Advertisement
In the DDS system, an OCU DP located at an end office
interfaces the customer to the T carrier system. A 4-wire
loop is terminated at the customer premises by a data
service unit (DSU) or a channel service unit (CSU). It can
be used in the hub office, intermediate office, end office,
®
or SLC
terminal to extend the DDS network to that office
which has previously served voice channels exclusively.
The ADTRAN All-Rate Extended Range D4-OCU DP is
interchangeable with the following AT&T units:
• Subrate OCU DP (J98726DB)
• 56 kbps OCU DP (J98726DE)
• All Rate OCU DP (J98726DJ)
The unit is also interchangeable with all previous and
current ADTRAN units including the following:
• All-Rate OCU DP (1102005A)
• All-Rate with 38.4/64 kbps OCU DP (1102006A)
• All-Rate OCU DP (1104005L9)
2.
INSTALLATION
After unpacking the unit, immediately inspect it for
possible shipping damage. If damage is discovered, file
a claim immediately with the carrier and contact ADTRAN
Customer Service (see subsection 7).
The D4-OCU DP plugs directly into a WECO
equivalent, D4 channel bank, ADTRAN General Purpose
Communication (GPC) shelves, or ADTRAN ACT-1241
channel bank. No installation wiring is required.
A sixteen-position rotary switch on the faceplate and an
internal ten-position slide switch (SW1) must be set prior
to installing the unit.
Sixteen-Position Rotary Faceplate Switch
The settings for the sixteen-position rotary switch select
loop rates of 2.4, 4.8, 9.6,19.2, 38.4, 56, SW56, or 64
kbps, and Secondary Channel (SC). Set the switch functions
as illustrated in Figure 2.
When 64 kbps is selected, normal loopbacks
are automatically disabled.
loopback may be used at this rate. When SW56
is selected as the operating rate, SW1-1 must
remain off.
________________________________________
SLC is a registered trademark of AT&T
WECO is a registered trademark of AT&T
2
Internal Switch Option Settings
The location of the ten-position slide switch is illustrated
in Figure 3. The option settings are provided in Table B.
SW1 is a ten-position slide switch which enables or
disables error correction, bank type, zero code
suppression, latching loopback, hardware A/B signaling,
®
, or
quality monitoring, and extended transmit range.
If more than one bank type is selected (on), the OCU DP
will not function.
Only latching
Section 61107005L2-5, Issue 3
56
38.4
19.2
SC
9.6
4.8
2.4
SW56
No rate selection
Shown with 9.6 kbps Secondary Channel
selected. Two positions do not have rates
associated with them. The D4-OCU DP will not
function when these switch positions are set.
Figure 2. Rate Option Switch
There are restrictions in the deployment of
38.4, 56, and 64 kbps with error correction in
a D4 bank. When the dataport is configured for
no error correction, a single timeslot is used
and the unit may be located in any channel slot
of the D4 bank. With 38.4, 56 and 64 kbps error
correction selected, the dataport generates a
parity byte for each data byte, thus occupying
two timeslots. If the standard D4 38.4, 56 and
64 kbps error correction option is selected, the
parity byte is inserted into the timeslot
immediately following the data. The specific
design of the D4 common equipment interacts
with the error correcting schemes and yields
the following deployment restrictions on a
38.4, 56 and 64 kbps dataport with error
correction:
a. All D4 Modes: Dataport may not be located
in channel slot 24.
b. D4 Modes 1, 2: Data and parity must be
confined to groups of six channel slots (i.e.,
slots 1-6, 7-12, 13-18, or 19-24.)
No rate selection
64
56
38.4
19.2
9.6
4.8
2.4
61107.005L2-5C
Advertisement
