Remove all four of the ink cartridges and store them in
separate, resealable plastic bags. Close the ink cartridge
clamps and compartment covers.
4. Unplug the power cord from the electrical outlet; then
disconnect the RIP interface cable from the printer.
5. Remove the standard paper tray. If the optional lower paper
cassette is installed, remove the lower tray.
6. Insert the protective materials you removed when you
unpacked the printer.
7. If the optional paper cassette is installed, unscrew it and lift
the printer off of the cassette.
8. Repack the printer, paper trays, power cord, and any other
parts in the original boxes.

Related Documentation

TM-STYPRO5000 EPSON Stylus Pro 5000 Service Manual
PL-STYPRO5000
CPD-6201
CPD-6202
10016180
10016194
10016187
10016208
11/98
EPSON Stylus Pro 5000
Operate
EPSON Stylus Pro 5000 Parts Price List
EPSON Stylus Pro 5000 Printer Guide
EPSON Stylus Pro 5000 Read This First
Roadmap
RIP Station 5000 Setup Guide
RIP Station 5000 User Guide
RIP Station 5000 Administrator Guide
RIP Station 5000 Color Printing Guide
RIP Station 5000 Server Installation and
Service Guide
EPSON Stylus Pro 5000
light may flash
- 11