Advertisement
ATTACHING THE APPLICATOR TOP TO THE HAIR COLOR CREAM TUBE
1. Remove the cap from the Hair Color Cream Tube and set it aside for later use.
2. Screw the Hair Color Applicator Top to the Hair Color Tube.
3. Gently squeeze the Tube until color comes out of the sponge on the Applicator Top.
IMPORTANT NOTES: When finished coloring hair, remove and wash the Applicator Top
thoroughly and allow it to dry completely before using with another color or storing. DO NOT
allow color to dry on the Applicator! Replace original cap on Hair Color Cream to keep Cream
from drying out.
INSERTING AND REMOVING A STAMP PATTERN
1. Select the Stamp Pattern of your choice.
2. Place the Stamp Pattern into the Hair Stamper making sure the peg on the Stamp Pattern
fits into the opening inside the Hair Stamper. (Fig. 1)
3. Press down on the Pattern until it clicks into place. (Fig. 2)
4. To remove a Stamp, slightly squeeze the Stamper handles together with one hand and press
down on the Peg inside the Stamper with the other. Then release the handles. (Fig. 3)
PEG
OPENING
Fig. 1
Fig. 3
ADDING HAIR CREAM COLOR TO THE STAMPER
1. Carefully "dab" the color ONLY over the raised portion of the Stamp. (Fig. 4)
2. DO NOT allow color on the area around the Stamp. (If too much color is on the applicator,
remove excess color by dabbing applicator on a tissue or paper towel.)
IMPORTANT NOTES:When finished stamping, clean the stamps by wiping with a moist tissue
or paper towel. To clean Stamp crevices, use a cotton swab or discarded toothbrush.
2
Fig. 2
ADD COLOR
TO THIS AREA
ONLY.
Fig. 4
STAMPING ON COLOR
Patterened Stamps
Stamp
1. Choose the area of hair you wish to stamp.
in
this
2. Using the combination Comb and Brush, separate out a
area
portion of the hair approximately one inch wide and 1/8
inch thick. (Fig. 5)
3. Use the Hair Clip to keep the hair flat and taut.
4. With the Hair Stamper in the open position place the
hair across the bottom lip of the Hair Stamper. (Fig. 6)
5. Holding the hair taut, squeeze the handle of the Hair
Stamper then release.
Fig. 5
6. Gently open and remove the Hair Stamper from the
hair.
7. Allow the hair color to dry thoroughly before adding
additional color or before brushing or combing.
Streaker Stamp
The Streaker Stamp produces a wide streak of color.
SQUEEZE
1. Follow steps 1 - 4 above.
2. Squeeze the Stamper handle and hold it.
3. Pull the Stamper down the hair then release the Handle.
IMPORTANT NOTE: Stamp color onto the hair closest to
HOLD HAIR TAUT
the head. Color design stamped farther down the hair
ACROSS THIS AREA.
Fig. 6
shafts will not appear as clear and well defined.
ADDING HAIR CREAM COLOR TO THE HAIR
For a more narrow color streak do the following:
1. Follow the instructions for attaching the Hair
Cream Color Applicator to the Hair Cream Tube.
2. Gently squeeze the Hair Cream Color Tube until
color comes out of the Applicator sponge.
3. Choose the area of hair to which you wish to apply
Hair Cream.
4. Grasp the hair you wish to color with one hand and
move the Top of the Applicator down the hair,
painting on the color. (Fig. 7)
ADDING HAIR GLITTER GEL HIGHLIGHTS TO
THE HAIR
1. Unscrew the Hair Glitter Gel cap and slowly pull
out the wand.
2. Choose the area of hair you wish to highlight.
3. Grasp the hair with one hand and move the wand
down the hair to "paint" the color on your doll‛s
hair or your own hair. (Fig. 8)
NOTE: Color intensity may depend on child‛s hair
color. Hair Glitter Gel and Hair Color Cream works
best on lighter hair.
TO REMOVE COLOR
See "Removing the Hair Color Cream and Hair Glitter Gel" on Page 4.
Fig. 7
Fig. 8
3
Advertisement
