Table of Contents
Advertisement
Quick Links
Anderic
Note: This Anderic remote is meant to serve as a replacement for the original
Hunter
remote control and will only work with the original Hunter
®
Anderic does not provide the receiver that goes with this remote. If a new receiver is
needed, we suggest purchasing the entire kit from Anderic.com/RR7079TKIT,
Part number: RR7079TKIT. This kit will work the same and carries a 1-Year
Manufacturer warranty*.
Installation of the original Hunter
separately): We do not provide the instructions, please refer to the installation guide
that was originally provided with your Hunter
Installing or changing the battery
To access the battery compartment, remove the screw that secures the battery
cover. Install or replace the battery with a new CR2032 battery. The battery should
be installed with the positive (+) side up.
Pairing instructions:
1. While the power to the fan is on, use the pull-chain switch on the fan to set
the fan speed to the HIGH position before proceeding.
2. Turn power off to the fan, either by the wall switch or by the circuit box.
3. Within 3 minutes of restoring power to the fan, press both the Fan Off button
and the High button for at least 4 seconds. The fan will turn on low to
indicate successful syncing. If it does not, turn off power to the fan, wait 1
minute then try again. If using the transmitter with multiple fans, repeat this
process for each.
Installing the wall mount:
To install the wall mount, remove the two screws holding your light switch cover
plate. Do not remove the cover plate entirely. Orient the cradle by lining up the two
mounting holes with those on the cover plate. Insert and tighten the screws. Do not
over tighten.
Safe-Exit
The Safe-Exit Program gives you about thirty seconds of light when you turn the
lights off to exit the room before the lights go out. To use Safe-Exit:
• Press the Fan Off button for at least three seconds to initiate the Safe-Exit
Mode.
• The lights will flash for visual confirmation.
• The lights will stay on 50% (incandescent bulbs only) brightness for 15
seconds and then begin to dim. After a total of 30 seconds, the lights will be
completely off. If CFL or non-dimmable LED bulbs are installed, the lights will
stay at 100% brightness for 30 seconds before turning completely off.
Universal 3 Speed Ceiling Fan Remote
®
Models: 99122, 99119
Receiver unit (if not already installed, sold
®
Universal Ceiling Fan Remote Kit.
®
receiver units.
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Anderic 99122
Summary of Contents for Anderic 99122
- Page 1 Anderic Universal 3 Speed Ceiling Fan Remote ® Models: 99122, 99119 Note: This Anderic remote is meant to serve as a replacement for the original Hunter remote control and will only work with the original Hunter receiver units. ® ® Anderic does not provide the receiver that goes with this remote. If a new receiver is needed, we suggest purchasing the entire kit from Anderic.com/RR7079TKIT, Part number: RR7079TKIT. This kit will work the same and carries a 1-Year Manufacturer warranty*. Installation of the original Hunter Receiver unit (if not already installed, sold ® separately): We do not provide the instructions, please refer to the installation guide that was originally provided with your Hunter Universal Ceiling Fan Remote Kit. ® Installing or changing the battery To access the battery compartment, remove the screw that secures the battery cover. Install or replace the battery with a new CR2032 battery. The battery should be installed with the positive (+) side up. Pairing instructions: 1. While the power to the fan is on, use the pull-chain switch on the fan to set the fan speed to the HIGH position before proceeding. 2. Turn power off to the fan, either by the wall switch or by the circuit box. 3. Within 3 minutes of restoring power to the fan, press both the Fan Off button and the High button for at least 4 seconds. The fan will turn on low to indicate successful syncing. If it does not, turn off power to the fan, wait 1 minute then try again. If using the transmitter with multiple fans, repeat this process for each. Installing the wall mount: To install the wall mount, remove the two screws holding your light switch cover plate. Do not remove the cover plate entirely. Orient the cradle by lining up the two mounting holes with those on the cover plate. Insert and tighten the screws. Do not...
- Page 2 Remote control of fan is erratic • Make sure the battery is installed correctly. • Install a fresh battery. Transmitter only works when held at close range • Change battery. Lights do not dim • Check to see if a CFL bulb or non-dimmable LED bulb is installed. The control has a feature that automatically detects CFL/LED bulbs and turns off dimming if a CFL bulb is installed. Incandescent bulbs work the best for dimming. CFL bulbs flicker • Make sure the lights are not dimmed. Turn lights on using the light key, then press and hold light key until bulb is fully bright and no longer flickers. • Turn the light switch off and back on. Within three minutes, hold down the Fan Off button while pressing the Light button twice. If the problem is not corrected, repeat the process up to three times. For customer support and warranty claims*: Visit us at anderic.com Call us at 1-855-263-3742 *Anderic 1-Year Limited Warranty Information: Anderic (Dan’s Electronics Etc., Inc.) makes the following limited warranty to the original purchaser of the Control (“Control”): Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale. If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL, THIS WARRANTY AND ANY IMPLIED WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH CONTROL. This warranty excludes malfunctions or failures which were caused by repairs by persons not authorized by us, mishandling, improper installation, modifications, or damage to the Control while in your possession or unreasonable use. This warranty does not apply to batteries or to deterioration or damage to the product caused by the use of faulty batteries. To obtain a replacement, return your Control postage prepaid along with proof of purchase to Anderic Warranty Department at 4945 Reynolda Road, Winston Salem, NC 27106. IN NO EVENT SHALL ANDERIC BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS...
Need help?
Do you have a question about the 99122 and is the answer not in the manual?
Questions and answers