Makita DVC560 Instruction Manual page 12

ASSEMBLY
CAUTION:
Always be sure that the appli-
ance is switched off and the battery cartridge
is removed before carrying out any work on the
appliance.
CAUTION:
Always wear dust mask during
assembly or maintenance.
Handle connecting
1. Insert the handle pole fully to the cleaner body as
shown in the figure.
2. Close the lock latch.
► Fig.2: 1. Handle pole 2. Red marking 3. Lock latch
NOTICE:
Insert the handle fully until the red
marking cannot be seen.
Hose connecting
Insert the hose into the mounting port of the appliance
and turn the horse until it locks.
► Fig.3
Pipe connecting
Insert the tip of the aluminum pipe to the joint, and then
attach the aluminum pipe to the pipe holder.
► Fig.4: 1. Joint 2. Pipe holder
NOTICE:
Insert the aluminum pipe in correct
direction as shown in figure. Otherwise the pipe
holder will not be locked and the aluminum pipe may
come off.
► Fig.5
Installing or removing battery cartridge
CAUTION:
Always switch off the appliance
before installing or removing of the battery
cartridge.
CAUTION:
Hold the cleaner and the battery
cartridge firmly when installing or removing bat-
tery cartridge. Failure to hold the cleaner and the
battery cartridge firmly may cause them to slip off
your hands and result in damage to the cleaner and
battery cartridge and a personal injury.
CAUTION:
Be careful not to pinch your fin-
gers when opening or closing the battery cover.
Failure to do so may cause personal injury.
To install the battery cartridge, release the lock first, and then
open the battery cover. After that, insert the battery cartridge.
► Fig.6: 1. Lock 2. Battery cover
Align the tongue on the battery cartridge with the groove in
the housing and slip it into place. Insert it all the way until it
locks in place with a little click. Then lock the battery cover.
► Fig.7: 1. Battery cartridge 2. Button
To remove the battery cartridge, slide it from the appli-
ance while sliding the button in front of the cartridge.
CAUTION:
Always install the battery cartridge
fully. If not, it may accidentally fall out of the appli-
ance, causing injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: The cleaner does not work with only one
battery cartridge.
Installing the filter bag
CAUTION:
Do not use a damaged filter bag.
Always use the vacuum cleaner with the filter bag
properly installed. Otherwise the vacuumed dust
or particles may be exhausted from the cleaner
and they may cause respiratory disease to the
operator.
Install the filter bag before using cleaner.
Filter bag is a throw-away type. Throw away the entire
filter bag without emptying when it has become full.
NOTICE:
When the filter bag is already full or
clogged, replace with new one. Continuous use
with the filter bag full or clogged results in reduced
suction power.
NOTICE:
To prevent dust from getting into the
motor:
— Make sure that the filter bag is installed
before use.
— Do not use a broken or ripped bag.
Otherwise the motor may be broken.
NOTICE:
Do not fold the cardboard at its open-
ing when installing the filter bag.
NOTICE:
The filter bag for the cleaner is an
important component for maintaining the appli-
ance performance. Using non-genuine filter bag
may cause smoke or ignition.
NOTE: When the filter bag is not installed in the appli-
ance, the dust box cover does not close completely.
1. Unlock the lever and open the dust box cover.
► Fig.8: 1. Lever 2. Dust box cover
2. Insert the filter bag into the slot on the holder so
that the side with mark
3.
Hook the latch of the holder.
► Fig.9: 1. Slot 2. Filter bag 3. Holder 4. Latch
4. Make sure that only the marking on the cardboard
can be seen through the slit of the holder.
► Fig.10: 1. Marking 2. Slit
5. Lock the dust box cover certainly.
CAUTION:
Be careful not to pinch your fin-
gers when hooking the latch, and when closing
the dust box cover.
12 ENGLISH
enters first.