Sleep Timer; Energy Saving Operations; Economy Operation; Other Operations - Fujitsu ASYG07KMTB Operating Manual

6.3. Sleep timer

The Sleep timer supports your comfortable sleep by moderating the air
conditioner operation gradually.
1. Press .
( )
2. Press to set the time until the operation
stops.
Each time you press the button, the time changes as follows:
0H 1H 2H
30M 00M 00M
(30 min.)
NOTES: If you do not press any buttons for 5 seconds, the remote
controller display returns to the standby screen.
• The setting time is kept even if the Sleep timer finishes. To repeat
the Sleep timer, press
remote controller display.
• To deactivate the Sleep timer, press
on the remote controller display.
The indicator will disappear.
During the Sleep timer operation, the setting temperature changes as
the following figure.
In Heating mode
1 °C 2 °C 3 °C 4 °C
30 min.
1 hour
1.5 hour
Set time
After the set time has elapsed, the air conditioner operation turns off.
NOTES: If you set the On timer or Off timer after setting the Sleep
timer, the Sleep timer is canceled.
7. ENERGY SAVING OPERATION

7.1. Economy operation

It saves more electricity than other operation modes by changing the set
temperature to a moderate setting.
) )
Press to activate/deactivate the Economy
operation.
[ ] indicator on the indoor unit will turn on.
Operation
mode
Cooling/Dry Few degrees higher than the set temperature
Heating Few degrees lower than the set temperature
NOTES:
• In the Cooling, Heating, or Dry mode, the maximum output of this
operation is approximately 70 % of usual operation.
• This operation cannot be performed during the temperature
monitoring by the Auto mode.
3H 5H 7H 9H
00M 00M 00M 00M
hours
while is not shown on the
while is shown
In Cooling or Dry mode
Set time
Set
1 hour
temperature
1 °C 2 °C
Room temperature

8. OTHER OPERATIONS

8.1. Powerful operation

In the Powerful operation, the air conditioner will operate at maximum
power and strong airflow to cool down or warm up the room quickly.
NOTES: In multi connection, this function cannot be used.
) )
Press to activate/deactivate the Powerful operation.
When activated, the indoor unit will emit 2 short beeps.
When deactivated, the indoor unit will emit 1 short beep.
The Powerful operation will be turned off automatically in the following
situations:
• The Powerful operation runs for a certain amount of time and the
room temperature reaches the set temperature in the Cooling, Dry,
or Heating mode.
• 20 minutes after the Powerful operation has started.
NOTES:
• The airflow direction and the fan speed are controlled automatically.
• The Powerful operation cannot be performed simultaneously with
Economy operation.
• The Powerful operation overrides the following operations. If
the following operations are set, they will start after the Powerful
operation finishes.

- Outdoor Unit Low Noise operation

- Energy Saving program
• If the wired remote controller (optional) is connected, this function is
restricted.
8.2. Outdoor Unit Low Noise operation
The Outdoor Unit Low Noise operation lowers noise from the outdoor
unit. During this operation, the rotation number of the compressor
decreases and the outdoor unit fan rotates slowly.
NOTES: In multi connection, this function cannot be used.
) )
Press to activate/deactivate the Outdoor Unit Low
Noise operation.
While the Outdoor Unit Low Noise operation is activated,
on the remote controller is displayed.
The setting is preserved even if the air conditioner is turned off.
NOTES:
• This operation cannot be performed simultaneously with the Fan
mode, Dry mode, and Powerful operation.
• If the wired remote controller (optional) is connected, this function is
restricted.
8.3. 10 °C Heat operation
10 °C Heat operation maintains the room temperature at 10 °C so as to
prevent the room temperature to drop too low.
to activate the 10 °C Heat operation.
) )
Press
The indoor unit will emit 1 short beep and [
indoor unit will turn on.
) )
Press to turn off the air conditioner.
[ ] indicator will turn off.
NOTES:
• During the 10 °C Heat operation, only
• When the room temperature is warm enough, this operation will not
perform.
• If the wired remote controller (optional) is connected, this function is
restricted.
] indicator on the
is valid.
En-6