Table of Contents
Advertisement
INSTRUCTION MANUAL
INSTRUCTION MANUAL
DC Motor Belt Drive
TM
ATOMS /ATOMS+ ATR/ANR Series
GARAGE DOOR OPENER
IMPORTANT:
•
Please read this manual and enclosed safety materials carefully!
• Safety Infrared Sensor MUST BE INSTALLED and aligned properly.
• Periodic checks of the opener are required to ensure safe operation.
• Save this manual for future reference.
• This Equipment meets or exceeds all Federal, State and UL325 Safety Requirements.
• For more information, updates and useful links, please visit our website http://www.skylinkhome.com
DO NOT RETURN TO THE STORE
TM
ENGLISH
ENGLISH
P/N: 101Y428
P/N: 101Y549-001
TABLE OF CONTENT
TABLE OF CONTENT
INTRODUCTION............................................................................................................................... 3
PRE-INSTALLATION CHECKLIST ................................................................................................... 4
WHAT IS INCLUDED ........................................................................................................................ 5
IMPORTANT INSTRUCTIONS.......................................................................................................... 8
ASSEMBLE THE RAIL ...................................................................................................................... 9
INSTALL THE HEADER BRACKET .................................................................................................14
HANG THE OPENER....................................................................................................................... 17
INSTALL THE DOOR BRACKET..................................................................................................... 19
INSTALL THE DOOR ARMS ........................................................................................................... 21
CONNECT THE OPENER TO POWER .......................................................................................... 25
INSTALL SAFETY BEAM SENSOR................................................................................................ 27
.............................................................................................................
SAFETY TEST................................................................................................................................ . 45
OPERATIONS ............................................................................................................................... 46
MAINTENANCE .............................................................................................................................. 49
BACKUP BATTERY........................................................................................................................ 51
TROUBLE SHOOTING.................................................................................................................... 54
PROGRAMMING TO THE INTERNET HUB.................................................................................... 57
ACCESSORIES............................................................................................................................... 59
FCC ................................................................................................................................................. 61
LIMITED WARRANTY .................................................................................................................... 62
CUSTOMER SERVICE.................................................................................................................... 63
.............................................................
23
38
2
2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SkyLink ATOMS ATR Series
Summary of Contents for SkyLink ATOMS ATR Series
-
Page 1: Table Of Contents
INSTRUCTION MANUAL TABLE OF CONTENT TABLE OF CONTENT INSTRUCTION MANUAL INTRODUCTION..........................3 DC Motor Belt Drive PRE-INSTALLATION CHECKLIST ....................4 WHAT IS INCLUDED ........................5 IMPORTANT INSTRUCTIONS......................8 ATOMS /ATOMS+ ATR/ANR Series ASSEMBLE THE RAIL ........................9 INSTALL THE HEADER BRACKET ....................14 GARAGE DOOR OPENER HANG THE OPENER........................ -
Page 2: Introduction
INTRODUCTION PRE-INSTALLATION CHECKLIST Congratulations on your purchase of Skylink Garage Door Opener, a garage door opener with many innovative features. Features include extremely quiet operation with DC motor; automatic force adjustment so the door can be closed with just the right amount of force, not overpowered; state of the art safety reversal systems that protect your family and property near the door. -
Page 3: What Is Included
WHAT IS INCLUDED WHAT IS INCLUDED WHAT IS INCLUDED The garage door opener and all accessories are packaged in one carton. Hook Safety Labels Shielding Plate Keychain Remote* Keychain Remote* Backup Battery* Wall Console* Keyless Entry* Wireless Wall Console* Hanging Bracket Belt Assembly Straight Arm Safety Beam Kit*... -
Page 4: Important Instructions
IMPORTANT INSTRUCTIONS IMPORTANT INSTRUCTIONS WHAT IS INCLUDED BAG B Rail Assembly To reduce the risk of severe injury or death: 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. 2. Check with the door manufacturer to determine if additional reinforcement is required to B2 x 1 support the door prior to installation of the garage door opener. -
Page 5: Assemble The Rail
ASSEMBLE THE T-RAIL ASSEMBLE THE RAIL ASSEMBLE THE RAIL Please note the “ ” marking on the trolley which indicates this side to the door. 1. Connect the Rail Sections Align the 6 Rail sections on the floor. Connect the rails together by sliding the taped ends to the untapped ones. 2. - Page 6 ASSEMBLE THE RAIL ASSEMBLE THE RAIL B1 (x2) 5. Attach the Rail to the Opener 8. TIghten the Belt Raise the rail so the rail assembly can Connect the 2 ends of the turnbuckle assembly together. sit on the motor unit. Insert the sprocket Press and twist the two parts to secure together.
-
Page 7: Install The Header Bracket
INSTALL THE HEADER BRACKET INSTALL THE HEADER BRACKET ASSEMBLE THE RAIL Remove the “U” pin from the turnbuckle after tighten 1. Mark the Door Centerline the belt tension properly. Close the door from inside the garage and mark the vertical centreline of the door on the wall and the top door panel. - Page 8 INSTALL THE HEADER BRACKET INSTALL THE HEADER BRACKET 3. Attach a 2x4 (if necessary) 5. Position The Opener If the calculated header bracket is above the door header, attach a 2x4 between two studs to install Position the pulley bracket against the header bracket. the header bracket.
-
Page 9: Hang The Opener
HANG THE OPENER HANG THE OPENER HANG THE OPENER 1. Raise the Opener 2. Attach the Hanging Brackets Raise the opener onto a stepladder. Use extra spacers on top of the ladder if the ladder is not tall Hanging brackets should be angled to provide rigid support. Measure the distance from the motor enough. -
Page 10: Install The Door Bracket
INSTALL THE DOOR BRACKET INSTALL THE DOOR BRACKET INSTALL THE DOOR BRACKET One-Piece Wood Doors Bolt 5/16 x 2” (8 x 50 mm) (not included) Top of Door For wood doors, drill 5/16” (8 mm) holes through the door and secure bracket with 5/16 x 2”... -
Page 11: Install The Door Arms
INSTALL THE DOOR ARMS INSTALL THE DOOR ARMS INSTALL THE DOOR ARMS 1. Attach Emergency Release Rope 3. Connect the Door Arm to the Trolley Sectional Door One-piece Jamb Door Connect the straight door arm to the trolley with Connect the curved door arm to the trolley with clevis pin and hitch pin. -
Page 12: Install The Wall Console/Lcd Wall Console
INSTALL THE WALL BUTTON/CONSOLE FOR ATOMS INSTALL THE WALL CONSOLE/LCD WALL CONSOLE INSTALL THE WALL CONSOLE/LCD WALL CONSOLE 1. Location Install LCD Wall Console on ATOMS+ Place the wall console or LCD wall console at least 5’ (1.5 m) 3a. Secure the mounting bracket with two screws. above the finished floor or the topmost step. -
Page 13: Connect The Opener To Power
CONNECT THE OPENER TO POWER CONNECT THE OPENER TO POWER CONNECT THE OPENER TO POWER 1. Connect AC Power 3. Permanent Wiring/Remove the Power Cord Plug motor unit into grounded outlet. If a grounded outlet is not available, contact a qualified electrician to install a proper outlet. DO NOT ACTIVATE THE OPENER UNTIL INSTRUCTED. -
Page 14: Install Safety Beam Sensor
INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR 3. Mounting the Sensor on the Door Track Slide (1) and clip (2) the mounting bracket onto the garage door track. Ensure the sensor is mounted between 4” (10 cm) and 6” (15 cm) above the ground. - Page 15 INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR 7. Testing with Obstruction NOTE With the sensors properly aligned, place an Remove the spring bracket from the mounting bracket if installing to the wall or floor. obstacle in the path of the beam. Press the 1.
- Page 16 INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR 2. Mount the shielded Wireless Safety Beam sensor back to back on the door tracks. 5. Once the Wireless Safety Beam sensor is programmed, both the green LED on the Radio Module and the blue LED on the Wireless Safety Beam sensor will flash once.
- Page 17 INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR...
- Page 18 INSTALL SAFETY BEAM SENSOR INSTALL SAFETY BEAM SENSOR...
- Page 19 PROGRAMMING GUIDE – LCD WALL CONSOLE (ATOMS+ ONLY) INSTALL SAFETY BEAM SENSOR Program your garage door opener with following Option 1 or Option 2. Option 1: from the Wall Console While programming, the and buttons can be used to move the door as needed. 1.
- Page 20 (ATOMS+ ONLY) PROGRAMMING GUIDE – LCD WALL CONSOLE PROGRAMMING GUIDE – LCD WALL CONSOLE (ATOMS+ ONLY) 12. The LCD display will flash the number 18. The garage door opener will beep if “4”. remote is successfully programmed and the flashing remote icon will 13.
-
Page 21: Programming Guide
- ATOMS & ATOMS+ PROGRAMMING GUIDE PROGRAMMING GUIDE - ATOMS & ATOMS+ Option 2: from the Garage Door Opener While programming, the buttons can be used to move the door as needed. 12. The LED display will show the number A. - Page 22 - ATOMS & ATOMS+ PROGRAMMING GUIDE PROGRAMMING GUIDE - ATOMS & ATOMS+ D. Erasing all the Remote Controls from Opener C. Keypad Initial Setup Note: To erase any unwanted remote controls, first erase all remotes. The factory default PIN is 0 0 0 0. It will be used during the keypad initial setup. After you set your own PIN, you will need to use your current PIN instead of 0 0 0 0 in below steps.
-
Page 23: Safety Test
SAFETY TEST OPERATION... - Page 24 OPERATION OPERATION...
-
Page 25: Operations
OPERATION OPERATION SET-UP Auto closer * on ATOMS (Deluxe Wall SET-UP Auto closer * on ATOMS+ (LCD Wall Console) Console) The opener has the option to program how long the door should be closed after it has been opened. Press the large button on the wall console to activate the garage door opener. -
Page 26: Maintenance
MAINTENANCE MAINTENANCE Lithium battery CR-2032 included. (Positive side up) Batteries AA size (sold separately) -
Page 27: Backup Battery
BACKUP BATTERY NOTE • These steps must be performed in this exact order very carefully to prevent a short in the battery by accident. Connecting the battery backup unit to the garage door opener unit Connect the 2-wire harness to the garage door opener unit. ... - Page 29 belt...
-
Page 30: Programming To The Internet Hub
PROGRAMMING TO THE INTERNET HUB * - Not application for ANR series LEARN WIRELESS CONTROL Press the [Set] button for one second. The LED display will show the letter “P”. -
Page 31: Accessories
ACCESSORIES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. -
Page 32: Limited Warranty
LIMITED WARRANTY CUSTOMER SERVICE CUSTOMER SERVICE Skylink Group (the Company) warrants to the original purchaser that products delivered hereunder will be free of defects in material and workmanship for the period listed below from the date of purchase. Electronics & Mechanical: 1 Year...
Need help?
Do you have a question about the ATOMS ATR Series and is the answer not in the manual?
Questions and answers