Table of Contents
Advertisement
Quick Links
This user's guide describes the characteristics, operation, and use of the TMP007 evaluation module. This
user's guide discusses how to set up and configure the software and hardware, and reviews various
aspects of the program operation. Throughout this document, the terms evaluation board, evaluation
module, TMP007 test board, and EVM are synonymous with TMP007EVM.
1
2
3
Hardware Overview
4
TMP007EVM Software
1
Hardware Included with TMP007EVM Kit
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Control Page: Coefficient Controls Page
20
Programmers Page
Microsoft, Windows are registered trademarks of Microsoft Corporation.
SPI is a trademark of Motorola.
All other trademarks are the property of their respective owners.
SBOU137A - May 2014 - Revised December 2014
Submit Documentation Feedback
Contents
..........................................................................
.............................................................................................
..........................................................................................................
......................................................................................................
List of Figures
................................................................................
.............................................................................................
............................................................................................
..............................................................................................
..................................................................................
..............................................................................
..................................................................................
...................................................................................
...................................................................................................
..............................................................................................
.......................................................................................................
.....................................................................................
....................................................................................
............................................................................
.........................................................................................
.............................................................................................
..............................................................................
................................................................................
........................................................................................................
Copyright © 2014, Texas Instruments Incorporated
SBOU137A - May 2014 - Revised December 2014
TMP007EVM User's Guide
...................................................................
TMP007EVM User's Guide
User's Guide
2
3
5
6
2
3
4
5
6
6
7
8
8
9
9
10
11
12
12
13
14
16
17
18
1
Advertisement
Table of Contents
Related Manuals for Texas Instruments TMP007EVM
Summary of Contents for Texas Instruments TMP007EVM
-
Page 1: Table Of Contents
Throughout this document, the terms evaluation board, evaluation module, TMP007 test board, and EVM are synonymous with TMP007EVM. Contents ................ -
Page 2: Introduction To The Tmp007 And Tmp007Evm
Table 1. TMP007EVM Kit Contents Item Quantity TMP007 test board SM-USB-DIG board Figure 1. Hardware Included with TMP007EVM Kit TMP007EVM User's Guide SBOU137A – May 2014 – Revised December 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated... -
Page 3: Tmp007Evm Hardware Setup
SM-USB-DIG over a USB connection. The SM-USB-DIG translates USB commands from the computer into power, I C, SPI™, and general-purpose input/output (GPIO) commands for the TMP007 test board. Note that the TMP007EVM does not require any additional components to operate. Figure 2. TMP007EVM Hardware Setup SBOU137A –... -
Page 4: Tmp007Evm Hardware Setup
DVDD or V+. Resistors R1 and R2 are 0-Ω resistors that ground the ADDR0 and ADDR1 pins, hence the I2C device address for the TMP007EVM is 80h. The TMP007 ALERT signal is connected to an LED light to visually demonstrate functionality. -
Page 5: Typical Hardware Connection
Hardware Overview www.ti.com Hardware Overview If not already assembled, the basic hardware setup for the TMP007EVM involves connecting the TMP007 test board to the SM-USB-DIG and then connecting the SM-USB-DIG to the computer. This section describes the details of this procedure. -
Page 6: Typical Pc Behavior After Connecting Tmp007Evm
The software is available through the TMP007EVM product folder on www.ti.com. To install the software to a computer, download the SBOC441.zip file from www.ti.com, unzip the file, and open the TMP007EVM software folder. Locate and launch the TMP007EVM installation file (setup.exe), as shown in Figure This file is located in the Installer directory. -
Page 7: Tmp007Evm Software Installation Launch
TMP007EVM Software www.ti.com The TMP007EVM software installer file then begins the installation process, as shown in Figure Figure 7. TMP007EVM Software Installation Launch Follow the prompts shown in Figure 8 Figure 12 to install the TMP007EVM GUI software. SBOU137A – May 2014 – Revised December 2014... -
Page 8: Gui Software And Internal Use License
TMP007EVM Software www.ti.com Figure 8. GUI Software and Internal Use License Figure 9. National Instruments Software License TMP007EVM User's Guide SBOU137A – May 2014 – Revised December 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated... -
Page 9: Start Installation Prompts
TMP007EVM Software www.ti.com Figure 10. Start Installation Prompts Figure 11. Software Installation Process SBOU137A – May 2014 – Revised December 2014 TMP007EVM User's Guide Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated... -
Page 10: Installation Complete
TMP007EVM Software www.ti.com Figure 12. Installation Complete The TMP007EVM GUI software is now installed. TMP007EVM User's Guide SBOU137A – May 2014 – Revised December 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated... -
Page 11: Gui Software Default Configuration
With the TMP007EVM properly connected (see Figure 5), launch the EVM GUI software from the Start menu. This menu is located in a folder titled TMP007EVM under Program Files. The software launches with a screen similar to that shown in Figure Figure 13. -
Page 12: Gui Uncheck Simulate Configuration
If an error message appears when the TMP007EVM GUI software is launched, disconnect all TMP007EVM kit components and repeat the hardware assembly and connection instructions. Next, insert the TMP007EVM hardware into the USB port (if not already done), as explained in the Typical Hardware Connections section. -
Page 13: Main Pages In The Tmp007 Gui
The control panel includes the mode control page, temperature limit controls page, and coefficient controls page. This section describes each page in detail. SBOU137A – May 2014 – Revised December 2014 TMP007EVM User's Guide Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated... -
Page 14: Control Page: Mode Controls
The Device Configuration control box located at the left of the mode Controls page configures the TMP007 conversion mode, conversion time, and transient correction functions. TMP007EVM User's Guide SBOU137A – May 2014 – Revised December 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated... - Page 15 A Data Invalid? button is located at the right of the Mask/Enable Register control box. This button indicates if the calculated object temperature is invalid because of invalid operations in the math processor. SBOU137A – May 2014 – Revised December 2014 TMP007EVM User's Guide Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated...
-
Page 16: Control Page: Temperature Limit Controls
Page. Therefore, the Status Update control (top left corner of Figure 18) is functionally the same as the Status Update control in the Mode Control Page. TMP007EVM User's Guide SBOU137A – May 2014 – Revised December 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated... - Page 17 Memory Bank field. Note that the increments for each memory bank write are as follows: 0, 0, 2, 3, 4, 5, 6, and 7 (note that 1 is missing because of the internal digital design configurations). SBOU137A – May 2014 – Revised December 2014 TMP007EVM User's Guide Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated...
- Page 18 Write Data fields. A specific configuration can be loaded from or saved to a .csv file using the Load Config and Save Config control buttons. Figure 20. Programmers Page TMP007EVM User's Guide SBOU137A – May 2014 – Revised December 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated...
- Page 19 TMP007EVM Software www.ti.com Bill of Materials Table 3 lists the bill of materials for the TMP007EVM. Table 3. TMP007 Test Board Bill of Materials Item Value Ref Des Description Vendor/Mfr Part Number — Printed Circuit Board Texas Instruments EDGE#: 6499073 CAP CER 1.0UF 16V X7R 10% 0603...
- Page 20 NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Revision History SBOU137A – May 2014 – Revised December 2014 Submit Documentation Feedback Copyright © 2014, Texas Instruments Incorporated...
- Page 21 STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein. Acceptance of the EVM is expressly subject to the following terms and conditions.
- Page 22 FCC Interference Statement for Class B EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 23 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 本開発キットは技術基準適合証明を受けておりません。 本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。 1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用 いただく。 2. 実験局の免許を取得後ご使用いただく。 3. 技術基準適合証明を取得後ご使用いただく。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・インスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル 3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page SPACER EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
- Page 24 Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated...
- Page 25 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue.
Need help?
Do you have a question about the TMP007EVM and is the answer not in the manual?
Questions and answers