Important safety instructions S a f e t y PLEASE READ THE SAFETY INSTRUCTIONS CAREFULLY • Read the instructions. • Keep these instructions. • Follow all instructions. • Do not use the UniStop in water. • Be careful not to drop it on the ground. •...
Contents C o n t e n t s IMPORTANT SAFETY INSTRUCTIONS STOP WATCH ANALYZE CONTENTS ANALYZE POPUP MENU COPYRIGHT AND ACKNOWLEDGEMENTS IV MORE INFO SCREEN SALES AND SERVICE IN DENMARK MAIN MENU INTERNATIONAL DEALERS TRANSFERRING DATA DESIGN AND PRODUCTION SETUP MENU ABOUT THIS USER GUIDE CLOCK SETUP...
I n t r o d u c t i o n Introduction This User Guide contains all relevant information about your new UniStop 4 channel stop watch. Get started with the UniStop in 2 minutes with the Quick Guide. Read all about the advanced features and functions in the Reference Guide.
MEMORY Large memory for 5000 BLUETOOTH laps or splits. Transfer data to the Near field communica- Unipro app on your tion for small data phone or tablet. transfer to your phone. DISPLAY BACKLIGHT Large graphical display...
Specifications I n t r o d u c t i o n Time range 0:00.00 to 9:59.99 Resolution 0.01 sec. Typical accuracy 20 ppm (0.002 %) Communication Bluetooth (BLE) and NFC Power supply 2 x AAA Alkaline batteries Battery lifetime ~ 150 hours* Languages DEN, FIN, FRA, GBR, GER, HUN, ITA, NED, NOR, POL, POR, SPA, SWE...
Q u i c k G u i d e Quick Guide Read the Quick Guide and learn how to use the basic functions of the UniStop: Turn UniStop on and off, taking lap and split times, analyze the times and how to clear laps. You will be ready to go in 2 minutes...
Quick guide Q u i c k G u i d e • Press and hold OK while turning UniStop • Choose “CLEAR LAPS” from the popup menu. • Press and hold down OK for 1 second from the stop watch screen. You always have to confirm by pressing OK except when using the first method.
Carrying bag Lithium batteries and the software is optimized A Unipro bag is included with UniStop. This to run using as little energy as possible. can be attached to your belt and offers a very good protection for your UniStop.
L1 to start the timing of driver one, L2 to your own name. The maximum number of for start the timing of driver two and so on. characters is 25. This is done from the Unipro You will see the corresponding stop watch app.
R e f e r e n c e Operating UniStop G u i d e To take split times, you use the S1 – S4 but- tons. One for each driver. You can take up to 8 split times per lap, but you are automatically getting a split from the last split point to the finish line.
R e f e r e n c e Operating UniStop G u i d e The menu line is showing the number 1,2,3. This is indicating that stop watch for driver 1, 2 and 3 are running. It could however be 1, 2, 3 or 4.
R e f e r e n c e Operating UniStop G u i d e ”BIG” 4 DRIVERS MODE button. This is to prevent you bringing up the menu if you wanted to press the L4 button If you are using 3 or 4 drivers a lot, we have instead.
R e f e r e n c e Operating UniStop G u i d e L1 to L4 for the driver you want to remove. Because there are already some laps measured in the memory, you will be able to do the When you have pressed the button long following.
R e f e r e n c e Operating UniStop G u i d e ANALYZE POPUP MENU While operating in analyze mode, you can bring up a popup menu. Information screen. MAIN MENU Stop watch analyze popup menu. From the main menu you can go to the diffe- rent menus or turn UniStop off.
Bluetooth is powered down, and the app is no “CONNECTABLE” means that UniStop is ready longer able to connect to UniStop. to connect to your phone running the Unipro App. After you connected the app to your UniStop, the following screen will be shown.
Some basic settings are in the setup menu. The easiest way is to connect UniStop to the Unipro app. Every time you connect UniStop to the app using Bluetooth, the clock will be synchronized with the clock in the phone. This way you always update the clock in UniStop to keep it accurate.
R e f e r e n c e Setup mode G u i d e press OK again to go back to the setup menu. and 100%. The backlight is not turned on and off with this setting. Please see “BACKLIGHT” on page 12.
R e f e r e n c e Setup mode G u i d e MULTISTART SETUP BIG FONT SETUP UniStop can start the stop watches in two UniStop will use a quite small font for 3 and ways. 4 drivers.
If you have any problems, either with the setup or with daily use, please check the following pages for suggested solutions. If you don’t find the answer to the problem here, please contact your Unipro dealer for further assistance. Weak and hard to read text App cannot connect to UniStop The contrast is set too low.
Maintenance M a i n t e n a n c e Battery change When assembling UniStop again, attach the rear part of the box again, and carefully To replace batteries tighten the screws. When the batteries reach 2.2 V, the low battery symbol will be shown at the top of the Do not over tighten the six screws.
M a i n t e n a n c e Service Guarantee The Unipro UniStop stop watch has been The product is guaranteed against defects in carefully designed to give you many years of material and workmanship for two years from untroubled use.
Index I n d e x Symbols Contrast too low 23 Copyright IV 1 driver mode 13 2 drivers mode 13 3 drivers mode 14 Dealers IV 4 drivers mode 14 Design ideas 5 Dimensions 7 Display 7, 11 Acknowledgements IV Alkaline batteries 24 Analyze mode 9, 16 Easy to use 5...
Page 27
Preface II Time range 7 Time synchronize 18 Transferring data 10, 18 Troubleshooting 23 Quick guide 9 Unipro homepage 10 Rain II User guide version IV Real time clock 6, 11 Reference guide 11 Remove driver 10, 16 Resolution 7...
Need help?
Do you have a question about the UniStop V2 and is the answer not in the manual?
Questions and answers