Bryston 14B SST Owner's Manual
  1. Manuals
  2. Brands
  3. Bryston Manuals
  4. Amplifier
  5. 14B SST C Series
  6. Owner's manual

Bryston 14B SST Owner's Manual

Sst series
Hide thumbs Also See for 14B SST:
Table of Contents

Advertisement

Quick Links

BRYSTON
OWNER'S MANUAL
Instructions For Bryston
SST Series Amplifiers
Model 14B SST

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 14B SST and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bryston 14B SST

Summary of Contents for Bryston 14B SST

  • Page 1 BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Model 14B SST...

  • Page 2: Table Of Contents

    Master Circuit -Breaker AC Power Input Local/Auto Switch Local/External Switch Block Diagrams Typical Performance Graphs Technical Specifications Important Warranty Information 14B SST Series Amplifier Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7-10 Page 11...

  • Page 3: General Introduction

    Before plugging in the power cord be sure your 14B SST amplifier is specified for the correct a/c voltage for your locali- ty. The voltage is listed on the label found at the upper right of the rear panel. The circuit feeding the 14B SST should be sufficient so as not to cause the circuit breaker to trip (15 amp min).

  • Page 4: Rear Panel Input Settings/Connections

    AC power or speaker cables. 4. Level Control. (pro models only) The level control will attenuate the input signal level from 0dB through -14dB. Rear Panel Input / Output Connections Fig 1 14B SST Series Amplifier...

  • Page 5: Output Binding Posts

    2. Spade lugs provide high contact area and secure fastening. Lugs should be gold plated. See diagram for details. Post diameter is 5/16’ ( 8mm ), lug width 5/8” (16 mm). Gold plated spade lugs are available from Bryston. 3. Stripped bare wire up to 3 gage can be inserted through the hole in the binding post and held in place by tightening the post knob.

  • Page 6: Front Panel Description

    Clipping occurs when the channel output level no longer can follow the level increase at the input (Overdriven input con- dition). When the 14B SST is driven into clipping the LED will change from green to red then back to green when the level is reduced ( Flashing Red ).

  • Page 7: Power Control Panel

    ‘OUT’ terminals is interrupted. . In the“Local” setting of switch (4) the 14B SST amplifier will ignore the control voltage, and power up only by using the front panel ‘SST POWER’ switch, or as in section 3 above. If a control voltage is present at the ‘IN’ terminals it will still be available at the ‘OUT’...

  • Page 8: Block Diagrams

    14B SST Series Amplifier...

  • Page 9: Typical Performance Graphs

    14B SST Series Amplifier Typical Band-pass Noise Power supply artifacts are all below -95 dBu BAL+6db input shown dBu: dB relative to a reference of 0.7746 Volts Typical THD+N Harmonic Content The harmonic content of the 14B SST is all even order.
  • Page 10 14B SST Series Amplifier Typical Frequency Response 14BSST 8 ohm 600w 4 ohm 900w Typical Phase Response 4 ohm 900w 8 ohm 600w...
  • Page 11 14B SST Series Amplifier Typical THD+N Sweep Graph shows that distortion is essentially unaffected by load. BAL+6db input shown. 4 ohm 900w 8 ohm 600w Typical IMD Sweep 4 ohm 900w 8 ohm 600w...
  • Page 12 14B SST Series Amplifier Damping Factor 8 ohm reference...

  • Page 13: Technical Specifications

    Max. Heat Dissipation - Output @ 600W @ 8 ohms - Max. Heat Dissipation 8 ohms - Output @ 900W @ 4 ohms - Max. Heat Dissipation 4 ohms - 14B SST Series Amplifier 215 Watts 733 Btu/Hr. 1284 Watts 2333 Btu/Hr.
  • Page 14 Bryston. In the event of a defect or malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance.

Table of Contents

Save PDF