Mitsubishi Electric MELSEC-Q Series User Manual page 12

3.5.28 Upper/lower setting limiter
(buffer memory address 55, 56, 87, 88: Un\G55, Un\G56, Un\G87, Un\G88).............................. 3-95
3.5.29 Program control run/reset (buffer memory address 57, 89: Un\G57, Un\G89) ............................. 3-95
3.5.30 Loop disconnection detection judgment time
(buffer memory address 59, 91: Un\G59, Un\G91) ........................................................................ 3-96
3.5.31 Loop disconnection detection dead band
(buffer memory address 60, 92: Un\G60, Un\G92) ........................................................................ 3-96
3.5.32 Unused channel setting (buffer memory address 61, 93: Un\G61, Un\G93) ................................ 3-97
3.5.33 PID constant read command from FeRAM
(buffer memory address 62, 94: Un\G62, Un\G94) ........................................................................ 3-97
3.5.34 Automatic backup setting after auto tuning of PID constants
(buffer memory address 63, 95: Un\G63, Un\G95) ........................................................................ 3-98
3.5.35 Alert dead band setting (buffer memory address 164: Un\G164) ................................................. 3-98
3.5.36 Alert delay count (buffer memory address 165: Un\G165) ............................................................ 3-98
3.5.37 Approach range setting (buffer memory address 167: Un\G167) ................................................. 3-99
3.5.38 Approach soak time setting (buffer memory address 168: Un\G168) ........................................... 3-99
3.5.39 PID continuation flag (buffer memory address 169: Un\G169) ..................................................... 3-99
3.5.40 Cascade ON/OFF (buffer memory address 176: Un\G176) .......................................................... 3-99
3.5.41 Cascade gain (buffer memory address 177: Un\G177) ............................................................... 3-100
3.5.42 Cascade bias (buffer memory address 178: Un\G178) ............................................................... 3-100
3.5.43 Cascade monitor (buffer memory address 179: Un\G179) ......................................................... 3-100
3.5.44 Alert 1 to 4 mode setting (buffer memory address 192 to 195, 208 to 211:
Un\G192 to Un\G195, Un\G208 to Un\G211) .............................................................................. 3-101
3.5.45 Scaling value (buffer memory address 196, 212: Un\G196, Un\G212) ...................................... 3-101
3.5.46 Scaling range upper/lower limit value
(buffer memory address 197, 198, 213, 214: Un\G197, Un\G198, Un\G213, Un\G214) ........... 3-102
3.5.47 Scaling width upper/lower limit value
(buffer memory address 199, 200, 215, 216: Un\G199, Un\G200, Un\G215, Un\G216) ........... 3-102
3.5.48 Hold command (buffer memory address 201, 217: Un\G201, Un\G217) ................................... 3-103
3.5.49 Command advancing (buffer memory address 202, 218: Un\G202, Un\G218) ......................... 3-104
3.5.50 SV tracking setting (buffer memory address 203, 219: Un\G203, Un\G219) ............................. 3-104
3.5.51 Forced output command (buffer memory address 204, 220: Un\G204, Un\G220) .................... 3-105
3.5.52 Forced output manipulated value (MV)
(buffer memory address 205, 221: Un\G205, Un\G221) ............................................................. 3-105
3.5.53 Segment monitor (buffer memory address 256, 512: Un\G256, Un\G512) ................................ 3-105
3.5.54 Segment remaining time (buffer memory address 257, 513: Un\G257, Un\G513) .................... 3-105
3.5.55 Execution times monitor (buffer memory address 258, 514: Un\G258, Un\G514) ..................... 3-106
3.5.56 Pattern end output flag (buffer memory address 259, 515: Un\G259, Un\G515) ....................... 3-106
3.5.57 End status flag (buffer memory address 260, 516: Un\G260, Un\G516) .................................... 3-106
3.5.58 Wait status flag (buffer memory address 261, 517: Un\G261, Un\G517) ................................... 3-106
3.5.59 Hold status flag (buffer memory address 262, 518: Un\G262, Un\G518) ................................... 3-106
3.5.60 Advancing completion flag (buffer memory address 263, 519: Un\G263, Un\G519) ................. 3-107
3.5.61 Execution pattern monitor (buffer memory address 264, 520: Un\G264, Un\G520) .................. 3-107
3.5.62 Zone PID monitor (buffer memory address 265, 521: Un\G265, Un\G521) ............................... 3-107
3.5.63 Forced output status flag (buffer memory address 266, 522: Un\G266, Un\G522) ................... 3-107
3.5.64 Execution pattern (buffer memory address 272, 528: Un\G272, Un\G528) ............................... 3-108
3.5.65 Start mode (buffer memory address 273, 529: Un\G273, Un\G529) .......................................... 3-108
3.5.66 Time scale (buffer memory address 274, 530: Un\G274, Un\G530) .......................................... 3-109
A - 10 A - 10