Subscribe to Our Youtube Channel
Related Manuals for BinTec XGeneration X2301
Summary of Contents for BinTec XGeneration X2301
- Page 1 UICK NSTALL UIDE © Copyright April 28, 2005 Funkwerk Enterprise Communications GmbH Bintec User’s Guide - XGeneration Version 1.3...
- Page 2 Purpose This document is part of the user’s guide to the installation and configuration of Bintec gateways run- ning software release 7.1.15 resp. 7.1.19 for WLAN or later. For up-to-the-minute information and in- structions concerning the latest software release, you should always read our Release Notes, especially when carrying out a software update to a later release level.
-
Page 3: Table Of Contents
Support Information ........19 Quick Reference Bintec User’s Guide... - Page 4 Bintec User’s Guide Quick Reference...
-
Page 5: Introduction
Wizard. Detailed knowl- edge of networking is not necessary. A detailed online help system gives you extra support. BRICKware includes helpful applications for the management of your gate- way. Congratulations on your new purchase and have fun! Quick Reference Bintec User’s Guide... - Page 6 Introduction Bintec User’s Guide Quick Reference...
-
Page 7: Taking Into Operation
Gateway into operation. These are supplied together with the Note gateway. The current version is also available at www.funkwerk-ec.comt. Connections All connections on X2301, X23020, X2301w X2302w are located at the rear of the unit. Quick Reference Bintec User’s Guide... -
Page 8: Setting Up And Connecting
Place your gateway on a firm, level base. Orient the antenna. Serial connection: Connect the serial port of your PC (COM1 or COM2) to the serial port of your gateway. Use only the serial cable supplied with the Bintec User’s Guide Quick Reference... - Page 9 LAN interfaces using further Ethernet cables. 8. Mains supply: Connect your gateway to a mains socket using the mains adaptor supplied. The gateway is now prepared for configuration using the HTML Wizard. Quick Reference Bintec User’s Guide...
- Page 10 Taking into Operation Bintec User’s Guide Quick Reference...
-
Page 11: Configuration
SER NAME ■ : bintec ASSWORD All Bintec gateways are shipped with the same user names and pass- words. As long as the password remains unchanged, they are not protect- ed against unauthorized use. Attention! Change the passwords to prevent unauthorized access to your gateway! (See Bintec User’s Guide chapter Access and Configuration.) -
Page 12: In Advance Of Configuration
Configuration cable, carry out a software update is described in the Bintec User’s Guide chapter Gateway Management (in the Basics section). WLAN As WLAN uses the air as transmission medium, the transferred data can theo- retically be intercepted and read by anyone with the respective means. Thus, safeguarding the radio link is to be paid special attention. - Page 13 Access data Example Your value Provider name GoInternet Protocol PPP over Ethernet (PPPoE) Encapsulation bridge-no-fcs VPI (Virtual Path Identifier) VCI (Virtual Circuit Identifier) Your user name MyName Password TopSecret Table 3-2: Data for Internet access Quick Reference Bintec User’s Guide...
-
Page 14: Configure The Pc
First click Properties, then Install in the status window of the LAN Connection. Select the Protocol entry. Click Add. Select Internet Protocol (TCP/IP) and click OK. Follow the instructions on the screen and finally restart your PC. Bintec User’s Guide Quick Reference... -
Page 15: Installing Brickware
The PC now has an IP configuration and can access the Internet via the gate- way. 3.1.3 Installing BRICKware BRICKware contains a number of programs to help you when working with your gateway. The installation is optional. Quick Reference Bintec User’s Guide... - Page 16 Proceed as follows to install the software: Close all Windows programs on your PC. Place your Bintec Companion CD in the CD-ROM drive of your PC. The Start window appears automatically after a short time. If the Start window does not open automatically, click your CD-ROM drive in Windows Explorer and double-click setup.exe.
-
Page 17: Configuring The Gateway
If you have already created a configuration with the Wizard, the Wizard can use the preset values. You are informed about this possibility during configura- Note tion. The configuration of your gateway is started as follows: 1. Select Installation on the Bintec Companion CD and click the button Configure Gateway. Quick Reference... - Page 18 Wizard) with any current Web browser (java script must be activated). HTML Setup Tool can also be opened with any current Web browser (java script must be activated). Enter 192.168.0.254/setup to start a Setup Tool ses- sion. Bintec User’s Guide Quick Reference...
-
Page 19: Testing The Configuration
To access the status page, just enter 192.168.0.254 in your Web browser. Other means of access and configuration information are described in the chap- ter Access and Configuration of the Bintec User’s Guide (as a part of the Ba- sics section). Testing the Configuration You have completed the configuration of your gateway and can now test the connection in your LAN and to the Internet. - Page 20 Configuration Bintec User’s Guide Quick Reference...
-
Page 21: Support Information
Support Information Contact numbers and addresses of the Bintec Support Center of Funk- werk Enterprise Communications GmbH: Germany Available from monday till friday 9 a.m. - 5 p.m. (CET) Switzerland ■ First Level Support: Austria – Telephone: 00 800 7333 7333... - Page 22 Available from monday till friday 9 a.m. - 5 p.m. (CET) ■ Second Level Support: Telephone: +49 - 911 9673 1550 or +49 - 180 300 91 91 550 Fax: +49 - 911 9673 1599 or +49 - 180 300 9191 599 E-Mail: support@funkwerk-ec.com Bintec User’s Guide Quick Reference...
Need help?
Do you have a question about the XGeneration X2301 and is the answer not in the manual?
Questions and answers