Specifications - Makita 9556HP Instruction Manual

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Lock-off lever
2-2. Switch lever
2-3. Lock button
4-1. Wheel guard
4-2. Bearing box
4-3. Screw
5-1. Wheel guard
5-2. Bearing box

SPECIFICATIONS

Depressed center wheel diameter
Max. wheel thickness
Rated speed (n) / No load speed (n
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted
according to EN60745:
Model 9557HP
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model 9558HP
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Wear ear protection
Explanation of general view
5-3. Screw
6-1. Lock nut
6-2. Depressed center wheel/Multi-disc
6-3. Inner flange
7-1. Lock nut wrench
7-2. Shaft lock
8-1. Lock nut
8-2. Abrasive disc
8-3. Rubber pad
Model
Spindle thread
)
0
Overall length
Net weight
Safety class
noise level determined
) : 85 dB (A)
pA
) : 96 dB (A)
WA
) : 86 dB (A)
pA
) : 97 dB (A)
WA
9556HP
100 mm
6.4 mm
M10
11,000 min
273 mm
2.0 kg
ENE048-1
Vibration
The vibration
determined according to EN60745:
ENF002-2
Model 9557HP
Work mode : surface grinding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: disc sanding
ENG905-1
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model 9558HP
Work mode : surface grinding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode: disc sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
3
10-1. Wire cup brush/Wire bevel brush
11-1. Lock nut
11-2. Abrasive cut-off wheel/diamond
wheel
11-3. Inner flange
11-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
12-1. Exhaust vent
12-2. Inhalation vent
9557HP
115 mm
6.4 mm
M14 or 5/8"
(country specific)
-1 -1
11,000 min
273 mm
2.1 kg
/II
total value (tri-axial
) : 7.0 m/s
h,AG
2
) : 2.5 m/s
h,DS
2
) : 9.0 m/s
h,AG
2
) : 2.5 m/s
h,DS
2
9558HP
125 mm
6.4 mm
M14 or 5/8"
(country specific)
-1
11,000 min
273 mm
2.1 kg
ENG900-1
vector sum)
2
2
or less
2
2
or less
ENG902-1