Subscribe to Our Youtube Channel
Related Manuals for Magnetek SBP2
Summary of Contents for Magnetek SBP2
- Page 1 SBP2 ® Pendant Pushbutton Stations Installation Instructions Part Number: 005-1053 Rev 6 June 2020 © Copyright 2020 Magnetek SBP2 ® Pendant Pushbutton Stations Installation Instructions June 2020...
- Page 2 Page Intentionally Left Blank SBP2 Pendant Pushbutton Stations Installation Instructions June 2020 Page 2 of 26...
-
Page 3: Table Of Contents
1.3 Disassembling Enclosure ................9 1.4 Installing Pendant Control Cable .............9 Wiring and Marking Information ..............10 Considering the Environment................11 Operating the SBP2 Pendant Pushbutton Station Safely ......12 4.1 Conducting a Pre-Operation Inspection..........12 Typical Installation of the Strain-Relief Round Cable........13 Wiring and Repairing ..................15 Performing Maintenance................16... - Page 4 E-mail: mhcustomerservice@magnetek.com Fax Numbers: Main: 800-298-3503 Sales: 262-783-3510 Service: 262-783-3508 Magnetek, Inc. has additional satellite locations for Canada and the United States. For more information, please visit www.columbusmckinnon.com/magnetek. SBP2 Pendant Pushbutton Stations Installation Instructions June 2020 Page 4 of 26...
- Page 5 It is the responsibility of the owners, users and operators of the Magnetek Products to know, understand and follow all of these requirements. It is the responsibility of the employer to make its employees aware of all of the above listed requirements and to make certain that all operators are properly trained.
- Page 6 SBP2-B liability in connection with the sale or use of this product. Maintained On/Off 2-Button Switch SBP2-H2 For information on Magnetek’s product warranties by product type, please visit Maintained On/Off (N.O./N.C.) 2-Button Switch SBP2-H3 www.columbusmckinnon.com/magnetek. Button Cover Black for Single-, Two-, Three-Speed Switches WC2-LB Button Cover –...
- Page 7 SBP2 is a component. For applications other than overhead cranes or hoists, consult Electromotive Systems at 1-800-288-8178. Six-Button (4) Single-Speed with On/Off SBP2-6-WB Read the entire contents of this manual before you install or use the SBP2 Six-Button (4) Two-Speed with On/Off SBP2-6-WBS Pendant Pushbutton Station.
-
Page 8: Installing And Wiring The Sbp2 ® Pendant Pushbutton Station
1 Installing and Wiring the SBP2 Pendant Pushbutton 11 Assembly Drawing ® Station 1.1 Taking Precautions During Installation • Do not expose the unit to cold blasts of air that might cause condensation (for example, an air conditioning duct). •... -
Page 9: Taking Precautions During Wiring
Remove the back cover by loosening the enclosure screws. 1.4 Installing Pendant Control Cable NOTE: Magnetek recommends the use of a suitable outdoor-rated, oil-resistant pendant cable that is both UL listed and CSA recognized. When cutting or stripping wires, ensure that particles do not fall into the enclosure. -
Page 10: Wiring And Marking Information
0.500" – 0.625" 00-4981 0.562" – 0.687" 00-4982 0.625" – 0.750" 00-4983 0.687" – 0.812" 00-4984 SBP2 Pendant Pushbutton Stations Installation Instructions SBP2 Pendant Pushbutton Stations Installation Instructions June 2020 June 2020 Page 10 of 26 Page 19 of 26... -
Page 11: Considering The Environment
Do not expose the unit to cleaning solvents that will penetrate the unit’s and label. Replace damaged switch gaskets and labels to prevent enclosure. contamination of the switch contacts. Call Magnetek at 800-288-8178 for replacement gaskets and labels. SBP2 Pendant Pushbutton Stations Installation Instructions... -
Page 12: Operating The Sbp2 Pendant Pushbutton Station Safely
4 Operating the SBP2 Pendant Pushbutton Station 8 Practicing Safe Crane Operation Safely • When moving a load with the crane, stand facing the suspended load; move the load away from you. When using a pendant station, take the following precautions: •... -
Page 13: Typical Installation Of The Strain-Relief Round Cable
OFF position when released. • Inspect the condition of the pendant on a regular basis (dependent on duty cycle). SBP2 Pendant Pushbutton Stations Installation Instructions SBP2 Pendant Pushbutton Stations Installation Instructions June 2020 June 2020... -
Page 14: Wiring And Repairing
Replace the cable if it is cracked or split. • When cutting or stripping wires, ensure that particles do not fall into the enclosure. SBP2 Pendant Pushbutton Stations Installation Instructions SBP2 Pendant Pushbutton Stations Installation Instructions June 2020 June 2020...
Need help?
Do you have a question about the SBP2 and is the answer not in the manual?
Questions and answers