Maintenance - Stanley STSP110 Original Instructions Manual

and tighten the screw to secure the depth.
• To prevent tool fault, the depth-of-cut adjustment knob
has been set to the optimal position at factory default.
• Users may also set the knob to a desired position at any
time.
Preparation before use
• Always observe the safety instructions and applicable
regulations.
• Ensure that the butterfly screw (3) is properly tightened
before operating the tool.
Switching On And Off (Fig. B)
To switch the tool on, press the on/off switch (1).
To switch the tool off, release the on/off switch.
This tool has a lock-on feature. To activate, press the on/off
switch and then the lock-on button (2). To de-activate, press
the on/off button again.
Always switch off the tool and then the power supply when
work is finished.
Cutting (Fig. E)
Align the front edge of the base with the cutting line on
the workpiece. Hold the tool firmly. Set the base on the
workpiece to be cut without the wheel making any contact.
Turn the tool on and wait until the wheel attains full speed.
Move the tool forward over the workpiece surface,
advancing smoothly until the cut is completed.
Keep the cutting line straight.
This tool should only be used on horizontal surfaces.
Be sure to move the tool gently forward, in a straight line.
Forcing, or exerting excessive pressure, or allowing the
wheel to bend, pinch or twist in the cut can cause the motor
to over heat and tool to kick back dangerously.
When the depth of cut is over 20mm deep, make 2 or 3
separate cuts to prevent motor failure.

MAINTENANCE

Your STANLEY tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
WARNING! To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/ installing any accessory. Before
reassembling the tool, press and release the
trigger switch to make sure the tool is already
switched off.
WARNING! Before performing any maintenance
on corded/ cordless power tools:
Carbon Brushes (Fig. F)
Remove and check carbon brushes regularly. Replace
when they have worn down to about 6mm or less.
Keep carbon brushes clean for free movement in the holder.
Both carbon brushes should be replaced at the same time.
Use only Stanley carbon brushes.
Use a slotted screwdriver to remove brush caps (5).
Remove worn brushes, insert new ones, and secure the
brush caps.
Lubrication
STANLEY tools are properly lubricated at the factory and
are ready for use.
Tools should be lubricated regularly every year depending
on usage. (Tools used on heavy duty jobs and tools
exposed to heat may require more frequent lubrication.)
This lubrication should be attempted only by trained power
tool repairperson's such as those at STANLEY service
centers or in other qualified service personnel.
Cleaning
WARNING! Dust and grit from metal grinding
often accumulate on interior surfaces and could
create an electrical shock hazard if not cleaned
out. Use only mild soap and a damp cloth to
clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a
liquid.
WARNING! Never use solvents or harsh
chemicals to clean non-metal parts of the tool.
These chemicals may weaken the material of
the parts. Use only mild soap and damp cloth
to clean the tool. Never let any liquid get inside
the tool; never immerse any part of the tool into
liquid.
WARNING! Do not overload your angle grinder.
Overloading causes a reduction in speed and
efficiency, causing your angle grinder to become
too hot. If this happens, operate your angle
grinder under no load for one or two minutes until
it has cooled to normal operating temperature.
Switching your angle grinder off under load will
reduce the life of the switch.
IMPORTANT! To ensure product SAFETY
and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this
manual) should be performed by authorized
service centers or other qualified organizations,
always using identical replacement parts. Unit
contains no user service able parts inside.
ACCESSORIES
WARNING: Since accessories, other than those
offered by STANLEY, have not been tested with
this product, use of such accessories with this
tool could be hazardous. To reduce the risk of injury, only
STANLEY, recommended accessories should be used with
this product.
The performance of any power tool is dependent upon the
accessory used. STANLEY accessories are engineered to
high quality standards and are designed to enhance the
performance of power tool. By using STANLEY accessories
will ensure that you get the very best from your STANLEY
tool. STANLEY offers a large selection of accessories
available at our local dealer or authorized service center at
extra cost.
( ENGLISH
Original Instructions)
7