Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Honda Electronics Manuals
  4. Chain Hoists
  5. HONDEX HE-773-Di
  6. Operation manual

Honda Electronics HONDEX HE-773-Di Operation Manual

Electric hoist
Hide thumbs

Advertisement

Quick Links

Download this manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the HONDEX HE-773-Di and is the answer not in the manual?

Questions and answers

Summary of Contents for Honda Electronics HONDEX HE-773-Di

  • Page 2 INTRODUCTION Thank you very much for purchasing our product. ■Please be sure to read this operating manual carefully and understand the contents before the actual operation in order to keep your safety. ■Please store this manual safely at the convenient place so that you can read it when needed.

  • Page 3: Basic Specifications

    BASIC SPECIFICATIONS (12V and 24V spec) There exists 2 types of products: 12V and 24V. Please be sure which operating voltage is required before the installation. ELECTRIC HOIST DIMENSION Warning The main unit part of electric hoist is not waterproof. The hoist has the open area such as cable slot etc.

  • Page 4: Transducer Installation

    TRANSDUCER INSTALLATION ●Any works on the vessel are very unstable and risky. Installation/maintenance of transducer should be handled after landing the vessel on ground or fixing the vessel at shipyard etc. If not, it may cause serious injuries. これを守らないと死や身体に重大な損傷を招く恐れがあります。 ●Be sure to ventilate well inside the vessel when installing the transducer at the bottom of vessel.
  • Page 5 2. Hull Unit Please make sure to proper location of hull unit to be installed. The important points to be concerned are safety (intensity and water tightness) and easy maintenance. Add the extruding part of approx.5mm with FRP for the purpose of reducing the water pressure inside the trunk pipe while sailing.
  • Page 6 STORAGE/OPERATING METHOD FOR ELE.HOIST/SOUNDOME Please refer to the cautions below when installing the soundome to electric hoist or removing the soundome from trunk-pipe for the storage. 1. Oil filled inside the soundome Make sure that the transducer is always placed/stored straight-up. Placing side-way has the risk of leaking oil to the cable.
  • Page 7 INSTALLATION OF ELECTRIC HOIST Cut off the joint-pipe according to trunk-pipe length Lt. Pipe Length (Lt) = Waterline (fully loaded) + Min.50mm Trunk Pipe SPEC PVC Pipe PVC-U VP-75 Outside diameter ： ： ： ： ８９±０．５ ８９ ０．５mm ８９ ８９ ０．５...
  • Page 8 Pass the cable of soundome inside the joint-pipe. Apply the adhesive agent (for PVC pipe) onto the base of joint part (one round). Tighten the soudome and joint part. (clamping torgue: 8~10kgf.m) Fix the joint pipe and soundome with pipe guide (A).
  • Page 9 5. Use pipe guide (B) when trunk pipe length is 408mm or more. ※No need to use pipe guide (B) when the trunk pipe length is 408mm or less. 6. Check the bow mark of soundome and put the marking on the joint pipe with pen etc.
  • Page 10 Remove the clamping knobs and cover of electric hoist. Place the electric hoist on the trunk pipe. Choose the cable path and the direction for easier maintenance. (Consider the position of cover and clamping knob.) PCB side has the connection between power and Upper/Lower signal lines. The opposite side has the transducer cable.
  • Page 11 Recheck the location of electric hoist and put the marking of bow direction. If this arrow is the bow direction, Add Bow Marking...
  • Page 12 After fixing the location of electric hoist, put the marking with pen on the hoist and trunk pipe. Marking on Electric Hoist Marking on Trunk-Pipe. 8．According to the fixation location above, put the marking for screw hole on trunk pipe. 4 holes (Min.3 holes required at least.) Marking for screw hole...
  • Page 13 Insert O-ring. Insert the rubber bush into transducer part. Insert the cable of soundome.
  • Page 14 Set both markings for bow direction. Bow direction for Soundome Bow direction for Ele. Hoist Align the level of silver plate and joint pipe. Temporary fix with clamping screws. Fix the nut with screw wrench from the opposite side and tighten the screws Align both levels equal.
  • Page 15 Insert the joint pipe into trunk pipe carefully so that no scratch is on the soundome surface. Execute the temporary fixation. At this stage, no need to joint the hoist and trunk pipe since O-ring is ON. Again, recheck the bow direction is correct against the fixation position of hoist. Lastly, remove the parts from trunk pipe.
  • Page 16 Stroke Adjustment Initial set-up : 100mm Position of Lower Limit Switch Remove 2pcs screws shown above to lower the lower limit switch for longer stroke. 1cm step for each screw hole. The bottom hole means 5cm stroke spreading overall stroke to 150mm.
  • Page 17 Grease Cloth 4pcs grease clothes enclosed Remove 2 screws from the black plate for grease cloth fixation. Rotate the plate 90 degree, lift it to split into 2 pieces. Each plate part is identical.
  • Page 18 Rotate the cut area of each layer for 120 degree and insert 4 layers to the joint area. layer layer Upper Left Upper Right layer layer Bottom Bottom Lastly, tighten the plate with M6x20 screws and flat washers. Manage the flatness of plate by controlling left/right screws. 3mm is the initial reference gap in between.
  • Page 19 Add some water for smoothing O-ring and trunk pipe. Insert the joint pipe into trunk pipe carefully without causing any damage onto soundome. Keep pushing the joint pipe until the location of trunk pipe reaches the fixation position. Fix the trunk pipe and electric hoist with 4pcs 5x12 tapping screws. (Min 3pcs) Initial Set-up Refer to the operating manual for the initial set-up of main unit.
  • Page 20 Confirmation of Up/Down Movement Confirm the Up/Down movement. ① After setting the power breaker ON, the alarm goes ON followed by soundome moving upward. ② After reaching the upper limit position, the movement and alarm stop. (Check the soundome position stored inside correctly.) ③...
  • Page 21 Operating Precautions 1. Vessel needs to be stopped (3knots or less) for the operating the electric hoist (Up/Down movement). 2. Vessel speed needs to be 10knots or less when soundome is lowered. Soundome may be damaged or malfunctioned when exceeding the speed limit. Be sure to stop the vessel first and store the soundome back to trunk pipe before increase the vessel speed.
  • Page 22 Operating Method １． １． １． １． Lower Soundome ① Stop the vessel. (3 knots or less) ② Press MENU button of HE-773-Di. ③ Go to MENU1 and select “DOWN” for AUTO HOIST. Caution: This function is disabled when connecting to NMEA speed information and exceeding the speed limit.
  • Page 23 Case of Problem Alarm is ON when the following conditions occur. ① Fuse is blown caused by overcurrent. ② Soundome moving upward ③ Soundome moving downward Therefore, alarm turns OFF after soundome stops. Stop the vessel when confirming the condition of problem. Turn OFF the electric hoist before starting the operation.

  • Page 24: Standard Configuration

    STANDARD CONFIGURATION Pipe Guide-A Pipe Guide-B M5x20 SUS M5x20 SUS Screw ｘ8 Screw ｘ8 M5 SUS M5 SUS Spring Washer ｘ8 Spring Washer ｘ8 M5 SUS M5 SUS Nut ｘ8 Nut ｘ8 Joint Pipe Fixation Screw Rubber Bush 4×10 Screw x1 Electric Hoist System Joint Pipe with Socket PVC Pipe HI-VP VP25 1.5m...
  • Page 25 JULY2014 Edition ｔ ｈ ｔ ｈ ｔ ｈ ｔ ｈ...