Dell Latitude D631 User Manual page 85

H -
A R D D I S K D R I V E C O N F I G U R A T I O N E R R O R
computer, remove the hard drive (see "Hard drive problems" on page 82), and boot the computer from a
CD. Then shut down the computer, reinstall the hard drive, and restart the computer. Run the Hard-
Disk Drive tests in the Dell Diagnostics (see "Dell Diagnostics" on page 77).
H -
A R D D I S K D R I V E C O N T R O L L E R F A I L U R E
computer. Shut down the computer, remove the hard drive (see "Hard drive problems" on page 82), and
boot the computer from a CD. Then shut down the computer, reinstall the hard drive, and restart the
computer. If the problem persists, try another drive. Run the Hard-Disk Drive tests in the Dell
Diagnostics (see "Dell Diagnostics" on page 77).
H -
A R D D I S K D R I V E F A I L U R E
down the computer, remove the hard drive (see "Hard drive problems" on page 82), and boot the
computer from a CD. Then shut down the computer, reinstall the hard drive, and restart the computer. If
the problem persists, try another drive. Run the Hard-Disk Drive tests in the Dell Diagnostics (see "Dell
Diagnostics" on page 77).
H -
A R D D I S K D R I V E R E A D F A I L U R E
the hard drive (see "Hard drive problems" on page 82), and boot the computer from a CD. Then shut
down the computer, reinstall the hard drive, and restart the computer. If the problem persists, try another
drive. Run the Hard-Disk Drive tests in the Dell Diagnostics (see "Dell Diagnostics" on page 77).
I
N S E R T B O O T A B L E M E D I A
bootable CD.
I
N V A L I D C O N F I G U R A T I O N I N F O R M A T I O N
information does not match the hardware configuration. The message is most likely to occur after a
memory module is installed. Correct the appropriate options in the system setup program (see "System
Setup Program" on page 107).
K
E Y B O A R D C L O C K L I N E F A I L U R E
Controller test in the Dell Diagnostics (see "Dell Diagnostics" on page 77).
K
E Y B O A R D C O N T R O L L E R F A I L U R E
computer, and avoid touching the keyboard or the mouse during the boot routine. Run the Keyboard
Controller test in the Dell Diagnostics (see "Dell Diagnostics" on page 77).
K
E Y B O A R D D A T A L I N E F A I L U R E
Controller test in the Dell Diagnostics (see "Dell Diagnostics" on page 77).
K
E Y B O A R D S T U C K K E Y F A I L U R E
the computer, and avoid touching the keyboard or keys during the boot routine. Run the Stuck Key test
in the Dell Diagnostics (see "Dell Diagnostics" on page 77).
M
E M O R Y A D D R E S S L I N E F A I L U R E A T A D D R E S S
faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them (see "Memory
Problems" on page 90.
M
E M O R Y A L L O C A T I O N E R R O R
system, another program, or a utility. Shut down the computer, wait 30 seconds, and then restart it. Try
to run the program again. If the error message still appears, see the software documentation.
The computer cannot identify the drive type. Shut down the
—
The hard drive does not respond to commands from the
0 —
The hard drive does not respond to commands from the computer. Shut
—
The hard drive may be defective. Shut down the computer, remove
—
The operating system is trying to boot to a nonbootable CD. Insert a
—
-
P L E A S E R U N
For external keyboards, check the cable connection. Run the Keyboard
—
For external keyboards, check the cable connection. Restart the
—
For external keyboards, check the cable connection. Run the Keyboard
—
For external keyboards or keypads, check the cable connection. Restart
—
,
R E A D V A L U E E X P E C T I N G V A L U E
The software you are attempting to run is conflicting with the operating
—
S S P
YS T E M E T U P R O G R A M
The system configuration
—
A memory module may be
—
Troubleshooting
85