Related Manuals for Lumberjack RHD1050
Summary of Contents for Lumberjack RHD1050
- Page 1 SAFETY AND OPERATING MANUAL SDS Rotary Hammer Drill RHD1050 O RIGINAL INSTRUCTIONS RHD1050...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Welcome to Lumberjack! Dear Customer, Congratulations on your purchase. Before using the product for the first time please be sure to read these instructions for use. They provide you with all information necessary for using the product safely and to ensure its long service life. -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. RHD1050... - Page 4 Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. RHD1050...
- Page 5 STARTING the operation, jog the chisel These carry important safety information. If switch to make sure the chisel bit does not wobble unreada ble or missing, Contact Lumberjack Tools for a replacement. or vibrate. g) Avoid unintentional starting. Prepare to...
- Page 6 To red uce vibration, maintain the tool as greater the capacity of the cord. explaine d in this manual. If any abnormal e) When using a cable reel, always unwind the vibration occurs, stop use immediately. cable completely. RHD1050...
-
Page 7: Symbols & Cable Rating Chart
SYMBOLS AND POWER RATING CHART Danger! – Read the operating Caution! Wear safety goggles. instructions to reduce the risk of injury. Caution! Wear ear defenders. The impact of noise can cause damage to hearing. Caution! Wear a dust mask. RHD1050... -
Page 8: Machine Details And Product Features
-13mm 1/2” Drill Chuck With SDS Shaft Adaptor and Chuck Key -8,10,12 X 150mm SDS Drill Bit -14 X 250mm SDS Point Chisel & SDS Flat Chisel -Grease Pot -1 Spare Set of Carbon Brushes -1 Gear Box Key RHD1050 AIR6V AIR6V AIR6V AIR6V... - Page 9 MACHINE DETAILS AND PRODUCT FEATURES RHD1050 AIR6V AIR6V AIR6V AIR6V...
- Page 10 To switch off release the trigger. Do not use the chisel until you are satisfied the bit is secured. FIG2 WARNING: The electric hammer chisel continues for a few seco nds after the trigger has been release, be careful when putting it down. RHD1050...
-
Page 11: Maintenance And Service
3.Safe operation, always make sure you have a yellow) conductor in the cord is the grounding stable po sture and safe footing before operating wire. Never connect the green(or green and the elect ric hammer chisel. yellow) wire to a live or neutral terminal. RHD1050... - Page 12 Note: Oil for the electric hammer chisel is sold stroke even when the motor rotates this may be separately, use Shell oil ROTELLA 40(engine oil) or because the oil has become thick equivalent, this is sold at most shops or filling stations anywhere. RHD1050...
- Page 13 4.All safety apparel. Safety Glasses Safety shoes. Safety gloves. Ear Defenders and Safety Hat are being worn. Always keep carbon brushes clean and ensure that they slide freely within the brush holders. Failure to adhere to these safety rules can greatly increase the chances of injury. RHD1050...
- Page 14 Do NOT attempt to modify tools or create accessories not recom mended. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury. It w ill also void any warranty given. RHD1050...
- Page 15 Outer Flange/ Arbor Nut or brush effectively 2. Disc accessory may be is tight. damaged, worn or wrong 2. Check condition and type of disc type for the material. accessory. Use only proper type of disc accessory in good condition. RHD1050...
-
Page 16: Lumberjack Guarantee
If a 1.2.3 If asked to do so by Lumberjack or its return is requested by the Authorised Dealer or Authorised dealer, you return the product at Lumberjack, you will be provided with a Returns your own cost to Lumberjack’s or supplying... - Page 17 Lumberjack. If you include a contact number with this it will speed your claim 2.4 Please note that it is essential that the letter of claim reaches Lumberjack on the last day of this Guarantee at the latest. Late claims will not be considered.
-
Page 18: Declaration Of Conformity
Old Heath Road, Wolverhampton, WV1 2RP. Tel: 01902 450 470 Declares that the Rotary hammer(RHD1050) Is in compliance with the regulations included in the Directives:2006/42/EC EC DECLARATION OF CONFORMITY Certificate for EC-type examination delivered by BV LCIE CHINA ,Building 4,No.518, xin zhuan Road, CaoHejing Songjiang Hight-Tech Park, Shanghai P.R.C(No.:1866AS07ZDE28863) -
Page 19: Parts List
Socket head caps screw M4*14 Spring 33*2*5.5*55 Ring 14*2 Spring 46.5*2*3.5*15 Knob shaft Stop plate Ring 18 Ring 50*1.6 Knob Clutch Self-tappings screw M4*12 Cone gear Spring 0.6*4.5*17.5 Ring 28*1.5 Button Hammer Bearing 6002-2RS Ring 19*3.1 Ring 32 RHD1050 AIR6V AIR6V AIR6V... - Page 20 Bearing 6000 Auxiliary handle Bearing plate Bracket Rotor Spring W7.8*0.9*18 Ring 8.1*21*0.5 Bracket button Bearing 608 T bolted m8*45 Fan guide Hoope Self-tapping screw ST3.9*65 Depth Stator Copper buckle Self-tapping screw ST4.8*50 Motor house Brush planes RHD1050 AIR6V AIR6V AIR6V...
-
Page 21: Parts Diagram
Parts Diagram RHD1050...
Need help?
Do you have a question about the RHD1050 and is the answer not in the manual?
Questions and answers