Table of Contents
Advertisement
www.actoolsupply.com
www.actoolsupply.com
T
T
r
r
u
u
P
P
o
o
i
i
n
n
t
t
e
e
®
®
2
2
1
1
0
0
0
0
4
4
Quick
Quick
Battery Installation
Battery Installation
The following instructions describe how to install/replace batteries in the Tru Pointe
The following instructions describe how to install/replace batteries in the Tru Pointe
1.
1.
Turn
Turn
the
the
unit o
unit
over s
ver
2.
2.
Apply
Apply m
minimal pressur
inimal
pressure to
bottom of the instrument.
bottom of the instrument.
3.
3.
Install/Replace
Install/Replace
a 9v
a 9v
T
T
urning the
urning the
Instrument On/Off
Instrument On/Off
1.
1.
Plug t
Plug
the headphon
he
headphones into
2.
2.
Press
Press
the
the
On/Off
On/Off
3.
3.
Press
Press
the
the
On/Off
On/Off
NOTE:
NOTE:
If the unit is
If the unit is
can be heard
can be heard immediately
or "PrbS" mode, the Touch Probe must be in contact with
or "PrbS" mode, the Touch Probe must be in contact with
the item being tested to translate the
the item being tested to translate the
Airborne Leak Detection
Airborne Leak Detection
Use the Airborne Sensor for detecting pressurized gas leaks, vacuum leaks, or when using the
Use the Airborne Sensor for detecting pressurized gas leaks, vacuum leaks, or when using the
SoundBlaster
SoundBlaster
®
®
.
.
Leaks must be turbulent
Leaks must be turbulent t
Using the Tru Pointe
Using the Tru Pointe
1.
1.
Insert
Insert
the heads
the
headset plug
et plug
2.
2.
Push
Push
the
the
Power
Power
Button
Button
3.
3.
Push
Push
the Mo
the
Mode Select
de Select
press
press
or
or
to activate it.
to activate it.
▲
▲
▼
▼
255) will be displayed and
255) will be displayed and translat
Display will display the streng
Display will display the
hold its place for 5
hold its place for 5
4.
4.
The instrum
The
instrument always
ent always
the
the
▲
▲
or
or
▼
▼
buttons will adjust sensitivity up or down.
buttons will adjust sensitivity up or down.
play is at maximum, reduce the sensitivity by pressing
play is at maximum, reduce the sensitivity by pressing
and continue searching for the leak. Pointing the
and continue searching for the leak. Pointing the
leak will cause the bar graph level to drop. Pointing the detector toward, or getting
leak will cause the bar graph level to drop. Pointing the detector toward, or getting
closer to the leak, will
closer to the leak, will
www.actoolsupply.com
www.actoolsupply.com
Start
Start
Guide
Guide
so the
o the
controls
controls
are
are
facing
facing
the
the
oor.
oor.
fl
fl
e to
the
the batter
battery compart
y
compartment panel
ment panel
battery
battery, noting
, noting
the (+)
the (+)
and (-)
and (-)
positions on
positions on
es into
the jack
the jack
on the
on the
right side
right side
Button
Button
once
once
to
to t
turn
urn
the
the un
unit on.
it on.
Button
Button
again
again
to t
to
turn t
urn
the unit
he unit
off.
off.
in "AIR" mode, translated ultrasound
in "AIR" mode, translated ultrasound
immediately.
.
If the unit is in "PrbH", "PrbL",
If the unit is in "PrbH", "PrbL",
ultrasound.
ultrasound.
to be detected ultrasonically
o be detected
ultrasonically.
®
®
2100:
2100:
into t
into
the jack
he jack
on the
on the
side of
side of
once.
once.
Button
Button
until the
until the
alphanumeric
alphanumeric
Once activated, the
Once activated, the cur
current sensitivity sett
translated ultrasound will be heard.
ed ultrasound will be heard.
strength of the corresponding signal.
th of the corresponding signal.
seconds before resetting its position.
seconds before resetting its position.
resets
resets it
itself so
self so
that sens
that
sensitivity is
itivity is
Tru Pointe
Tru Pointe
cause the bar graph level
cause the bar graph level
to increase. Any deviation from
to increase. Any deviation from
I
I
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
0
0
0
0
2
2
8
8
-
-
9
9
0
0
0
0
3
3
®
®
2100.
2100.
and slide
and slide
it toward
it toward
the
the
the inner
the inner
label.
label.
of the
of the
instrument
instrument
.
the
the inst
instrument.
rument.
display
display
reads "A
reads
"AIR", t
IR",
then
hen
rent sensitivity
setting (0 to
ing (0 to
The Bar Graph
The Bar Graph
The highest LED will
The highest LED will
the active
the active
mode. Pr
mode.
Pressing
essing
If the LED Bar Graph
If the LED Bar Graph
Dis-
Dis-
▼
▼
until it reads "5" or less,
until it reads "5" or less,
®
®
2100 away from the
2100 away from the
5
5
Advertisement
Table of Contents
