Table of Contents
Advertisement
5.1.3
5.1.3
5.1.3
Setting the RAID item in BIOS
Setting the RAID item in BIOS
Setting the RAID item in BIOS
5.1.3
5.1.3
Setting the RAID item in BIOS
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a
RAID set from SATA hard disk drives attached to the SATA connectors
supported by the Intel
1.
Enter the BIOS Setup during POST.
2.
Go to the M a i n M e n u > I D E C o n f i g u r a t i o n > S - A T A
M a i n M e n u > I D E C o n f i g u r a t i o n > S - A T A
M a i n M e n u > I D E C o n f i g u r a t i o n > S - A T A
M a i n M e n u > I D E C o n f i g u r a t i o n > S - A T A
M a i n M e n u > I D E C o n f i g u r a t i o n > S - A T A
C o n f i g u r a t i o n
C o n f i g u r a t i o n
C o n f i g u r a t i o n, then press <Enter>.
C o n f i g u r a t i o n
C o n f i g u r a t i o n
3.
Set the S A T A C o n t r o l l e r M o d e O p t i o n
S A T A C o n t r o l l e r M o d e O p t i o n
S A T A C o n t r o l l e r M o d e O p t i o n
S A T A C o n t r o l l e r M o d e O p t i o n item to [Enhanced], then
S A T A C o n t r o l l e r M o d e O p t i o n
press <Enter>.
4.
Set the S A T A R A I D E n a b l e
S A T A R A I D E n a b l e
S A T A R A I D E n a b l e
S A T A R A I D E n a b l e
S A T A R A I D E n a b l e item to [Enabled].
5.
Save your changes, then exit the BIOS Setup.
Refer to Chapter 4 for details on entering and navigating through the
BIOS Setup.
5.1.4
5.1.4
5.1.4
RAID configuration utilities
RAID configuration utilities
RAID configuration utilities
5.1.4
5.1.4
RAID configuration utilities
RAID configuration utilities
Depending on the RAID connectors that you use, you can create a RAID set
using the utilities embedded in each RAID controller. For example, use the
L S I L o g i c E m b e d d e d S A T A R A I D S e t u p U t i l i t y
L S I L o g i c E m b e d d e d S A T A R A I D S e t u p U t i l i t y
L S I L o g i c E m b e d d e d S A T A R A I D S e t u p U t i l i t y or the I n t e l
L S I L o g i c E m b e d d e d S A T A R A I D S e t u p U t i l i t y
L S I L o g i c E m b e d d e d S A T A R A I D S e t u p U t i l i t y
M a t r i x S t o r a g e T e c h n o l o g y if you installed Serial ATA hard disk drives
M a t r i x S t o r a g e T e c h n o l o g y
M a t r i x S t o r a g e T e c h n o l o g y
M a t r i x S t o r a g e T e c h n o l o g y
M a t r i x S t o r a g e T e c h n o l o g y
on the Serial ATA connectors supported by the Intel
Southbridge.
For DSBF-D/SAS model, you may use the L S I 1 0 6 8 S A S C o n f i g u r a t i o n
U t i l i t y
U t i l i t y
U t i l i t y if you installed SAS hard disk drives to the mini-SAS connector(s)
U t i l i t y
U t i l i t y
supported by the LSI1068 PCI-X SAS controller.
Refer to the succeeding sections for details on how to use each RAID
configuration utility.
A S U S D S B F - D S e r i e s
A S U S D S B F - D S e r i e s
A S U S D S B F - D S e r i e s
A S U S D S B F - D S e r i e s
A S U S D S B F - D S e r i e s
®
6321ESB Southbridge chip. To do this:
®
6321ESB
L S I 1 0 6 8 S A S C o n f i g u r a t i o n
L S I 1 0 6 8 S A S C o n f i g u r a t i o n
L S I 1 0 6 8 S A S C o n f i g u r a t i o n
L S I 1 0 6 8 S A S C o n f i g u r a t i o n
I n t e l
I n t e l
® ® ® ® ®
I n t e l
I n t e l
5 - 3
5 - 3
5 - 3
5 - 3
5 - 3
Advertisement
Table of Contents
