ALTA BLISS Quick Start Manual

Declarations

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development
Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device. Le présent appareil est conforme aux CNR d'ISED
applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.

FCC SAR Warning:

RF Exposure Information (SAR): The SAR limit of USA (FCC)is 1.6W/Kg averaged
over one gram of tissue.
Product Type: BLISS Bridge (FCC ID: 2AU29AMPRFWIFIUSB) has also been tested
against this SAR limit. The device was tested for typical body-worn operations to
keep the BLISS Bridge at least 5mm from the body. When worn on body must be
correct back clip for this product, use of non-approved accessories may result in
exposure levels which exceed the uncontrolled environmental RF exposure limits.
FCC SAR Warning:
The SAR limit of IC is 1.6W/Kg averaged over one gram of tissue.
Product Type: BLISS Bridge, model number: BLISS Bridge Wifi and RF (IC:
25624-AMPRFWIFI) has also been tested against this SAR limit. The device was
tested for typical body-worn operations to keep the BLISS Bridge at least 5mm
from the body. When worn on body must be correct back clip for this product,
use of non-approved accessories may result in exposure levels which exceed the
uncontrolled environmental RF exposure limits.
Le SAR de IC est limité à 16w / kg, avec une moyenne par gramme. Produits Type:
BLISS Bridge, type: BLISS Bridge Wifi and RF (IC: 25624-AMPRFWIFI) a également
été testé pour la limite SAR. Ce dispositif est utilisé pour tester des opérations d
'usure corporelle typiques et des opérations en direction du Haut de physique,
de manière à maintenir une distance d' au moins 5mm entre le BLISS Bridge et le
visage. Osure.`
AMP USB Bridge allows the user to link their motorized
and Draperies into a Wi-Fi network, enabling control via smart APP
interaction with other IoT products.
S tep 1 Down loa d A PP
P lease scan the QR c ode below .
BLISS BRIDGE
QUICK START GUIDE
St ep 2
Please scan the QR c ode below to learn more about linking the AMP USB Bridge
with your home Wi-Fi router, setting up the AMP APP, and
with other IoT applications.
Quick Start Guide for
AMP USB Bridge
Product
Certi cation
The BLISS Bridge allows users to link their motorized shades and blinds into a Wi-Fi
network enabling control via smart APP and interaction with other IoT products.
AMP USB Bridge allows the user to link their motorized
Step 1
Please scan the QR Code below to download the BLISS app.
TM
Quick Start Guide for
AMP USB Bridge
Scan the QR code to
Product
Certi cation download the app on
on the Apple Store.
AMP USB Bridge allows the user to link their motorized
and Draperies into a Wi-Fi network, enabling control via smart APP
interaction with other IoT products.
S tep 1 Down loa d A PP
St ep 2
P lease scan the QR c ode below .
Please scan the QR c ode below to learn more ab
with your home Wi-Fi router, setting up the AMP A
Scan the QR code to
with other IoT applications.
get the app on
Google Play.

Step 2

Please scan the QR Code below for additional videos on linking the BLISS
St ep 2
Bridge with your home Wi-Fi router, setting up the BLISS app, and establishing
Please scan the QR c ode below to learn more about linking the AMP USB
a connection with other IoT applications.
with your home Wi-Fi router, setting up the AMP APP, and
with other IoT applications.
S hades , B linds,
S hades , B linds,
and
S hades , B li
establishing a connection
establishing a