Dmotion Detector Setting - Sanyo VCC-9400 Instruction Manual

CAMERA SETTINGS
MOTION detector setting
D
This function divides the monitor screen into 48 zones (8 x 6).
Based on information from the separate zones, target images that
show intruder movements are detected and an alarm is generated.
The degree of motion to be detected can be finely set.
Note:
•
Before activating this setting, use the system controller to select
a surveillance location that will not detect motion.
•
When SHUTTER speed is in LONG mode and IRIS SETTING
has SENSE UP activated, the MOTION function cannot be
turned ON.
1
In the MAIN MENU, select SET for CAMERA and press the
ENTER button.
The CAMERA SETTING screen will appear.
2
Use the joystick lever (j or l) to move the cursor to
VIEW SETTING, then press the ENTER button. (Ex: 1)
The VIEW SETTING 1 screen will appear.
ENTER
3
Use the joystick lever (j or l) to move the cursor to
MOTION, and then use the joystick lever (d or c) to
select ON. Then press the ENTER button.
The MOTION SETTING screen will appear and SET for SIZE
will be blinking.
ENTER
CAMERA SETTING
SYNC INT
PRIVACY MASK SET ‚
LENS SET ‚
VIEW SETTING 1 ‚
VIEW SETTING 1
IRIS AUTO ‚
WHITE BALANCE ATW ‚
SHUTTER OFF
MOTION ON ‚
APERTURE ON ‚
GAMMA ON
PRESET OFF
MENU BACK
MOTION SETTING
SIZE SET ‚
MASKING OFF
SENSITIVITY SET ‚
ZOOM OFF
INTERVAL 5S
– 36 –
MOTION SIZE setting
Sets the target object size desired for detection in the 48 zone
screen.
4
Press the ENTER button again.
The MOTION SIZE screen appears and the "1" for "V" will be
blinking.
ENTER
5
Set the size of the target object desired for detection
1
Determine the vertical size
Tilt the joystick lever to the right (c).
The "V" value (vertical pattern) will change to "2" and the
detection pattern will expand downward. Repeating this
motion will expand the pattern in the up and down
direction. Tilting the joystick lever to the left will reduce the
pattern size.
MOTION SIZE MOTION SIZE
V 1
H 1
PRESET OFF PRESET
MENU BACK MENU
V 1, H 1 V 2, H 1
MOTION SIZE MOTION SIZE
V 2
H 2
PRESET OFF PRESET
MENU BACK MENU
V 2, H 2 V 2, H 3
MOTION SIZE MOTION SIZE
V 1
H 2
PRESET OFF PRESET
MENU BACK MENU
V 1, H 2 V 1, H 3
2
Determine the horizontal size
Use the joystick lever (l) to move the cursor to the
"1" for "H", then tilt the joystick lever to the right (c).
The "H" value (horizontal pattern) will change to "2" and the
detection pattern will expand to the left. Repeating this
motion will expand the pattern in the left and right direction.
Tilting the joystick lever to the left will reduce the pattern size.
6
Canceling a settings screen
•
Use the joystick lever (l) to select BACK for MENU, then
press the ENTER button. The MOTION SETTING screen
will reappear.
•
To return to the normal screen, use the joystick lever (l
c) to select END for MENU, then press the ENTER button.
MOTION SIZE
V 1
H 1
PRESET OFF
MENU BACK
MOTION SIZE
V 2 V 6
H 1 H 1
OFF PRESET OFF
BACK MENU BACK
V 6, H 1
MOTION SIZE
V 2 V 3
H 3 H 3
OFF PRESET OFF
BACK MENU BACK
V 3, H 3
MOTION SIZE
V 1 V 1
H 3 H 8
OFF PRESET OFF
BACK MENU BACK
V 1, H 8
English