Advertisement
Operation Guide 5200
• Select a city code in the World Time Mode to display the current time in any
particular time zone around the globe. See the "City Code Table" at the back of this
manual for information about the UTC differential settings that are supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing B (page E-9).
To view the time in another city
In the World Time Mode, press C.
• This will cause the city code of the currently selected World Time City to appear for
about two seconds, followed by the current time in that city.
• Pressing C while a city code is displayed will scroll to the next city code, in the
sequence noted in the "City Code Table" at the back of this manual.
E-20
Alarms
The Alarm Mode lets you configure five daily alarms. You
also can use it to turn the Hourly Time Signal on or off.
• The watch beeps for about 10 seconds when an alarm
time is reached.
• Turning on the Hourly Time Signal causes the watch to
beep on the hour every hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B (page
E-9).
Alarm time
(Hour : Minutes)
E-22
3. Press C to scroll the hour value, until it displays the value you want.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
• The same 12-hour/24-hour format you select for the Timekeeping Mode time
(page E-12) is also applied in the Alarm Mode.
4. After the hour setting is the way you want, press B to move the flashing to the
minutes.
• Press C to scroll the minute value.
5. When the minute setting is the way you want, press B. This will cause "ON" to
flash on the display.
• Press C to toggle the alarm setting between ON and OFF.
C
6. After the setting is the way you want, press A to exit the setting mode.
E-24
3. Press C to toggle the Hourly Time Signal between on and off.
C
4. Press A to exit the setting screen.
To turn off all alarms and the Hourly Time Signal
In the Alarm Mode, hold down C for about three seconds.
• "ALL OFF" will appear on the display indicating all alarms and the Hourly Time
Signal are turned off.
E-26
To measure times with the stopwatch
C
➤
C
Start
Stop
Minute
Seconds
You can use the watch's tachymeter feature to measure the time (within 60 seconds)
that a vehicle takes to run one kilometer (one mile) and then determine the
approximate average speed.
E-28
C
➤
(About 1 second)
Clear
1/100 Seconds
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use C to display the city code
DST indicator
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
• The DST indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
• Note that the Standard Time/Daylight Saving Time
setting affects only the currently displayed city code.
Other city codes are not affected.
• Selecting Daylight Saving Time for the city that is
currently selected as the Home City, will also apply
Daylight Saving Time to the Timekeeping Mode time.
• Note that you cannot switch between Standard Time
and Daylight Saving Time while UTC is selected as the
city code.
To set an alarm time
Alarm number
About 1 second
1. In the Alarm Mode, use C to scroll through the alarm screens until the one whose
time you want to set is displayed.
AL1
AL2
SIG
AL5
• The alarm screens are AL1, AL2, AL3, AL4, and AL5.
2. Hold down A until the hour digits of the current alarm time start to flash. This is the
setting mode.
• Entering the setting mode automatically turns on the displayed alarm.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in.
• Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
• To stop the alarm tone after it starts to sound, press any button.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use C to select the Hourly Time Signal.
2. Hold down A for about three seconds until "ON" flashes on the display. This is the
setting mode.
• Entering the setting mode automatically turns on the Hourly Time Signal.
Stopwatch
The stopwatch lets you measure elapsed times.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Minutes
Stopwatch Mode, which you enter by pressing B (page
E-9).
Seconds
To use the tachymeter
1. In the Stopwatch Mode, press C.
• The second hand will start to move, and will stop automatically when it reaches
60 seconds.
• The hour and minute hands indicate the current time in the Home City.
2. Press C again when the vehicle reaches one kilometer (one mile).
• This will stop the second hand. The value on the bezel that the second hand is
pointing to is the average speed at that point.
Example: After a vehicle runs one kilometer (one mile), the second hand is pointing at
120. This means that the average speed is 120 km/h (mph).
3. Hold down C for about one second to reset the tachymeter and return the second
hand to 12 o'clock.
E-21
Alarm time
AL3
AL4
E-23
E-25
E-27
E-29
Advertisement
