Page 1 n e r M a n u a l...
Page 3 We urge you to review all these publications carefully. This will help you enjoy safe and trouble-free operation of your vehicle. When it comes to service, keep in mind that your GMC Truck dealer knows your vehicle best and is interested in your complete satisfaction. Your dealer invites you to return for all of your service needs both during and after the warranty period.
Page 4 Services Ltd., 1500 Bonhill Rd., Mississauga, Ontario L5T 1C7. G M T R U C K General Motors, GM and the GM Emblem, GMC and the GMC Emblem, SAFARI and the SAFARI Emblem are registered trademarks of General Motors Corporation.
Page 5 Model Reference This manual covers these models: Passenger Model Cargo Model...
Page 6: Table Of Contents
Table of Contents Introduction How to Use this Manual This section tells you how and vehicle damage warnings and symbols. Section 1 Seats and Safety Restraints This section tells you how to use your seats and safety restraints properly. Section 2 Features &...
Page 7: How To Use This Manual
How to Use This Manual Many people read their owner’s manual from beginning to end when rney first receive their new vehicle. This will help you learn about the features and controls for your vehicle. In this manual, you’ll find that pictures and words work together to explain things quickly.
Page 8 Safety Warnings and Symbols You will find a number of safety cautions in this book. We use gray background and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning. In the gray caution area, we tell you what the hazard is. Then we tell you what to do to help avoid or reduce the hazard.
Page 9 Vehicle Damage Warnings Also, in this book you will find these notices: NOTICE: These mean there is something that could damage In the notice area, we tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly.
Page 10 your These symbols are important for you and passengers whenever your vehicle is driven: Fasten Safety Door LocWUnlock Belts These symbols have to do with your lights: ' 0 0 Turn Signal Headlight Master Lighting Hazard Warning Direction Flasher High Beam Switch f o g Lights Daytime...
Page 11 some of These symbols are on Hood Release Ventilating Fan Rear Window Wiper & Washer These symbols are used on warning and indicator lights: Engine Coolant Battery Charging Temperature BRAKE Brake (Standard Cluster) Anti-Lock your controls: Windshield Windshield Wiper Washer Rear Window Defogger Fuel...
Page 12 Here are some other symbols may see:...
Page 13 Seats and Safety Belts Here you’ll find information about the seats in your vehicle and how to use your safety belts properly not do with safety belts Seats and Seat Controls ..........Frontseats .
Page 14: Seats And Seat Controls
Seats and Seat Controls This section tells you about the seats-how to and put them back in. It also tells you about bucket and bench seats, power seats, and head restraints. Seais Froni Manual Front Seat Slide the lever at the front of the seat to the left to unlock it. Slide the seat to where you want it.
Page 15 Power Driver’s Seat You can adjust the seat before entering the vehicle. Reclining Bucket Seats If you have this feature, you will have either a knob or a lever on the inside of the seat to adjust the seatback. The front control makes the front of the seat go up and down.
Page 16 Don’t adjust the driver’s seatback while your vehicle is moving. seatback reclined if your vehicle is moving. Don’t have If you have the lever, you can adjust the seatback by lifting the lever. Release the lever to lock the seat back where you want it.
Page 17: Rearseats
Rear Seats Bucket Seats If you have rear bucket seats in your vehicle, they will recline and adjust the same way as the front manual bucket seats. See “Front Seats” earlier in this section or in the Index. Bench Seats If you have bench seats in your vehicle, each seat can carry up to three passengers.
Page 18 To adjust your seatback, pull up the lever on the lower outside of the seat. The center bench seatbacks will recline further back than the rear bench seatbacks. To raise or lower the center console, press the button between the beverage holders.
Page 19 Seatback Latches (Non-Touring Bench Seats) After the latch has been released, push the seatback down until it locks in place. To raise the seatback, unlock the seat by pushing forward on the lever. Make sure the seatback is locked when it is put back in the upright position.
Page 20 BELTFOR SEAT REMOVAL 5. Lift up on the seat release latch. The latches are near the floor on the rear legs of the seat. To relieve pressure on the latch, pull back on the seat. 2. If you are removing the center seat, remove the right lapshoulder belt.
Page 21 To Install The Seat Make sure the seat is locked in by pulling up and down on the seat. 6. Lift up on the rear of the seat to remove the seat assembly from the rear latch pins. Then, pull back and lift the seat out of the vehicle.
Page 22: Head Restraints
Attach the quick release latch plate to the buckles in the roof. installing the center seat, connect the right lapshoulder belt to the attachment on the seat cushion. If you have seat, pull the belt through the guide before reattaching the lap-shoulder belt to the side of the seat.
Page 23: Safety Belts: They're For Everyone
Safety Belts: They’re For Everyone This part of the manual tells you how to use safety belts properly. It also teils you some things you should not do with safety belts. And it explains the Supplemental Inflatable Restraint, or “air bag” system. This figure lights up as a reminder to buckle up.
Page 24: Why Safety Belts Work
years of safety belts in vehicles, the facts After more than most crashes buckling up does matter Why Safety Belts Work When you ride in or on anything, you go as a lot! fast as it goes. For example, if the bike is going 10 mph (16 km/h), so is the child.
Page 25 ... "..When the bike hits the block, it stops. But the child keeps going! Take the simplest vehicle. Suppose it's just a seat on wheels. Put someone on it. 1-13...
Page 26 Get it up Then stop the vehicle. The rider doesn’t stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield or the instrument panel 1-14 speed..
Page 27: Questions Many People Ask About Safety Belts
With safety belts, you slow down as the vehicle does. You get more time to stop. stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense. Here Are Questions Many People Ask About Safety Belts Won ’t I be trapped in the vehicle after an accident safety belt?
Page 28: Safety Belt Reminder Light
a good driver doesn’t protect you from things beyond such as bad drivers. Most accidents occur within 25 miles (40 greatest number of serious injuries and deaths occur at speeds of less than 40 mph (65 kmh). Safety belts are for everyone. Safety Belt Reminder Light When the key is turned to eight seconds to remind people to fasten their safety belts.
Page 29: Driver Position
Driver Position This section describes the driver's restraint system. Lap-Shoulder Belt The driver has a lap-shoulder belt. Here's how to wear it properly. 1. Close and lock the door. 2. Adjust the seat (to see how, see "Seats" in the Index) so you can sit up straight.
Page 30 4. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. the belt isn’t long enough, see “Safety Belt Extender” at the end of this section. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 31 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 32 You can move the adjuster up from a lower position just by pushing up on it. To move it down, push in the adjuster at the arrows and pull down on the adjuster. After you move the adjuster to where you want it, try to move it up and down to make sure it is locked into...
Page 33 wrong What’s with this? The shoulder belt is too loose. It won’t give nearly as much protection this way. 1-21...
Page 34 What’s wrong with this? The belt is over an armrest. 1-22...
Page 35 What's wrong with this? arm. The shoulder belt is worn under the It should be worn over the shoulder at all times. 1-23...
Page 36 What’s wrong with this? The belt is twisted across the body. Before you close the door, be sure the belt is out of the way. If you slam the door on you can damage both the belt and your vehicle. To unlatch the belt, just push the button on the buckle.
Page 37: Driver's Facial Air Bag System
Driver’s Facial Air Bag System This section explains the Driver’s Facial Air Bag system. Here are the most important things to know: 1-25...
Page 38 Air Bag System Light There is an air bag readiness light on the instrument panel, which shows AIR BAG The system checks for electrical malfunctions, and the light tells there is a problem. Remember, if the air bag readiness light doesn’t come on when you start stays your vehicle, or on, or comes on when you are driving, your air bag...
Page 39 How The Air Bag System Works Where is the air bag? The Driver’s Facial Air Bag is in the middle of the steering wheel. When is an air bag expected to inflate? The air bag is designed to inflate in moderate to severe frontal or near-frontal crashes.
Page 40 How does an air bag restrain? In moderate to severe frontal or near-frontal collisions, even belted occupants can contact the steering wheel. The air bag supplements the protection provided by safety belts. Air bags distribute the force of the impact more evenly over the occupant’s upper body, stopping the occupant more gradually.
Page 41: Safety Belt Use During Pregnancy
the smoke from an air bag inflation harmful? The particles emitted during air bag inflation people. Some people with respiratory ailments may experience difficulty breathing if they stay in the vehicle with the windows closed after air bag inflation. So, if your air bag inflates, you and any passengers should exit the vehicle if and when it is safe to do so.
Page 42: Right Front Passenger Position
The best way to protect the fetus is to protect the mother. When is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 43: Rear Seat Outside Passenger Positions
Rear Seat Outside Passenger Positions Lap-Shoulder Belt These positions have lap-shoulder belts. Here’s how to wear one properly. 2. Push the latch plate into the buckle until it clicks. If the belt stops before it reaches the buckle, tilt the latch plate and keep pulling until you can buckle it.
Page 44 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 45 To unlatch the belt, just push the button on the buckle. 1-33...
Page 46: Center Passenger Positions
Center Passenger Pusitiun (Bench Seat) Lap Belt If your vehicle has rear bench seats, someone can sit in the center positions. When you sit in a center seating position, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along the belt.
Page 47: Children
Buckle, position and release it the same way as the lap part of a lapshoulder belt. If the belt isn’t long enough, see “Safety Belt Extender” at the end of this section. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 48: Smaller Children And Babies
Smaller Children and Babies 1-36...
Page 49: Child Restraints
Child Restraints Be sure to follow the instructions for the restraint. You may find these instructions on the restraint itself or in a booklet, or both. These restraints use the belt system in your vehicle, but the child also has to be secured within the restraint to help reduce the chance of personal injury.
Page 50 Top Strap If you need to have an anchor installed, you can ask your GM dealer to put it in for you. If you want to install an anchor yourself, your dealer can tell you how to do it. Securing a Child Restraint in a Rear Outside Position You’ll be using the lap-shoulder belt.
Page 51 1-39 4. Run the lap and shoulder portions through or around the restraint. The child restraint instructions will show you how. the shoulder belt goes in front of the child’s face or neck, put it behind the child restraint. Buckle the belt. Make sure the release button is positioned so you...
Page 52 To remove the child restraint, just unbuckle the vehicle's safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an adult or larger child passenger. Securing a Child Restraint in the Center Rear Seat Position When you secure a child restraint in a center seating position, you'll be using the lap belt.
Page 53 2. Put the restraint on the seat. Follow the instructions for the child restraint. 3. Secure the child in the child restraint as the instructions say. 4. Run the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how. 6.
Page 54 Securhg Child Restraint in the Right Front Seat You’ll be using the lapshoulder belt. See the earlier section about the top strap if the child restraint has one. 1. Put the restraint on the seat. Follow the instructions for the child restraint.
Page 55 To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an adult or larger child passenger. Press the button on the retractor cover to set the lock.
Page 56: Larger Children
Larger Children Children who have outgrown child restraints should wear the vehicle’s safety belts. If you have the choice, a child should sit next to a window so the child can wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 57 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? Move the child toward the center of the vehicle, but be sure that the shoulder belt still is on the child’s shoulder, so that in a crash the child’s upper body would have the restraint that belts provide.
Page 58: Safety Belt Extender
Wherever the child sits, the lap portion snug on the hips, just touching the child’s thighs. This applies belt force to the child’s pelvic bones Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use But if a safety belt isn’t long enough to fasten, your dealer will order you an extender.
Page 59: Checking Your Restraint Systems
Checking Your Restraint Systems make sure all Now and then, anchorages and reminder systems parts or damage. If you see anything that might keep a restraint system from doing its job, have it repaired. Replacing Safety Belts After a Crash If you’ve had a crash, do you need new belts? After a very minor collision, nothing may be necessary.
Page 60 " The model number on the replacement belt must be listed on the safety belt you want replace. Pull the shoulder belt all the way out to see this label. 1-48...
Page 61: Features & Controls
Features & Controls ..Here you can learn about the many standard and optional features on your vehicle. and information on starting. shifting. and braking are the instrument panel and the warning systems that tell you if everything is working properly- and what to do if you have a problem For explanation of vehicle symbols.
Page 62 All-Wheel Drive (Option) Windows Horn Tilt Wheel (Option) Turn Signalkiultifunction Lever Turn Signal and Lane Change Indicator Headlight High-Low Beam Windshield Wipers Windshield Washer Rear Window Wipermasher Cruise Control ........... Lights Mirrors .
Page 63: Keys
Keys...
Page 64 new vehicle is delivered, the dealer removes the plugs from the When keys, and gives them to the first owner. Each plug has a code on it that tells your dealer or a qualified locksmith how to make extra keys. Keep the plugs in a safe place. If you lose your keys, you’ll be able to have new ones made easily using these plugs.
Page 65: Your Doors And How They Work
Your Doors and How They Work Side Doors front open the side door from the outside. grasp the handle and pull the door open. To open the front side door from the inside, pull the lever toward you and push the door open.
Page 66 Sliding Side Door To open the sliding side door, pull the handle toward the back and slide the door to the rear until it latches in the open position. To close the sliding side door, pull the handle toward the front to release the rear latch, and slide the door forward.
Page 67 Rear Doors To close the rear doors, close the left door first. Check to make sure both doors are completely closed. The rear doors have a check assembly to keep the doors from opening beyond 90". To open the left rear door, pull on the latch release handle in the inside of the door.
Page 68: Doorlocks
See the caution under “Swing-Out Windows” in this section. Door Locks To fully open the doors, push in on the clip and lift the check assembly up off the mounting bracket. Do this on each door. Replace the assemblies the same way.
Page 69 There are several ways to lock and unlock your vehicle: Rear doors cannot be manually locked from the inside From the outside: your door key. From the inside: To lock front doors and sliding side door, slide the lock levers down. To unlock the front doors and the sliding side door from the...
Page 70 Power Door Locks The Power Door Lock switch will not lock or unlock the rear hatch and split panel doors. You must use the HATCH Switch” in the Index. Every vehicle with power door locks has a pulse lock system. A pulse lock system works like this: If the sliding door is open and you push the power door lock switch, the sliding door will not lock immediately.
Page 71 The hatch and doors will automatically lock when the hatch is shut. If the hatch is partially closed, the rear doors will lock and you will need to use the key or HATCH REL switch, located to the left of the steering column, to unlock them.
Page 72: New Vehicle "Break-In
Key in the /gnition If you walk away from your vehicle with the keys inside, it’s an easy target for joy riders or professional thieves - so don’t do it. When you park your vehicle and open the reminding you to remove your key from the ignition and take it with you. Always do this.
Page 73: Ignitionswitch
Ignition Switch Use your ignition key to start your vehicle. The ignition key lets you rurn the ignition switch to five different positions. ACC (Accessory): ACC lets you use things like the radio and the windshield wipers when the engine is off. To get into ACC, push in the key and turn it toward you.
Page 74: Starting Your Engine
NOTICE: If your key seems stuck in LOCK and you can’t turn it, be sure it is all the way in. If it is, then turn the steering wheel left and right while you turn the key hard. But turn the key only with your hand.
Page 75: Fuelregulator
3. If your engine still won’t start (or starts but then stops), it could be with flooded too much gasoline. Try this: Wait 15 seconds to let the starter motor cool down. Then push your accelerator pedal all the way to the START key in for no more than ten seconds.
Page 76: Engine Block Heater
Engine Coolant Heater (Engine Block Heater) (Option) In very cold weather, 0°F (-1 8°C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 77: Automatic Transmission
How long should you keep the coolant heater plugged in? The answer depends on the weather, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact a GM dealer in the area where you’ll be parking your vehicle.
Page 78 Ensure the shift lever is fully Your vehicle has a brake-transmission shift interlock. apply your regular brakes before you can shift from ignition key is the RUN position. If you cannot shift out of ease pressure on the shift lever “P’...
Page 79 (Overdrive) This position is for normal driving. If you need more power for passing, and you’re: Going less than about pedal about halfway down. Going about 35 mph (56 km/h) or more, push the accelerator pedal all the way down. You’ll shift down to the next gear and have more power.
Page 80: Locking Rear Axle
Lacking Rear Axle If you have this feature, your rear axle can give you additional traction on snow, mud, ice, sand or gravel. It works like a standard axle most of the time, but when one of the rear wheels has no traction and the other does, the loclung feature will allow the wheel with traction to move the vehicle.
Page 81: Shifting Into "P" (Park)
If you are on hill: See “Parking shows how to turn your front wheels. If you are towing a trailer and are parking on any hill: See “Towing a Trailer” in the Index. That section shows what to do first to keep the trailer from moving.
Page 82: Shifting Out Of "P" (Park)
Leaving Your Vehicle With the Engine Running If you have to leave your vehicle with the engine running, be sure your vehicle is in “P7, (Park) and your parking brake is firmly set before you leave it. After you’ve moved the shift lever into the hold the regular brake pedal down.
Page 83: Parking Over Things That Burn
Torque Lock If you are parking on a hill and you don’t shift your transmission into “P” (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it difficult to pull the shift lever out (Park).
Page 84: Engineexhaust
Engine Exhaust Running Your Engine While You’re Parked It’s better not to park with the engine running. But if you ever have to, here are some things to know. 2-24...
Page 85 Follow the proper steps to be sure your vehicle won’t move. See “Shifting Into ‘P’ (Park)’’ in the Index. If you’re pulling a trailer, see “Towing a Trailer” in the Index. 2-25...
Page 86: All-Wheel Drive (Option)
All- Wheel Drive If your vehicle has all-wheel drive, your engine’s driving power is sent to all four wheels for extra traction. Windows (Option) 2-26 This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle.
Page 87 Swing-Out Windows If you have optional power windows, the controls are on each of the front side doors. The driver’s door has a switch for the front passenger window as well. Your power windows will not move unless the ignition has been turned to 2-27 RUN.
Page 88 Hatch Release Switch The vehicle must be in unlock the split-panel doors. The hatch will release with or without the key in the ignition. (Park) or (Neutral) to release the hatch “P’ “ N ’ This switch is to the left of the steering column.
Page 89: Horn
Horn Tilt Wheel (Option) You can also raise it to you exit and enter the vehicle. To tilt the wheel, hold the steering wheel and pull the lever. Move the steering wheel to a comfortable level, then release the lever to lock the wheel in place.
Page 90: Turn Signal And Lane Change Indicator
The Turn Signal/Multifunction Lever The lever on the left side of the steering column includes your: Turn Signal and Lane Change Indicator Headlight High-Low Beam Windshield Wipers Windshield Washer Cruise Control (Option) Turn Signal and Lane Change Indicator To signal a turn, move the lever all finished, lever will return automatically.
Page 91 To signal a lane change, just raise or lower the lever until the green arrow starts to flash. Hold it there until you complete your lane change. The lever will return by itself when you release it. As you signal a turn or a lane change, if the arrows don’t flash but just stay on, a signal bulb may be burned out and other drivers won’t see your turn signal.
Page 92: Headlight High-Low Beam
Headlight High-Low Beam Windshield Wipers To change the headlights from low beam to high or high to low, pull the turn signal lever all the way toward you. Then release it. When the high beams are on, this blue indicator light on the instrument panel also will be on.
Page 93: Windshield Washer
For a single wiping cycle, turn the band to MIST. Hold it there until the wipers start, then let go. The wipers will stop after one cycle. If you want more cycles, hold the band on You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow.
Page 94 NOTICE: When using concentrated washer fluid, follow the manufacturer’s instructions for adding water. Don’t mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water doesn’t clean as well as washer fluid.
Page 95: Cruise Control
Press the top of the switch to the first position to turn on the wiper. Press the top of the switch in all the way and hold to release the desired amount washer fluid. The wipers will continue to work after you release the switch.
Page 96 To Set Cruise Control Get up to the speed you want. Push in the set button at the end of the lever and release it. your foot off the accelerator pedal. Take Move the Cruise Control switch to 2-36...
Page 97 To Resume a Set Speed Suppose you set your Cruise Control at a desired speed and then you apply the brake. This, of course, shuts off the Cruise Control. But you don’t need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can to R/A (Resume/Accelerate) and move the Cruise Control switch from hold it for about half...
Page 98 To lncrease Speed While Using Cruise Control While your cruise control switch is in the go to a higher speed. Here’s the first: Use the accelerator pedal to get to the higher speed. Push the button at the end of the lever, then release the button and the accelerator You’ll now cruise at the higher speed.
Page 99 To Reduce Speed While Using Cruise Control To slow down in very small amounts, push the button for less than half a second. Each time you do this, you’ll go 1 mph (1.6 k d h ) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed.
Page 100 To Get Out of Cruise Control There are two ways to turn off the Cruise Control: Move the Cruise OFF. switch to To Erase Speed Memory When you turn off the Cruise Control or the ignition, your Cruise Control set speed memory is erased. 2-40...
Page 101: Lights
Lights Press the top light switch to the left to turn on: Parking Lights Taillights License Plate Lights Instrument Panel Lights Press the bottom light switch to the left to turn on the headlights, together with: Parking Lights Taillights License Plate Lights Instrument Panel Lights Press to turn off all your lights.
Page 102 Fog Lamps Slide the right side of the switch to turn the fog lamps on, and the left side of the switch to turn them off. A warning light in the switch will remind you that your fog lights are on. Remember, fog lamps alone will not give off as much light headlights.
Page 103 Daytime Running Lights (DRL) Indicator Light (Canada Only) If your vehicle was first sold, when new, in Canada, you will have this ligh on the instrument panel. It goes on whenever the Daytime Running Lights are on, the ignition is on, the headlamp switch is off, and the parking brake is released.
Page 104 Headlights-On Reminder If you have this option, a reminder tone will sound when your headlights are turned on and your ignition is in OFF, LOCK or ACC. To turn the tone off, press the switch. Dome Lights Reading Lights You can adjust the lights to any desired position by rotating the lamp and they will work when the ignition is on or off.
Page 105: Mirrors
Interior Lights Override Switch If the switch is OFF, the interior lights will not come on when any of the vehicle doors are open. It is on the instrument panel above the radio. If you have the optional reading lamps, they will still operate if the switch is in the position.
Page 106 Outside Mirrors Your outside mirrors can also be folded in or out. Push the mirror towards the vehicle to move it in. After pushing the mirror out, adjustment will be maintained. You can mirror for day night driving. Press the tab forward (away from you) for day driving.
Page 107: Sunvisors
To move a mirror, slide the switch to for the passenger’s side mirror. Then, press the four-way pad to move the mirror in the desired direction. To make sure you do not accidentally move a mirror, slide the switch to the middle (off) position. Convex Outside Mirror Your right side mirror is convex.
Page 108 Cigarette Lighter/Ashtrays Don't hold a cigarette lighter in with your hand while it is heating. If you do, it won't be able to back away from the heating element when it's ready. That can make it overheat, damaging the lighter and the heating element. The optional cigarette lighter is on the left of the engine cover...
Page 109: Assist Handles
Don’t put papers and other things that burn into your ashtrays. If you do, cigarettes or other smoking materials could set them on fire, causing damage. Assist Handles Assist handles are located on the inside front and center vehicle pillars. To remove the smaller ashtrays on each sidewall, press down...
Page 110: Storage Compartments
Storage Compartments Your front storage compartment is at the center of the engine cover. To open the compartment, press the two tabs together and pull. If you have an optional sliding tray storage compartment, it is under the front passenger seat. To open the compartment, slide the latch in the top handle...
Page 111 Center Overhead Console lnstrument Cluster Your instrument cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel remains, and many other things you’ll need to know to drive safely and economically.
Page 112: Instrument Cluster
Instrument Panel 1. Light Switches 2. Dimmer Switch 3. Instrument Cluster 4. Gearshift Lever ConditionerLHeater 6. Fog Light Switch 7. Remote Outside Mirror Switch 8. Rear Heater Switch 9. Rear N C Switch 10. Interior Light Override Switch 11. Audio System 12.
Page 113 Speedometer and Odometer Standard Cluster Your speedometer lets kilometers per hour (kmdh). Your odometer shows how far your vehicle has been driven, in either miles (used in the U.S.) or kilometers (used in Canada). Tamper Resistant Odometer Cluster Digital Cluster Standard Your odometer is tamper resistant.
Page 114 The digital odometer will read You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then it must be. But if it can’t, then it’s set at zero, and a label must be on the dhver’s door to show the old mileage reading when the new odometer was installed.
Page 115: Warning Lights, Gages And Indicators
Warning Lights, Gages and Indicators This section describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury.
Page 116 If the warning light comes on, there could be brake system inspected right away. This light should come on as you start the vehicle. T f it doesn’t come on then, have it fixed so it will be ready to warn you if there’s a problem. If the light comes on while you are driving, pull off the road and stop carefully.
Page 117: Indicator Lights
If the light stays on, or comes service. If the regular brake system warning light isn’t on, brakes, but you don’t have anti-lock brakes. If the regular brake system warning light is also on, you don’t have anti-lock brakes and there’s problem with your regular brakes.
Page 118 Malfunction lndicator Lamp (SERVlCE ENGINE SOON) A computer monitors operation of your fuel, ignition and emission control systems. This light should come on when the ignition is on, but the engine is check to show you it is working. If it does not come on at not running, as all, have it fixed right away.
Page 119 Charging System Light Standard Cluster Digital Cluster The charging system light will come on briefly when you turn the ignition on, but the engine is not running, as a check to show you the light is working. Then it should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the electrical charging system.
Page 120 Daytime Running Lights (DRL) Indicator Light (Canadian Vehicles Only) The DRL indicator light is on the lower left of the standard cluster. If you have the digital cluster, it is on the top left. Headlight High Beam Indicator Light The light is on the left hand side of the standard cluster. If you have the digital cluster, it is on the top of the cluster.
Page 121: Gages
Turn Signal and Lane Change Indicator L ‘ Turn signal arrows are more details, see “Turn and Lane Change Signal” in this part. Gages Fuel Gage Standard Cluster The fuel gage tells you how much fuel you have remaining when the ignition is on.
Page 122 Here are things some owners ask about. None of these indicate with your fuel gage: At the gas station, the gas pump shuts off before the gage reads full. The fuel tank will take either a little more or a little less fuel to fill up than the gage shows.
Page 123 NOTICE: Damage to your engine from neglected oil problems can be costly and is not covered Engine Coolant Temperature Gage Cluster Standard If you have the Standard Cluster, you have a gage that shows the engine coolant temperature. If the gage pointer moves to the “H” (red) side, your engine is too hot! It means that your engine coolant has overheated.
Page 124 HOT COOLANT CAN BURN YOU BADLY! In “Problems on the Road,’’ this manual shows what to do. See “Engine Overheating” in the Index. Voltmeter Standard Cluster When your engine is not running, but the ignition is on (in the RUN position), the gage shows your battery’s state of charge in DC volts.
Page 125: Luggagecarrier
Luggage Carrier NOTICE: Loading cargo that weighs more than 200 pounds (91 kg) on the luggage carrier may damage your vehicle. When you carry large things, never let them hang over the rear or the sides of your vehicle. Load your cargo so that it rests on the slats and does not scratch or damage the vehicle.
Page 126: Trailer Wiring Harness
Trailer Wiring Harness you have the optional trailering package, your vehicle will have a 7-wire harness. The 7-wire harness is stored on the right side well. This harness has a 30 amp battery feed wire and no connector, and should be wired by a qualified service person. Attach the harness to the trailer, then tape or strap it to your vehicle’s frame rail.
Page 127 Notes...
Page 128 Notes...
Page 129: Comfort Controls & Audio Systems
Comfort Controls & Audio Systems In this section you’ll find out how to operate the comfort control and audio systems offered with your vehicle system supplied with your vehicle For explanation of vehicle symbols in this section. refer to “Vehicle Symbols”...
Page 130: Comfort Control
Comfort Controls Flow-Through Ventilation System Your vehicle’s flow-through ventilation system supplies outside air to the inside of your vehicle when it is moving. With the side windows closed, air will flow into the front air inlet grilles at the base of the windshield, through the vehicle and out the rear air exhaust valves.
Page 131 Air Vents If your vehicle doesn’t have air conditioning, there is an air vent in the right-hand kick panel below the instrument panel. The vent has a handle to open and close it. You will find air vents in the center and on the sides of your instrument panel.
Page 132: Heating System
Heating System Fan Lever The top lever has four positions. To increase the air flow, move the lever toward HIGH. To decrease the air flow, move it toward OFF. Temperature Lever The left lever lets you select the temperature of the air flowing vehicle.
Page 133: Heating/Air Conditioning System
Heating/Air Conditioning System If your vehicle has air conditioning, your heating/air conditioning system will look like this. Before using your vehicle’s air conditioning, open the windows to clear the vehicle of hot air. Close the windows when using the system. Fan Lever The top lever has five positions.
Page 134 BI-LEV A/C: With this, outside air comes out through the heater floor vent and the instrument panel vents. between cold and hot, cooler air will come out of the upper vents while warmer air comes out of the floor vent. This setting is useful in cool weather with bright sunlight.
Page 135: Rear Window Defogger
If your vehicle has rear air conditioning, setting it on LOW may enhance front N C performance by allowing trapped refrigerant in rear lines to circulate. The system will only send cooled air if the front system used to recirculate air, even if the front system is off. Before using the rear air conditioning, open the windows to clear the vehicle of hot air.
Page 136: Engine Coolant Heater
Engine Coolant Heater If you use the optional engine coolant heater before starting your engine, your heating system will produce warmer air faster to heat the passenger compartment in cold weather. See “Engine Coolant Heater” in the Index. Audio Systems Your Delco@ audio system has been designed to operate easily and give years of listening pleasure.
Page 137: How To Operate Your Etr' Am Radio
NOTICE: Before you add any sound equipment to your tape player, CB radio, mobile telephone or two-way radio sure you can add what you want. If you can, it’s very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’s engine, Delco@ radio or other systems, and even damage them.
Page 138 BAL (Balance) control behind and right speakers. The Lower Knob Turn the lower knob to choose radio stations. Tone Levers Two levers control the tone of your radio. BASS -Slide this lever up to increase the bass response. TREBLE -Slide this lever up to increase the treble response. Adjust this lever to give a pleasing sound.
Page 139: How To Operate Your Etr' Am-Fm Stereo Audio System
How to Operate Your ETW AM-FM Stereo Audio System This part tells you how your ETR@ AM-FM stereo audio system works: The Upper Knob The upper knob does these three things: It controls the volume. The VOL knob increases volume when rotated to the right.
Page 140 Pushbuttons The four pushbuttons let set the pushbuttons for up to eight favorite stations (4 AM and FM). Just: Tune in the station. Push SET. (SET appears in the VF display for a few seconds.) Within 5 seconds, push one of the four pushbuttons to store the station. Whenever you push that button, the preset station will return.
Page 141 How to Operate Your E T P AM-FM Stereo Audio Cassette System .. . This part tells you how your ETR@ AM-FM stereo audio cassette sound system works. The Upper Knob The upper knob does these four things: It controls the volume. The VOL knob increases volume with to the right.
Page 142 TREBLE -Slide this lever up to increase the treble response. Adjust this lever to give a pleasing sound. If a station is weak and noisy, move TREBLE down PWR (Power) The PWR button turns your system on and off. This is the Dynamic Noise Reduction button. It helps remove background hiss noise from the radio or tape player.
Page 143 Clock set the clock, just: Push SET. Within 5 seconas, push and hold Press and hold SEEK until the correct minute appears. To display the clock with the ignition off, push the upper knob. The time will be displayed for a few seconds. Cassette Tape Player Your tape player is built to work best with tapes that are 30 to 45 minutes long...
Page 144: Cassette System
How to Operate Your ETW AM-FM Stereo Audio Cassette System with Equalizer This part tells you how your ETR@ AM-FM stereo audio cassette system with equalizer works. The Upper Knob The upper knob does these four things: It controls the volume. The VOL knob increases volume with to the right.
Page 145 PW-R (Power) button turns your system on and off. AM-ST Button Push this button if you want AM stereo. (“STEREO” will be displayed when you are receiving an AM stereo station.) Cr02 Button The Cr02 button lets you set the system for the type of cassette being used. If you are using chrome or metal tapes, push the Cr02 button in.
Page 146 Clock To set the clock, just: Press SET. (SET appears in the VF display for a few seconds.) Within 5 seconds, push and hold SCAN until the correct hour appears. Press and hold SEEK until the correct minute appears. To display the clock with the ignition will be displayed for a few seconds.
Page 147: Care Of Your Cassette Tape Player
Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes, or a damaged mechanism. Cassette tapes should be stored in their cases away from contaminants, direct sunlight, and extreme heat. If they aren’t, they may not operate properly or cause failure of the tape player.
Page 148 How to Operate Your ETW AM-FM Stereo Audio Compact Disc (CD) This part tells you how your ETR@ AM-FM stereo system works: Upper Knob (PWR-VOL) The upper knob has three functions: It switches the radio It controls the volume. Volume will increase when the RCL knob is turned to the right and decrease when turned to the left.
Page 149 SEEK Pressing the SEEK station and stop. SEEK button will cause the receiver to seek the next lower Pressing the station and stop. SCAN When you press SCAN, the radio will go to the next station and pause, and will keep scanning until you press SCAN again. SC will be displayed when using this control.
Page 150 To Play A Compact Disc (CD) NOTICE: Before you begin, please note: DO NOT use mini-discs that are called singles. They won’t eject. USE FULL-SIZE COMPACT DISCS. If the disc player is very hot, or if you’re driving on a very rough road, a disc may come out or just not play.
Page 151 SCAN Press SCAN sample each track for approximately 10 seconds. Scanning will continue until the RDM, SCAN or any other motion button is pressed again. PREV If you hold the PREV disc will return to previous tracks. NEXT Press NEXT (SEEK the present track is finished.
Page 152 8. Press BAND and 000 will appear again. Now you are ready to enter the last three digits of your code. 6 and 7 for the last three digits of your code. 9. Repeat steps 10. Press BAND and rEP will appear for 5 seconds and then 000 will appear.
Page 153: Care Of Your Compact Discs
Care of Your Compact Discs Handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
Page 154 Notes 3-26...
Page 155: Your Driving And The Road
Your Driving and the Road Here you’ll find information about driving on different kinds of roads and in varying weather conditions . We’ve also included many other useful tips on driving ......... . Defensive Driving .
Page 156: Defensive Driving
Defensive Driving anyone can The best advice Please start with a very important safety device in your vehicle: Buckle up. (See “Safety Belts” in the Index.) Defensive driving really means “be ready for anything.” On city streets, rural roads, or freeways, it means “always expect the unexpected.” Assume that pedestrians or other drivers are going to be careless and make mistakes.
Page 157 According to the American Medical Association, a 180-pound (82 kg) person who drinks three 12-ounce (355 with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three k u n c e (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) It’s the amount of alcohol that counts.
Page 158 But it’s very important to keep in mind that the ability to drive is affected a BAC of 0.10 well below many people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent.
Page 159: Control Of A Vehicle
Control of a Vehicle have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator. All three systems have do their work at the places where the tires meet the road. Sometimes, as when you’re driving on snow or ice, it’s easy to ask more of those control systems than the tires and road can provide.
Page 160 Avoid needless heavy braking. Some people drive in spurts acceleration followed by heavy braking traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking.
Page 161: Steering
As you brake, your computer keeps receiving updates controls braking pressure accordingly. Remember: Anti-lock doesn’t change the time you need to get your foot up to the brake pedal. If you get too close to the vehicle in front of you, you won’t have time to apply your brakes if that vehicle suddenly slows or stops.
Page 162: Steering Tips
Steering Tips Driving on Curves It’s important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here’s why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves.
Page 163 An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Page 164: Passing
Passing The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again. A simple maneuver? Not necessarily! Passing another vehicle on a two-lane highway is a potentially dangerous move, since the passing vehicle occupies the same lane as oncoming traffic for several seconds.
Page 165: Loss Of Control
right lane. (Remember that your right outside mirror is convex. The vehicle you just passed may seem to be farther away from you than it really is.) Try not pass more than one vehicle at a time Reconsider before passing the next vehicle. Don’t overtake a slowly moving vehicle too rapidly.
Page 166: Drivingatnight
on a surface While driving sudden steering, acceleration, or braking (including engine braking by to a shifting lower gear). Any sudden changes could cause the You may not realize the surface is slippery until your vehicle is skidding. Learn to recognize warning clues snow on the road to make a “mirrored surface”...
Page 167: Driving In The Rain
Night Vision No one can see as well at night as in the daytime. But as we get older these differences increase. A 50-year-old driver may require at least twice as same much light to What do in the daytime can also affect your night vision. For example, if you spend the day in bright sunshine you are wise to wear sunglasses.
Page 168 less traction. It’s always wise to go slower and be cautious if rain starts to fall while you are driving. The surface may get wet suddenly when your reflexes are tuned for driving on dry pavement. The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking.
Page 169: Citydriving
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you’re going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Page 170: Freeway Driving
are ways Here to increase your Know the best way to get to where plan your trip into an unknown part of the city just as you would for a cross-country trip. Try to use the freeways that rim and crisscross most large cities. You’ll save time and energy.
Page 171 Just before you leave the lane, glance quickly over your shoulder to make sure there isn’t another vehicle in your “blind” spot. Once are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night. want to leave the freeway, move to the proper lane well in When advance.
Page 172: Hill And Mountain Roads
High way Hypnosis Is there actually such a condition as “highway hypnosis”? Or is falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that happen to you! If it does, your vehicle can leave the road in less than a...
Page 173 Know how to go down hills. The most important thing to know is this: let your engine do some of the slowing down. Shift to a lower gear when you go down a steep or long hill. Know how to go uphill. You may want to shift down to The lower gears help cool your engine and transmission, and you can climb the hill better.
Page 174: Winter Driving
Winter Driving Here are some tips for winter driving: Have your vehicle in good shape for winter. Be sure your engine coolant mix correct. You may want to put winter emergency supplies in your vehicle. Include an ice scraper, a small brush or broom, a supply of windshield washer fluid, a rag, some winter outer clothing, a small shovel, a flashlight, red cloth, and a couple driving under severe conditions, include a small bag of sand, a piece of old...
Page 175 What’s the worst time for this? “Wet ice.” Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get “wet ice” when it’s about freezing (32°F;...
Page 176 /f You’re Caught in a Blizzara If you are stopped by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. Here are some things to do to summon help and keep yourself and your passengers safe: Turn hazard flashers.
Page 177: Towing A Trailer
Run your engine only as long as you must. This saves fuel. When you run the engine, make it go a little faster than just idle. That is, push the accelerator slightly. This uses less fuel for the heat that you get and it keeps the battery charged.
Page 178 NOTICE: Pulling a trailer improperly can damage your vehicle and result in costly repairs not covered by your warranty. correctly, follow the advice in this section, and see your dealer for important information about towing a trailer with your vehicle. Every vehicle is ready for some trailer towing.
Page 179 Weight of the Trailer How heavy can a trailer safely be? It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important. And, it can also depend on any special equipment that you have on your vehicle.
Page 180 Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inflated to the limit for cold tires. You’ll find these numbers on the Certification label at the rear edge of the driver’s door or see “Tire Loading” in the Index, Then be sure you don’t go over the GVW limit for your vehicle.
Page 181 Will the trailer parts take 3,000 psi (20 650 P a ) of pressure? If not, the trailer brake system must not be used with your vehicle. If everything checks out this far, then make the brake fluid tap at the port on the master cylinder that sends fluid to the rear brakes.
Page 182 Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing You’ll need more passing distance up ahead when you’re towing a trailer. And, because you’re a good deal longer, you’ll need to go much farther beyond the passed vehicle before you can return to your lane.
Page 183 Parking on Hills You really should not park your vehicle, with a trailer attached, on a hill. If something goes wrong, your rig could start to move. People can be injured, and both your vehicle and the trailer can be damaged. But if you ever have to park your 1.
Page 184 Motes...
Page 185: Problems On The Road
Problems on the Road Here you’ll find what to do about some problems that can occur on the road Hazard Warning Flasher Other Warning Devices Jumpstarting Towing Your Vehicle Engine Overheating EngineFanNoise If a Tire Goes Flat Changing a Flat Tire Compact Spare Tire If You’re Stuck: In Sand.
Page 186 When the hazard warning flashers are on, your turn signals won’t work. Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lights will flash on and off. But they won’t flash if you’re braking.
Page 187: Other Warning Devices
Other Warning Devices If you carry reflective triangles, you can set one up at the side of the road feet (100 m) behind your vehicle. about Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle.
Page 188 Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles aren’t touching each other. If they are, it could cause a ground connection you don’t want. You wouldn’t be able to start your vehicle, and the bad grounding could damage the electrical systems. You could be injured if the vehicles roll.
Page 189 5. Check that the jumper cables don’t have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged, too. Before you connect the cables, here are some basic things you should know. Positive will go to positive negative or a metal engine part.
Page 190 Good Battery (-) Attach the cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, but the chance of marks getting back to the battery is much less.
Page 191: Towing Your Vehicle
Towing Your Vehicle Try to have a GM dealer or a professional towing service tow your vehicle. They can provide the right equipment and know how to tow it without damage. If your vehicle has been changed or modified since it was factory-new by adding aftermarket items like fog lamps, aero skirting, or special tires and wheels, these things can be damaged during towing.
Page 192 Don’t have your vehicle towed with the wheels in contact with the If a all-wheel drive. sling-type or wheel lift equipment, then either the front or rear wheels must be supported on a dolly. If your vehicle has rear-wheel drive, don’t have it towed on the rear wheels, unless you must.
Page 193 NOTICE: (Continued) Additional ramping may be required for car-carrier equipment, Use safety chains and wheel straps. If your vehicle has the all-wheel drive option, a dolly MUST be used under the rear wheels when towing from the front. Towing From the Front (Except AII-Wheel Drive) NOTICE: Do not tow with sling-type equipment or the front bumper system will be damaged.
Page 194 Towing From the Rear (Except AII- Wheel Drive) NOTICE: Do not tow with sling-type equipment or the rear bumper system will be damaged. Use wheel lift or car-carrier equipment. Additional ramping may be required for car-carrier equipment. Use safety chains and wheel straps. If your vehicle has the all-wheel drive option, a dolly MUST be used under the front wheels when towing from the rear.
Page 195: Engine Overheating
Engine Overheating If Steam Coming From Your Engine NOTICE: If your engine catches fire because you keep driving with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by your warranty. 5-11...
Page 196 If No Steam Is Coming From Your Engine If you get the overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: Climb a long hill on a hot day. Stop after high speed driving.
Page 197 When you decide it's safe to lift the hood, here's what you'll see: A. Coolant recovery tank B. Radiator pressure cap C. Engine fan If the coolant inside the coolant recovery tank is boiling, don't do anything else until it cools down. The coolant level should be at or above leak in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.
Page 198 How to Add Coolant to the Coolant Recovery Tank If you haven’t found a problem yet, but the coolant level isn’t at or above the FULL mark, add a 50/50 mixture of clean water (preferably distilled) and a proper antifreeze at the coolant recovery tank. (See “Engine Coolant” in the Index for more information about the proper coolant mix.) NOTICE: In cold weather, water can freeze and crack the engine, radiator,...
Page 199 How to Add Coolant to the Radiator 5-15...
Page 200 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly to the left until it first stops. (Don't press down while turning the pressure cap.) If you hear a hiss, wait for that to stop.
Page 201 7. By this time the coolant level inside the radiator filler neck may be lower. If the level is lower, add more of the proper mix through the filler neck until the level reaches the base of the filler neck. 4.
Page 202: Enginefannoise
Engine Fan Noise This vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most every day driving conditions the clutch is not engaged. This improves fuel economy and reduces fan noise.
Page 203: Changing A Flat Tire
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning flashers. Tire The following steps will tell you how to use the jack and change a tire. 5-19...
Page 204 Jack Storage Your jack, extension, ratchet and wheel blocks rear doors, along the passenger side wall. &i.e stored by your vehicle’s To remove your jack cover, take off the plastic wing nut by turning it to the left. Lift up on the latch and pull the jack cover off.
Page 205 Jacking Tool Storage 1. Nut 2. Washer 3. Wheel Blocks 4. Jack Lifthead 5. Jack 6. Jacking Instructions Tag To remove the ratchet and extension by turning the wing nut to the left. Remove the wing nut and retainer and take out the ratchet and extension.
Page 206 Spare Tire Your spare tire is stored underneath your vehicle. You will use the ratchet and extension to lower the spare tire. The ratchet has an side. DOWN side. And a 5-22...
Page 207 Put the flat end the extension on an angle through the hole in the rear door frame, above the bumper. Be sure the flat end connects into the hoist shaft. Attach the ratchet, DOWN with the facing you, to the extension.
Page 208 Changing the Tire The jack has a bolt on the end. Attach the socket end of the extension to the jack bolt like this. Attach the ratchet to the extension with the UP side facing you. Rotate the ratchet to the right.
Page 209 Put your spare tire near the flat tire. Remove the wheel trim. You have two wheel blocks stored with your jack. Place the blocks at the front rear of the tire farthest away from the one being changed. That would be the tire on the other side of the vehicle, at the opposite end.
Page 210 To remove the hubcap from the brushed aluminum wheel, fit the flat end of the extension into the notch and pop the hubcap off. Position jack under the vehicle. Place the ratchet and socket nut with the center cap With DOWN facing you, use the ratchet and socket to loosen all the wheel nuts.
Page 211 NOTICE: Raising your vehicle with the jack improperly positioned damage the vehicle or may allow the vehicle to fall off the jack. Be sure to fit the jack lift head into the proper location before raising your vehicle. Raise the vehicle by rotating the ratchet to the right.
Page 212 'lake Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. Place the spare on the wheel mounting surface. 5-28 the tlat tire.
Page 213 Replace the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub. Lower the vehicle by rotating the ratchet to the left. Lower the jack completely. 5-29...
Page 214 Tightening Wheel Nut Tighten the wheel nuts firmly in ratchet to the right with the UP marking facing you. NOTICE: Wheel covers won't fit on your compact Spare. If you try to put a wheel cover on your compact spare, you could damage the cover or the spare.
Page 215 Storing The Jack and Spare Tire Put the tire on the ground at the rear of the vehicle, with the valve stem pointed down. Pull the retaining bar through the center of the wheel, making sure it is properly attached. Attach the ratchet, with the extension.
Page 216: Compact Spare Tire
Compact Spare Tire Although the compact spare was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 Wa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inflated.
Page 217: If You're Stuck: In Sand. Mud. Ice Or Snow
If You’re Stuck: In Sand, Mud, Ice or Snow What you don’t want to do when your vehicle is stuck is to spin your wheels. The method known as “rocking” can help you get out when you re stuck, but you must use caution. NOTICE: Spinning your wheels can destroy parts of your vehicle the tires.
Page 218 Notes...
Page 219: Service & Appearance Care
Service & Appearance Care Here you will find information about the care of your vehicle . This part begins with service and fuel information. and then important fluid and lubricant levels . There is also technical information about your vehicle. and a section devoted to its appearance care . Service .
Page 220: Service
Service Your G.M dealer knows your vehicle best and wants you to be happy with it. We hope you’ll go to your dealer for all your service needs. You’ll get genuine GM parts and GM-trained and supported service people. We hope you’ll want to keep your GM vehicle all GM. Genuine GM parts have one of these marks: Doing Your Own Service Work If you want to do some of your own service work, you’ll want to get the...
Page 221 NOTICE: If you try to do your own service work without knowing enough about it, your vehicle could be damaged. The 8th digit of your Vehicle Identification Number (VIN) shows the code letter for your engine. You will find the VIN at the top left of your instrument panel.
Page 222 Ethanol is ethyl or grain alcohol. Properly-blended fuel that is no more than 10% ethanol is fine for your vehicle. Methanol is methyl or wood alcohol. NOTICE: Fuel that is more than 5% methanol is bad for your vehicle. Don’t use it. It can corrode metal parts in your fuel system and also damage plastic and rubber parts.
Page 223 Fuels in Foreign Countries If you plan on driving in another country outside the U.S. or Canada, unleaded fuel may be hard to find. Do not use leaded gasoline. If you use even one tankful, your emission controls won't work well or at all. With continuous use, spark plugs can get fouled, the exhaust system can corrode, and your engine oil can deteriorate quickly.
Page 224 While refueling, hang the cap inside the fuel door. To take off the cap, turn it slowly to the left (counter- clockwise).
Page 225: Checking Things Under The Hood
Be careful not to spill gasoline. Clean gasoline from painted surfaces as soon as possible. See “Cleaning the Outside of Your Vehicle” in the Index. When you put the cap back on, turn it to the right until you hear a clicking noise.
Page 226 Lift the hood, release the hood prop from its retainer and put the hood prop into the slot in the hood. Before closing the hood, be sure all the filler caps are on properly. Then lift the hood to relieve pressure on the hood Prop.
Page 227: Engineoil
" Engine Oil It's a good idea to check your engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. Then just pull the hood down and close it firmly.
Page 228 To Check Engine Oil Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip lower. When to Add Oil If the oil is at or below the ADD line, then you’ll need to add some oil. But you must use the right kind.
Page 229 What Kind of Oil to Use Beginning midyear 1993, oils of the proper quality for your vehicle will be identified with this new “starburst” symbol. The “starburst” symbol indicates that the oil has been certified by the American Petroleum Institute (API), and is preferred for use in your gasoline engine.
Page 230 You should also use the proper viscosity oil for your vehicle, as shown in the following chart: RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS FOR BEST FUEL ECONOMY AND COLD STARTING, SELECT THE LOWEST SAE VISCOSITY GRADE 011 FOR THE EXPECTED TEMPERATURE RANGE. WEATHER + 60 SAE SW-30...
Page 231 cannot find oils with the new “starburst” symbol on the front of the should look for and use oils containing the following three container, things: SHor SG “SH” or “SG” must be on the oil container, either by itself or combined with other quality designations, such “SGKD,”...
Page 232 Engine Oil Additives Don’t add anything to your oil. Your GM dealer is ready to advise if you think something should be added. When to Change Engine Oil See if any one of these is true for you: Most trips are less than 4 miles (6 km). It’s below freezing outside and most trips are less than 10 miles (16 km).
Page 233: Enginecover
Engine Cover In order to replace your air cleaner filter, you will have to remove your engine cover. It is inside your vehicle behind the instrument panel extension. To Remove the Engine Cover: 1. Move both front seats as far back as they will go. 2.
Page 234 4. Grasp the bottom 5. Disconnect the 6. Grasp the top of 6-16 of the extension. Lift up and then pull out. electrical connector for the cigarette lighter. Set the extension aside. the heater duct and pull down gently to remove.
Page 235 7. Remove the bolt from the engine cover bracket. 8. Loosen the nut and move the bracket out of the way. 9. Lift up on each of the two latches at the bottom of the cover. 6-17...
Page 236 When removing the cover, be careful not to damage the instrument panel or the trim. To Install the Engine Cover: Lift the engine cover into the vehicle and slide it all the way forward. Make sure the rubber seal is over the latches. Install the two screws at the engine cover.
Page 237: Aircleaner
8. Grasp the bottom of the instrument panel extension and install the top into the groove first. Then, push the bottom of the extension into place. 9. Install the two nuts and two screws on the extension. Air Cleaner To Remove the Air Cleaner Filter: If you have the 4.3L engine (VIN Code Z) with the round air cleaner, you must first remove the engine cover before changing the filter.
Page 238: Automatic Transmission Fluid
If you have the 4.3L engine (VIN Code W) with the square air cleaner, can change the air cleaner filter without removing the engine cover. Just lift the hood, unsnap both clips and remove the top. After changing the filter, snap both clips to secure the air cleaner.
Page 239 NOTICE: Too much or too little fluid can damage your transmission. much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system, starting an accurate reading if you check your transmission fluid. Wait at least 30 minutes before checking the transmission fluid level if you have been driving: When outside temperatures are above 90”...
Page 240 Ther vithout shutting off the engine, follow these steps: 3. Check both sides of the dipstick, and read the lower level. The fluid level must be in the COLD area for a cold check or in the cross-hatched area for a hot check. 1.
Page 241 How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transmission fluid to use. See “Recommended Fluids and Lubricants” in the Index. If the fluid level is low, add only enough of the proper fluid to bring the level up to the COLD area for a cold check or the check.
Page 242: Rearaxle
Rear Axle When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See “Scheduled Maintenance Services” in the Index. How to Check Lubricant What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use.
Page 243: Frontaxle
How to Check Lubricant What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See “Recommended Fluids and Lubricants” in the Index. Front Axle When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it.
Page 244: Enginecoolant
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See “Recommended Fluids and Lubricants” in the Index. Engine Coolant The following explains your cooling system and how to add coolant when it is low. If you have problem with engine overheating, see “Engine Overheating”...
Page 245 NOTICE: If you use an improper coolant mix, your engine could overheat and be badly damaged. The repair cost wouldn’t be covered by your warranty. Too much water in the mix can freeze and crack the engine, radiator, heater core and other parts. Some conditions, such as air trapped in the cooling system, can affect the coolant level in the radiator.
Page 246 To Add Coolant If you need more coolant, add the proper mix at the coolant recovery tank. Add coolant mix at the eecovery tank, but be careful not to spill 6-28...
Page 247 Radiator Pressure Cap NOTICE: Your radiator cap is a 15 psi (105 kPa) pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating. Be sure the arrows line up with the overflow tube on the radiator filler neck. Thermostat Engine coolant temperature is controlled by a thermostat in the engine coolant system.
Page 248: Power Steering Fluid
Power Steering Fluid How To Check Power Steering Fluid When the engine compartment is hot, the level should be at the HOT mark. When the engine compartment is cool, the level should be at the FULL COLD mark. What to Add Refer to the Maintenance Schedule to determine what kind of fluid to use.
Page 249: Windshield Washer Fluid
NOTICE: When adding power steering fluid or making a complete fluid change, always use the proper fluid. Failure to use the proper fluid can cause leaks and damage hoses and seals. Windshield Washer Fluid To Add, NOTICE: When using concentrated washer fluid, follow the manufacturer’s instructions for adding water.
Page 250: Brake Master Cylinder
Brakes Brake Master Cylinder Your brake master cylinder is here. It is filled with DOT-3 brake fluid. There are only two reasons why the brake fluid level in your master cylinder might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear.
Page 251 To. Check Brake Fhid The fluid levels should be above MIN. If they aren’t, have your brake system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the levels are above MIN and below the top of each window.
Page 252 Brake Wear Your vehicle has front disc brakes and rear drum brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).
Page 253: Replacing Brake System Parts
Replacing Brake System Parts The braking system on a modem vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good design and test have top-quality GM brake parts in braking.
Page 254: Fluidleakcheck
For more information on vehicle storage, contact your dealer’s service department, or write to: Adistra Corporation I 7 1 Hamilton Street Plymouth, MI 48 170 In Canada, write to: General Motors of Canada, Limited Customer Services Department Oshawa, Ontario Ll J Fluid Leak Check After the vehicle has been parked for awhile, inspect the surface beneath the vehicle for water, oil, fuel or other fluids.
Page 255 Headlights 1 . Open the hood. 2. Remove the four screws from the headlight bezel. Pull the bezel out so you can see the parkinghrn signal sockets. 3. Press the tab and turn the socket to the left to remove the socket from the bezel.
Page 256 7. Reverse steps 1-5 to reinstall the headlight. Front Parkingmum Signal Lights Open the hood. 2, Remove the four screws from the headlight bezel. Pull the bezel out so you can see the parkinghurn signal sockets. 5. Pull the connector out and unplug the light.
Page 257 5. Reverse steps 1-3 to reinstall the headlight. Rear Lights 1. Open the rear door. 4. Pull out the bulb and replace it with the new bulb. 3. Pull out the taillight assembly so you can see the socket. 6-39...
Page 258 6. Reverse steps 1-4 to reinstall the taillight. Center High Mounted Stop Lamp (CHMSL) $\s1 6-40 4. Press the tab and turn the socket to the left to remove the socket from the bezel. If the socket does not have a tab, turn the socket to the left to remove the socket from the...
Page 259 Other Maintenance /terns Front Suspension and Steering Linkage Refer to the Maintenance Schedule to determine how often to lubricate the fittings and what type of lubricant to use. Front Wheel Bearing (Two-Wheel Drive) If your vehicle is two-wheel drive, it has wheel bearings that must be cleaned and repacked.
Page 260 Air Conditioning Every now and then have your dealership check your air conditioning system to be sure it has not lost any cooling ability. If you think the system is not working properly, have your dealership check it out as soon possible.
Page 261 Door weatherstrips and rubber hood bumpers should be wiped clean with a wet cloth and lightly coated with Never use too much of any lubricant and be sure to wipe up any extra lubricant when you are finished. Some parts that need lubricating are hard to get at. Window regulators and controls are inside the doors.
Page 262: Loading Your Vehicle
Malfunction Indicator Lamp (SERVICE ENGINE SOON ) This light on your instrument cluster lets you know when your emission system needs service. The light will come on briefly when you start your engine to let you know that the system is working. If it does not come on when you start your engine, or if it comes on and stays on while you’re driving, your system may need service.
Page 263 And, if you do have a heavy load, you should spread it out. Using heavier suspension components to get added durability might not change your weight ratings. Ask your dealer to help you load your vehicle the right way. NOTICE: Your warranty does not cover parts or components that fail because of overloading.
Page 264 Payload The Payload Capacity is shown on the CertificationITire label. This is the maximum load capacity that your vehicle can carry. Be sure to include the weight of the people inside as part of your load. If you added any accessories or equipment after your vehicle left the factory, remember to subtract the weight of these things from the payload.
Page 265: Tires
Add-on Equipment When you carry removable items, you may need to put a limit on how many people you carry inside your vehicle. Be sure to weigh your vehicle before you buy and install the new equipment. NOTICE: Your warranty doesn’t cover parts or components that fail because of overloading.
Page 266 Inflation Tire Pressure The Certificationnire label which is on the rear edge of the driver’s door, shows the correct inflation pressures for your tires, when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven more than a mile.
Page 267 Tire Inspection and Rotation To make your tires last longer, have them inspected and rotated at the mileages recommended in the Maintenance Schedule. See “Scheduled Maintenance Services” in the Index. If your vehicle has front tires with different load ratings or tread designs (such as all season vs.
Page 268 When It’s Time for New Tires You need a new tire i f You can see the indicators at three or more places around the tire. You can see cord or fabric showing through the tire’s rubber. The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric.
Page 269 If you ever replace your tires with those not having a TPC Spec number, make sure they are the same size, load range, speed rating and construction type (bias, bias-belted or radial) as your original tires. Uniform Tire Quality Grading The following information relates to the system developed by the United States National Highway Traffic Safety Administration which grades tires by treadwear, traction and temperature performance.
Page 270 Temperature A, 9, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 271 Each new wheel should have the same load carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts, or wheel nut,s, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, and wheel nuts for your GM model.
Page 272: Appearancecare
Tire Chains NOTICE: If your vehicle has P245/60R15 they can damage your vehicle. If you have other size tires, use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the rear axle tires and tighten them as tightly as possible with the ends securely fastened.
Page 273 Never use these to clean your vehicle: Gasoline Benzene Naphtha Carbon Tetrachloride Acetone They can all be hazardous damage your vehicle, too. Don’t use any of these unless this manual says you can. In many uses, these will damage your vehicle: Alcohol Laundry Soap Bleach...
Page 274 Using Foam-Type Cleaner on Fabric Vacuum and brush the area to remove any loose dirt. Always clean a whole trim panel or section. Mask surrounding trim along stitch or welt lines. Mix Multi-Purpose Powdered Cleaner following the directions container label. Use suds only and apply with a clean sponge.
Page 275 Fabric Protection Your vehicle upholstery that has been treated with Scotchgard" Fabric Protector, a 3M product. Scotchgard water, which are the carriers of most stains. Even with this protection, you still need clean your upholstery often Further information on cleaning is available by calling 1-800-433-3296 (in Minnesota, 1-800-642-6 1 67).
Page 276 Cleaning Vinyl Use warm water and a clean cloth. Rub with a clean, damp cloth to remove dirt. You may have to do it more than once. Things like tar, asphalt and shoe polish will stain if you don’t get them off quickly.
Page 277 Clean the outside of the windshield with GM Windshield Cleaner, Bon-Ami Powder@ (GM Part No. 105001 1). The windshield is clean if beads do not form when you rinse it with water. Clean the blade by wiping vigorously with a cloth soaked in full strength windshield washer solvent.
Page 278 Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, you may use GM Chrome Polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim.
Page 279 Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer or other service outlets. Larger areas of finish damage can be corrected in your dealer’s body and paint shop.
Page 280 Appearance Care Materials Chart SIZE PART NUMBER 16 oz. (0.473L) Tar and 1050172 16 oz. (0.473L) Chrome Cleaner 1050173 16 oz. (0.473L) White Sidewall 1050174 10502 14 16 oz. (0.473L) Fabric 1050244 23 oz. (0.680L) Glass 1050427 6 lbs. (2.72 kg) Multi-Purpose 1050429 8 oz.
Page 281: Vehicle Identification Number
Vehicle Identification Number (VIA/) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VTN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration.
Page 282 Engine ldentification The eighth character in your VIN is the engine code. This code will help you identify your engine, specifications, and replacement parts. c ' ) 6-64...
Page 283: Service Parts Identification Label
Service Parts Identification Label You’ll find this label on the inside of the glove box door. K19 K64 LC3 M X l M31 NA5 6BJ 62L 62U 67D 671 679 7BJ 8HJ 9HJ PAINTTECHNOLOGY It’s very helpful if you ever need to order parts. On this label is: your VIN, the model designation,...
Page 284 Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers, and fusible thermal links in the wiring itself. This greatly reduces the chance of fires caused by electrical problems.
Page 285 Fuse Block To remove fuses if you don’t have a fuse extractor, hold the end of the fuse between your thumb and index finger and pull straight out. Be sure to use the correct fuse. If you ever have a problem on the road and don’t have a spare fuse, you can “borrow”...
Page 286: Capacities And Specification Charts
Capacities and Specification Charts Replacement Parts Replacement part numbers listed in this section are based on the latest information available at the time of printing, and are subject to change. If part listed in this manual is not the same when it was built, or if you have truck dealer.
Page 287 Cooling System Capacity ENGINE VIN CODE 4.3L 4.3L *All quantities are approximate. After refill, the level MUST be checked. Crankcase Capacity ENGINE VIN CODE 4.3L 4.3L *All quantities are approximate. After refill, the level MUST be checked. Do not overfill. Fuel Tank Capacity TYPE Standard Tank...
Page 288 Lamp and Bulb Data EXTERIOR LAMPS Headlamps (Halogen) Park, Signal Lamp Tail, Stop Lamps Marker Lamps Backup Lamp License Lamp CHMSL Assembly INTERIOR LAMPS Dome Lamp (w/o Roof Console) Dome Lamp (with Roof Console) Glove Lamp Heater & AC Control Visor Vanity Mirror Lamps Stepwell Lamp Reading Lamp (with Roof Console)
Page 289 LAMPS General Indicator Lamp? Instrument Cluster I l l u m . ~ Headlamp Beam Indicator Lamp? Headlamp Beam Indicator Lamp$ Malfunction Indicator Lamp (Service Engine Soon)? Malfunction Indicator Lamp (Service Engine Soon)$ Directional Indicator? Directional Indicator$ Brake Warning Indicator Lamp? Brake Warning Indicator Lamp$ Transmission Indicator Dial$ Fog Lamps...
Page 290: Fuses And Circuit Breakers
Fuses and Circuit Breakers 6941 €3 SHUNT CIG LTWDM HRNlTL LPS Fuse Legend 5 Amp - Tan 7.5 Amp - Brown 10 Amp Amp -Blue SHUNT GAGES 15 Amp 30 Amp STOPlHAZ Blue Yellow Clear Green...
Page 291 NAME PROTECTED Instrument Panel Lamps, INST LPS Radio Dial Lamps, Heater Lamps Power Door Locks, Power PWR ACCY Seat CIG LTR/DM Digital Clock, Cigarette Lighter, Dome Lights, Radio Memory, Glove Box Lamp Instrument Cluster Gages, GAGES Brake Switch, Audio Alarm, Headlight Switch Illumination, Ash Tray Illumination, Cruise Control...
Page 292 NAME DRL** Canadian Daytime Running Lights Power MIRRORS* TRAILER* Trailer Wiring *In-line fuse **Canada only ***In-line fuse (certain models) Service Replacement Part and Filter Recommendations ENGINE (VIN) FILTER AIR CLEANER FILTER PCV VALVE SPARK PLUGS* FUEL FILTER RADIATOR CAP *Use copper-cored resistor type spark plugs. CIRCUITS PROTECTED Mirror...
Page 293 Air Conditioning Refrigerants Not all air conditioning refrigerants are the same. If the air conditioning system in your vehicle needs refrigerant, be sure the proper refrigerant is used. If you’re not sure, ask your GM dealer. For additional information, see your “Warranty and Owner Assistance Information”...
Page 294 Notes...
Page 295: Scheduled Maintenance Services
Scheduled Maintenance Services This section covers the maintenance required for your vehicle. Your vehicle needs these services to retain its safety, dependability, and emission control performance. A Word About Maintenance Your Vehicle and the Environment ..Scheduled Maintenance Services .
Page 296: A Word About Maintenance
A Word About Maintenance We at General Motors want to help you keep your vehicle condition. But we don’t know exactly how you’ll drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather.
Page 297: Scheduled Maintenance Services
Scheduled Maintenance Services This part tells you the maintenance services you should have done and when you should schedule them. Your GM dealer knows your vehicle best and wants you to be happy with it. If you go to your dealer for all your service needs, you’ll know that GM-trained and supported service people will perform the work using genuine GM parts.
Page 298 MAlNTENANCE SCHEDULE Item Axle Drive Brake Systems Inspection** Emission Control Service e “Explanation of Scheduled Maintenance Services” in the Index e California Air Resources Board has determined that the failure to perform this $ Tt lintenance item will not nullify the emission warranty or limit recall liability prior to the mpletion of vehicle useful life.
Page 299 MAINTENANCE SCHEDULE I (continued) THE SERVICES SHOWN ON THIS CHART UP TO 60,000 MILES (100 000 km) ARE TO BE DONE AFTER 60,000 MILES AT THE SAME INTERVALS. T1002...
Page 300: Maintenance Schedule I 1
MAINTENANCE SCHEDULE I 1 Miles (000) Item Service Engine Oil Change*-Every 12 Months, or Oil Filter Change*-Every 12 Months, or Chassis Lubrication-Every 12 Months, or Cooling System Service* -Every 24 Months or Air Cleaner Filter Replacement* Front Wheel Bearing Repack (2WD Only) Transmission Service Fuel Filter Replacement*$...
Page 301: Explanation Of Scheduled Maintenance Services
Explanation Of Scheduled Maintenance Services Below are explanations of the services listed in the maintenance charts. The proper fluids and lubricants to use are listed in this section. Make sure whoever services your vehicle uses these. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle.
Page 302 6. TRANSMISSION SERVICE: 15,000 filter every under or more of these conditions: In heavy city traffic. Where the outside temperature regularly reaches 90°F (32 higher. In hilly or mountainous terrain. Frequent trailer pulling. Uses such as taxi, police, delivery or other commercial service. If the vehicle is not used mainly under any of these conditions, change the fluid and filter every Transmission Fluid”...
Page 303 13. TIRE AND WHEEL ROTATION AND INSPECTION proper wear and maximum tire life, rotate tires at the first 6,000 miles (10 000 kilometers) for Schedule I or 7,500 miles (12 500 kilometers) for Schedule I1 and then every 15,000 miles thereafter.
Page 304: Owner Checks And Services
Owner Checks Listed below are owner checks and services which would be made time period specified to help ensure proper safety, emission performance, and dependability your vehicle. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper as shown in this section.
Page 305 Steering Column Lock Operation LOCK in each gear shift position. The key should turn to LOCK only when the gear shift is in (Park). On all vehicles, the key should come out only in LOCK. Parking Brake and Transmission Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the manual parking brake.
Page 306: Periodic Maintenance Inspections
Periodic Maintenance Inspections Listed below are inspections and services which should be performed at least twice a year (for instance, GM dealer’s service department or other qualified service center do these jobs. Make sure any necessary repairs are completed at once. Steering and Suspension Inspection? and steering system for damaged, loose or missing parts, signs of wear or lack of lubrication.
Page 307: Recommended Fluids & Lubricants
Recommended Fluids & Lubricants NOTE: Fluids and lubricants identified below by name, part number or specification may be obtained from your GM Dealer. USAGE Engine Oil Engine Coolant Hydraulic Brake Systems Parking Brake Cable Power Steering System Manual Steering Gear Automatic Transmission Differential: a.
Page 308 USAGE Hood Latch Assembly: a. Pivots and spring anchor b. Release Pawl Front Wheel Bearings Automatic Transmission Shift Linkage, Floor Shift Linkage, Hood and Door Hinges, Body Door Hinge Pins, Folding Seat, Door Fuel Hinge Key Lock Cylinders Chassis Lubrication Windshield Washer Solvent Weatherstrips Gas Line...
Page 309: Maintenance Record
Maintenance Record After each of the preceding Scheduled Maintenance Services is performed, record the date, odometer reading, services performed (list item numbers) and who performed the services in the appropriate column. In addition, retain copies of your receipts. It is suggested that receipts be kept with your Owner’s Manual.
Page 310 Service Sfafion Checks It is important for you or a service station attendant to perform these under-hood checks at each fuel fill. Check the engine oil level and add if necessary. Check the engine coolant level and add if necessary. Check the windshield washer fluid level and add if necessary.
Page 311 Hood Release Lever Page 6-7. Battery The Delco Freedom battery needs no water. See Page 6-35. Brake Fluid Reservoir See Page 6-32. Automatic Transmission Fluid See Page 6-20. Fuel Capacity 27 US. Gal. (102 L.). Use unleaded only. 87 octane or higher.
Page 312 Notes 7- 18...
Page 313: Customer Assistance Information
Customer Assistance Information Here you will find out how to contact GMC Truck if you need assistance. This section also tells you how to obtain service publications and how to report any safety defects. Customer Satisfaction Procedure .......
Page 314: Customer Satisfaction Procedure
Vehicle delivery date and present mileage Nature of concern We encourage you to call the toll free number listed previously in order to give your inquiry prompt attention. However, if you wish to write GMC Truck, write to: GMC Truck Customer Assistance 3 1 E.
Page 315: Customer Assistance For The Hearing Or Speech Impaired (Tdd)
General Motors reserves the right to change eligibility limitations and/or to discontinue its participation in this program. Both GMC Truck and your GMC Truck dealer are committed to making sure you are completely satisfied with your new vehicle. Our experience has...
Page 316: Reporting Safety Defects To The United States Government
AUTO LINE, but you may contact the BBB at any time. The BBB will attempt to resolve the complaint by serving as an intermediary between you and GMC Truck. If this mediation is unsuccessful, an informal hearing will be scheduled where eligible customers may present their case to an impartial third-party arbitrator.
Page 317: Reporting Safety Defects To The Canadian Government
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-GMC-TRUCK (1-800-462-8782) GMC Truck Consumer Relations 3 1 E. Judson Street 1607-04 Pontiac, MI 48342-2230 In Canada, please call us at 1-800-263-3777 (French).
Page 318: Roadside Assistance
We also provide dealer information at no charge such as location of the nearest GMC Truck dealer and their hours of operation. Roadside Assistance is available 24 hours a day, seven days a week, 365 days a year, including weekends and holidays.
Page 319: Service Publications
Individual PSP’s If you don’t want to buy all the PSP’s issued by GMC Truck for all models in the model year, you can buy individual PSP’s, such as those which may pertain to a particular model.
Page 320 What You’ll Find in the Index: A list of all PSP’s published by GMC Truck in a model year. PSP’s covering all models of GMC light trucks are listed in the same index. Ordering information Price information for the PSP’s you may want to buy.
Page 321 Notes...
Page 322 Above Subscription With Binder Binder Only Prices Subject To Change Without Notice. tell how to operate and service your vehicle. GMC Truck Service Publications Post Office Box 436006 Pontiac, MI 48343 call us TOLL FREE at 1-800-627-5699. Ask for form number 15959036-it...
Page 325: Index
Index AirBag Servicing Your Air Bag-Equipped Vehicle Aircleaner Airconditioning FanLever ..........FunctionLever .
Page 326 Trailer ..........Wear Indicators Braking In Emergencies...
Page 327 Damage ............Finish .
Page 328 Exhaustsystem Fan Noise Filter Replacement Chart Finish Care Damage Fluid Automatic Transmission Brake Capacities CoolantRecovery ........... FrontAxle Leakcheck .
Page 329 Hazard Warning Flashers HeadRestraints Headlights High Beam Indicator Light ..........High-LowBeam Reminder HeatingSystem...
Page 330 Loading Your Vehicle Lubrication Accelerator Control System Body Sliding Door Tracks Front Suspension and Steering Linkage Front Wheel Bearings (Two Wheel Drive) ..........LatchesandHinge Lockcylinders RearAxle...
Page 331 Visorvanity Windows Powersteering Fluid Product Service Publications Radiator Pressure Cap Radio (See “Audio Systems”) ReadingLights RearDefogger Rear HatcWSplit Panel Doors Rear Wipermasher Recommended Fluids/Lubricants Reporting Safety Defects Roadside Assistance Rocking Your Vehicle ........... RoofConsole .
Page 332 Publications Replacement Part/Filter Recommendations StationsChecks Servicing Your Facial Air Bag-Equipped Vehicle Shifting Into P (Park) Shifting Out Of P (Park) Single Belt Accessory Drive SpareTire SpecificationCharts Speedometer Springs. Fiberglass Starting Your Engine Steering InEmergencies Tips Storage Compartments Storing the JacWSpare Tire SunVisors Theft .
Page 333 Vehicle Damagewarnings Identification Number Storage Symbols ..........Ventilation System AirVents .
Page 334 Notes...
Page 335 Notes...
Page 336 Notes...
Page 337 Notes...
Page 338 Notes...
Page 340 X-941 0 WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION THROUGH National Institute for AUTOMOTIVE SERVICE EXCELLENCE Keep with vehicle at all times. Contains Important Operating, Safety, and Maintenance Instructions. TRUCK THE STRENGTH OF EXPERIENCE.

This manual is also suitable for:

1994 safari passenger

GMC 1994 Safari Owner's Manual

Table of Contents

Seats and Safety Belts Section

Features & Controls *

Comfort Controls & Audio Systems Section

Your Driving and the Road Section

Problems on the Road Section =

Service & Appearance Care Section

Scheduled Maintenance Services Section

Quick Links

Chapters

Related Manuals for GMC 1994 Safari

Summary of Contents for GMC 1994 Safari

This manual is also suitable for:

Table of Contents