Brother PT-1160 Martha By Mail User Manual

SKU HPT003
PT-1160
USER'S GUIDE
LA6618001
Printed in China
GENERAL PRECAUTIONS
• Use only Brother TZ tapes with this machine. Do not use any other tapes.
• Tapes are available in three different widths: 1/4"(6 mm), 3/8"(9 mm) and 1/2"(12 mm).
• Do not pull the tape since this may damage the tape cassette.
• Do not attempt to cut the tape while printing or feeding since this will damage the
tape.
• Do not clean the machine with alcohol or other organic solvents. Use only a soft, dry
cloth.
• Remove the batteries and disconnect the AC adapter if you do not intend to use the
machine for an extended period of time.
Note: If power is disconnected for more than three minutes, all text shown in the
display and any text files stored in the memory will be lost.
• Do not put any foreign objects into or anything on the machine.
• Do not expose the machine to high temperatures or high humidity. Never leave it on
the dashboard or in the back of your car.
• Do not use the machine in dusty places, and keep it out of both direct sunlight and
rain.
• Do not leave any rubber or vinyl on the machine for an extended period of time.
Doing so may cause staining.
• After inserting a new tape cassette, advance the tape by holding down
pressing once.
• Do not touch the print head mechanism. If the head is touched, clean it immediately
with a soft wipe (e.g., a cotton swab) to avoid permanent damage.
• To avoid injuries, do not touch the cutter's edge.
• Use only the AC adapter designed exclusively for this machine. Use of any
other adapter will void the warranty.
Please contact your Brother dealer for details.
POWER SUPPLY
Changing the batteries
CAUTION
Batteries installed incorrectly can overheat and leak. Can result in chemical burns
and machine overheating and damage.
Your machine requires 6 alkaline AAA batteries.
Carefully follow these instructions.
1 Press bumps on top of back cover and open.
2 Pull out tape cassette, if one was installed.
3 Remove batteries, if they were already installed.
4 Hold machine as pictured:
FIRST, in
5 Insert six new batteries as follows:
LOWER layer
Always:
insert ˝+˝ ends
pointing DOWN.
• Insert "+" ends before "-" ends.
-
• Remove "-" ends before "+" ends.
• Replace all 6 batteries at the same time with new ones.
+
6 Insert tape cassette.
7 Insert two hooks on bottom end of back cover into slots on bottom
of machine. Push down firmly on cover until it snaps into place.
8 Turn machine on.
If no power, immediately remove batteries and call Brother Customer Service at:
1-877-478-6824
Optional AC adapter
The AC adapter allows you to use this machine wherever an electrical outlet is available.
Use Brother's AD-30 adapter for your new PT-1160.
1 Insert the plug on the adapter cord into the adapter
jack on the bottom end of the machine.
2 Insert the plug into the nearest standard electrical outlet.
OVERVIEW
Tape cutter lever
Display
Backspace key
Return key
Function dial
Back cover
Caps key
Num key On/Off key
Batteries
Tape cassette
TAPE CASSETTES
A TZ tape cassette is supplied with this unit. The Brother TZ tapes used with this machine are
available in a variety of colors and three tape widths (1/4"(6 mm), 3/8"(9 mm), 1/2"(12 mm)).
1 Press in on the rough area at the top end of the machine and
fold open the back cover.
2 If a tape cassette is already installed, remove it by pulling it
straight up.
3 If the ink ribbon in the other tape cassette is loose, use your
finger to wind the toothed wheel in the direction of the arrow on
the cassette until there is no slack in the ribbon. Also, make sure
that the end of the tape feeds under the tape guides.
Note: If you are using a new tape cassette provided with a
stopper, be sure to remove the stopper.
4 Insert the tape cassette firmly into the compartment, making
sure that the entire back of the cassette contacts the bottom of
the compartment.
Note: When inserting a tape cassette, make sure that the inner
ribbon does not catch on the corner of the metal guide.
5 Securely close the back cover, making sure that it snaps into place.
and
6 Feed the tape by holding down and pressing
then push in the tape cutter lever to cut the tape.
LETTERING STICK
The enclosed lettering stick enables you to easily remove the backing from labels printed
on laminated tapes.
1 Hold the tape in your left hand, with the printed surface facing up, and hold the stick
in your right hand.
2 Pass the tape halfway through the long narrow hole in the stick.
3 Turn the stick three-quarters of a turn towards you and pull the stick away from you
as shown below.
4 Peel off the label backing.
STARTING
Press . If batteries have been installed or the machine has been plugged in using the
optional AC adapter, the previous session's information is displayed when the machine is
SECOND, in
UPPER layer
turned on. This feature allows you to stop work on a label and turn off the machine, then
insert ˝+˝ ends
return to it later without having to re-enter the text.
pointing UP.
The machine automatically turns off if no key is pressed within five minutes. The current
+
session's information is stored in the machine's internal memory and displayed when the
-
machine is later turned on again.
CODE KEY
By holding down and pressing a key with a function, character or accent written
above it, you can use the corresponding function or add the corresponding character to
your text.
CAPS KEY
By pressing to enter Caps mode, you can add upper-case letters to your text by
simply pressing the character keys. When this mode is on, the Caps indicator in the top-
left corner of the display comes on. To exit Caps mode, press
indicator goes off.
NUM KEY
By pressing to enter Num mode, you can add numbers to your text by simply
pressing the corresponding keys. When this mode is on, the Num indicator in the bottom-
left corner of the display comes on. To exit Num mode, press
goes off.
DISPLAY
This machine's LCD shows one row of 8 characters; however, the text that you enter can
be up to 55 characters in length. The 8-character display is like a window which moves
across the text.
Print head
1234567890123456789012345678901234567890123456789012345
Tape exit slot
CURSOR MOVEMENT
You can view and edit different parts of the text by moving the cursor backward and
forward.
G
To move the cursor one character at a time, press
G
To move the cursor to the beginning of the text, hold down
G
To move the cursor to the end of the text, hold down
BACKSPACE KEY
This key can be used to remove characters from your text, clear all of the text or cancel
functions.
G
To delete the character to the left of the cursor or to cancel a function (instead of
pressing ), press .
G
To clear all of the text that is currently entered, hold down
SPACE KEY
once, and
As on a word processor, press
RETURN KEY
Press when you wish to select a setting, or end the first line of text and start the
second.
G
To add a second line, press
indicate the end of the first line and the beginning of the second.
Note: Two lines of text can only be entered if 3/8"(9-mm) or 1/2"(12-mm)-wide tape
is installed.
G
To select an item from a list, press
ACCENTED CHARACTERS
You can also choose from a list of other accented characters that can be added to your text.
Letter Accented character
A À Á Ä Â Ã Æ
C Ç
E È É Ë Ê
I Í Ï Î
N Ñ
O Ó Ö Ô Õ
U Ù Ú Ü Û
1 Press
if you want the accented character to be an upper case letter.
Note: To quit the following procedure at any time without making any changes, press
2 Hold down and press . The message "A-U?" appears in the display.
3 Turn the Function dial until the cursor is positioned under the desired accented
character.
OR
Press the key for the letter in the accented character that you wish to add, and then
press and until the cursor is positioned under the desired accented
character.
4 Press the Function dial (or ) to add the selected character to your text.
until the Caps
SYMBOLS
In addition to the letters, symbols, and numerals on and above the keys, there are 72
symbols available with the Symbol function. These symbols are divided into 10 groups,
corresponding to the letters A through I.
until the Num indicator
Group
A Ü ü
B í ó
C Õ õ
°
D ·
E $ ¢
F TM
4
G
H
← →
I
1 Press . The message "A-I?" appears in the display.
2 Press the key for the letter of the group containing the symbol that you wish to add,
and then press and until the cursor is positioned under the desired symbol.
3 Press to add the symbol to the text.
or .
and press .
and press .
and press .
to add a blank space to your text.
once. The return mark ( ) appears in the text to
once.
Letter Accented character
a à á ä â ã æ
c ç
e è é ë ê
i í ï î
n ñ
o ó ö ô õ
u ù ú ü û
.
Symbols
Ç ç Æ æ á é
#
ú Ã ã
Ñ ñ ¡ ¿ § #
×
; % + ÷ =
[ ] 2 3
2 3
® ©
↑ ↓
_ ~