Specifications - Hitachi h 45mry Handling Instructions Manual

DEMOLITION HAMMER SAFETY
WARNINGS
1. Wear ear protectors.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
ADDITIONAL SAFETY WARNINGS
1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
5. Before starting to break, chip or drill into a wall, fl oor or
ceiling, thoroughly confi rm that such items as electric
cables or conduits are not buried inside.
6. Even when the switch is on, the motor is running and
the tool head is pressed to the demolition surface, the
hammer sometimes does not start operating. In these
instances, turn the switch off , press the tool head against
the demolition surface again, and turn the switch on and
off . This should start the demolition hammer operating.
Repeat this procedure for several minutes, and the
demolition hammer will heat, after which it will operate
when switched to ON-LOCK.
7. When using tools such as bull points, cutters, etc.,
make sure to use the genuine parts designated by our
company.
8. Be sure to grip the handle and side handle during work.
Do not hold by the grip (A) during work. If you pull it by
mistake, the bull point could jump out.
9. RCD
The use of a residual current device with a rated residual
current of 30mA or less at all times is recommended.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
H45MRY : Demolition Hammer
Read all safety warnings and all instructions.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed in the below.
○ Case .............................................................................1
○ Bull Point (SDS-max shank) .........................................1
○ Side Handle ..................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
Demolishing concrete, chiseling off concrete, grooving, bar
cutting.
Application examples:
Installation of piping and wiring, sanitary facility installation,
machinery installation, water supply and drainage work,
interior jobs, harbor facilities and other civil engineering
works.

SPECIFICATIONS

Voltage (by areas)
Power Input
Full-load Impact Rate
Weight
(without cord, side handle)
NOTE
Due to HITACHI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Mounting a tool
Deciding working position of tool
Switch operation
How to use the demolition hammer*
3
English
(110 V, 120 V, 127 V, 220 V,
230 V, 240 V)
950 W
3000 min
-1
5.9 kg
Figure Page
1 85
2 85
3 85
4 85
1