Parts And Functions - Haier AW-HDM009-N91 Operation Manual

Split type room air condition
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1

Parts and Functions

Indoor Unit
Inlet
1
1
2
2
Inlet grille
3
3
Outlet
Anion generator
5
4
6
6
(inside)
7
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Display board
1
Remote signal receiver
(A beeping sound is generated when a signal from remote controller isreceived.)
2
Power indicator
(Lights up when unit starts.)
3
Timer mode indicator
(Lights up whenTimer operation is selected.)
4
Operation mode indicator
5
WIFI
Display board
1
Signal receiver
2
Setting temp.display
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
Outdoor Unit
OUTLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
INLET
Please be subject to the actual produce purchased the
above picture is just from your reference
1
4
5
Air Purifying Filter
(inside)
Emergency
Vertical blade
(adjust left and
Display board
r ight air fl
ow)
(lights up when the compressor is on.)
1
2
Operation mode indicator
3
(lights up when the compressor is on.)
4
Remote controller
1
2
3
8
4
5
Switch
9
TURBO
10
11
12
SWING
13
14
HEALTH
15
TIMER
ON
16
17
1. Mode display
Operation mode
AUTO
COOL
Remote controller
2. Signal sending display
3. SWING display
4. FAN SPEED display
LO
MED
3
5. LOCK display
Healthy function is not available for some units.
Loading of the battery
4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or
room, the recei
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
6. TIMER OFF display
6
TIMER ON display
7. TEMP display
7
8. Additional functions display
Operation mode
QUIET
Remote controller
8
9. TURBO button
10.
HEAT button
18
11. COOL button
19
HEAT
12. SWING LEFT/RIGHT button
20
13.
FAN SPEED button
14. HEALTH button
21
15. SLEEP button
LOCK button
16.
22
17. LIGHT button
EATRA
SLEEP
FUNCTION
23
Control the lightening and extinguishing
TIMER
OFF
of the indoor LED display board.
24
18. POWER/SOFT button
25
19. DRY button
20. TEMP button
21.
SWING UP/DOWN button
22.
TIMER OFF/ON
23. EXTRA FUNCTION button
DRY
FAN
HEALTH AIRFLOW
Function:
24.CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions.
Display
25. RESET button
circulated
HI
AUTO
When the remote controller appears
abnormal, use a sharp pointed
article to press this button to reset
the remote.
1
Remove the battery cover;
2
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
3
Be sure that the loading
is in line with th
wireless telephone is installed in the
reload several minutes later.
Supplemented
electrical
SLEEP
HEALTH
TURBO
heating
button
---
AUTO
---
FAN
e" + "/"-";

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Aw-hdm012-n91Aw-hdm018-n91Aw-hdm024-n91

Table of Contents