Specifications; Ec Declaration Of Conformity - Makita HM1111C Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Model
Blows per minute
Overall length
Net weight with D-shaped side handle
Net weight with side grip
Safety class
• Due to our continuing programme of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for chiselling work in concrete,
brick, stone and asphalt as well as for driving and com-
pacting with appropriate accessories.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745:
Model HM1111C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model HM1101C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
) : 88 dB (A)
pA
) : 99 dB (A)
WA
) : 90 dB (A)
pA
) : 101 dB (A)
WA
HM1111C
528 mm
8.0 kg
7.8 kg
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN60745:
Model HM1111C
Work mode : chiselling function with side handle
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : chiselling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model HM1101C
Work mode : chiselling function with side handle
Vibration emission (a
Uncertainty (K) : 2.0 m/s
Work mode : chiselling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
4 ENGLISH
HM1101C
-1
1,100 - 2,650 min
528 mm
7.3 kg
7.2 kg
II
2
) : 7.5 m/s
h,CHeq
2
2
) : 8.0 m/s
h,CHeq
2
) : 13.5 m/s
h,CHeq
2
) : 13.5 m/s
h,CHeq
2
2
2