Download Print this page

Safety Information; Initial Install - Honeywell Kaliza User Manual

Hide thumbs

Advertisement

SAFETY INFORMATION
f
CAUTION: This device complies with Industry Canada license-exempt
RSS standard(s). Operation Is ae,
De
ete
two
conditions:
(1) this device may not cause interference,
and (2) this device must accept any interference, including
ice that
may
cause undesired operation of the device (if applicable)
CAN ICES-005 (B) / NMB-005 (B)
—Reorient or relocate the receiving antenna
Increase the separation between
the equipment
and receiver
Connect the equipment into and outlet
on a circuit different from that to which the receiver is connected.
Consult the dealer o r an experienced radio/TV technician for help
Please
note
changes or modifications
not expressly
approved
by the party
responsible for compliance could void the user's authority to
perate
the
equipment
C l u b Parkway #225
8125
CARE AND MAINTENANC
At least twice each year, lower the canopy to check the downrod assembly and tighten all screws on the fan. Clean the motor
housing and blades with a soft brush or lint-free cloth to avoid scratching the finish
Paglia Shut off the main power supply before you begin any maintenance task. Do NOT use water or a damp cloth to clean
the
fan
PREPARATION
Before beginning the assembly of this product, ensure all parts are present. Compare all parts with the package contents list
and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated assembly time: 2 hours
Tools required (not included): Electrical tape, Phillips Screwdriver, Safety Glasses, Step Ladder, and Wire Strippers.
1. Turn off power to the fan at the breaker box and the wall switch (Figure 1.1). DANGER: Failure to disconnect the power supply
prior to installation may result in serious injury or death.
2. Choose one of the following mounting options (Figure 1.2):
Standard Mount - best suited for ceilings 8 feet or higher. For very high ceilings, use a longer downrod (not included).
Angle Mount - best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to ensure proper blade
clearance.
Ensure the ceiling angle is not steeper than 10 degrees.
Flushmount Installation - not available for this model
Closemount Installation - not available for this model
3. Choose a suitable location - Ensure the blades will be at least 30 inches from any obstructions. Also check
the downrod
length to ensure the blades will be at least 7 feet above the floor (Figure 1.3).
=|
jin. min >
)
iS
=
2
ae
ony |
=
Qy
GV
=
sid
Standard Mount
Angle Mount
I
\ots/
Flushmount
Clasemount
Figure 1.1
Figure 1.2
Figure 1.3
INITIAL INSTALL.
ie)
1. Loosen all four mounting bracket screws and completely remove the two screws from the round holes in the canopy. Then
remove mounting bracket from the canopy and save them for later. Remove the canopy from the mounting bracket (Figure 2.1)
2. Install the mounting bracket to the outlet box (sold separately) using the screws and washers provided with the outlet box
(Figure 2.2),
3. Remove the 12 Phillips-head motor screws from the top of the motor assembly and save for blade arm assembly (Figure 2.3).
i
©®
Installation»)
|
oa
Standard
|
|
Motor Screw
v
FF
—h
|
v
se
|
é
Canopy
Mounting
Bracket Screw
i
|
Angle Mount
*
=
ce
NX
een
npc
a
Figure 2.1
Figure 2.2
Figure 2.3

Advertisement

loading

  Related Manuals for Honeywell Kaliza

This manual is also suitable for:

51035510365147751626