Subscribe to Our Youtube Channel
Related Manuals for Baroness LH62
Summary of Contents for Baroness LH62
- Page 1 Multi Configuration Mower Unit Owner's Operating Manual Serial No. LH62：10468-・LH66：10120- "Required reading" Read this manual before using the machine. Original Instructions Ver.1.4...
- Page 2 LH62・LH66 Greeting Thank you for purchasing the Baroness product. This manual describes the proper handling, adjustment, and inspection of your product. We hope you will use the product safely, and take advantage of its best performance. For details on the handling, adjustment and inspection of the main vehicle, refer to the Owner's Operating Manual for the main vehicle.
- Page 3 The operator is responsible for operating the product properly and safely. Maintenance should only be performed by a certified specialist. If you have any questions concerning maintenance or genuine parts, please contact a Baroness dealer or Kyoeisha. When making inquiries about the product, please specify the product's model designation and serial number.
- Page 4 When replacing parts, be sure to use genuine Baroness parts or parts designated by Kyoeisha. Note that the Baroness product warranty may not apply to defects caused by the use of parts from other companies. Prior to use, carefully read the following manuals to thoroughly understand the contents for safe and correct operation.
-
Page 5: Table Of Contents
LH62・LH66 Contents Safety .............. Page 1-1 Safe Operating Practices .......Page 1-2 Disposal ............Page 2-1 Recycle and Waste Disposal ......Page 2-2 Product Overview .......... Page 3-1 Specifications ..........Page 3-2 Names of Each Section ......... Page 3-4 Regulation Decals ..........Page 3-5 Safety Signs and Instruction Signs .... - Page 6 LH62・LH66 Contents...
-
Page 7: Safety
LH62・LH66 Safety Safe Operating Practices ...... Page 1-2 Page 1-1... -
Page 8: Safe Operating Practices
Observe the following safety instructions to ensure safe operation. Safe Operating Practices Read Safe Operating Practices described in the Owner's Operating Manual of Baroness main vehicle equipped with this mower unit thoroughly. Page 1-2 Safe Operating Practices... -
Page 9: Disposal
LH62・LH66 Disposal Recycle and Waste Disposal ....Page 2-2 About Recycle ........Page 2-2 About Waste Disposal ......Page 2-2 Page 2-1... -
Page 10: Recycle And Waste Disposal
LH62・LH66 Disposal Recycle and Waste Disposal About Recycle Recycling battery etc. is recommended for environmental conservation and economical use of resources. It may be required by local laws. About Waste Disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations. -
Page 11: Product Overview
LH62・LH66 Product Overview Specifications ........Page 3-2 Specifications List ........Page 3-2 Features of The MC Mower Unit ....Page 3-4 Names of Each Section ......Page 3-4 Regulation Decals ........Page 3-5 Positions of Regulation Decals ....Page 3-5 Description of Regulation Decals ..Page 3-5 Safety Signs and Instruction Signs .. -
Page 12: Specifications
LH62・LH66 Product Overview Specifications Specifications List LH62 Model LH62 Type Base unit (incl. two weights) With groomer Total length 17.76 in 451 mm 17.76 in 451 mm Dimen Total width 30.35 in 771 mm 30.35 in 771 mm sions Total height 11.50 in... - Page 13 LH62・LH66 Product Overview LH66 Model LH66 Type Base unit (incl. two weights) With groomer Total length 17.76 in 451 mm 17.76 in 451 mm Dimen Total width 34.41 in 874 mm 34.37 in 873 mm sions Total height 11.50 in 292 mm 11.50 in...
-
Page 14: Names Of Each Section
LH62・LH66 Product Overview Features of The MC Mower Unit Names of Each Section Equipped with a 6.4-inch (163 mm) - diameter reel cutter (cutting cylinder). Blade engagement can be adjusted by changing the reel cutter (cutting cylinder) position without changing the position and... -
Page 15: Regulation Decals
Part numbers for decals that need to be replaced are listed in the parts catalog. quwxcl-136 Order them from a Baroness dealer or Positions of Regulation Decals_001 Kyoeisha. Serial number plate Positions of Safety Decals and Instruction... - Page 16 LH62・LH66 Product Overview Description of Safety Decals and Instruction Decals Caution to Mutilation Decal K4205001600 DECAL, CAUTION TO MUTILATION Warning May cut your hand or leg - Stop the cutter rotation and engine. Otherwise you may get injured. STOP STOP...
-
Page 17: Handling Instructions
LH62・LH66 Handling Instructions Handling Precautions ......Page 4-2 Inspections ..........Page 4-2 Reel Cutter (Cutting Cylinder) and Bed Knife (Bottom Blade) ...... Page 4-2 Cover ............. Page 4-2 Belt ............Page 4-2 Roller ............. Page 4-3 Groomer ..........Page 4-3 CR brush ..........Page 4-3 Scraper .......... -
Page 18: Handling Precautions
LH62・LH66 Handling Instructions Make sure that the welding between the Handling Precautions reel cutter (cutting cylinder) and the disc has not come off. Important Cover This manual contains descriptions for handling Inspection of Covers the mower unit. For details on handling the main vehicle, refer... -
Page 19: Roller
LH62・LH66 Handling Instructions Roller CR brush Inspection of Rollers Inspection of CR Brush Bearing wear due to frequent use or bearing Note: damage caused by water infiltration may Depending on the specifications, this function prevent the roller from rotating smoothly. -
Page 20: Scraper
LH62・LH66 Handling Instructions Scraper Inspection of Scraper Inspection of Front Scraper ￭ Note: Depending on the specifications, this function may not be available. The operating efficiency may be reduced due to frequent use, objects crushed during operation, or damage during transportation. -
Page 21: Tightening Torques
LH62・LH66 Handling Instructions Tightening Torques Important Refer to the Tightening Torque table. Note that the Baroness product warranty may not apply to defects caused by incorrect or overtorque tightening, etc. Standard Tightening Torques Bolts and Nuts Important A number of bolts are used in each part of this machine. - Page 22 LH62・LH66 Handling Instructions General bolt Strength classification 4.8 Nominal diameter tib3yb-001 kgf-cm lb-in 3 - 5 30.59 - 50.99 26.55 - 44.26 7 - 9 71.38 - 91.77 61.96 - 79.66 14 - 19 142.76 - 193.74 123.91 - 168.17 29 - 38 295.71 - 387.49...
-
Page 23: Principal Tightening Torques
LH62・LH66 Handling Instructions Principal Tightening Torques Tightening Torque by Model LH66/LH62 LS66/LS62 Tighten the following bolts and nuts at the torque specified in the table. For thread locking adhesive, apply a middle strength thread locker (ThreeBond 1322 or equivalent anaerobic sealant). -
Page 24: Adjustment Before Work
LH62・LH66 Handling Instructions With the cutter adjustment nut, adjust the Adjustment before Work engagement between the reel cutter (cutting cylinder) and the bed knife (bottom blade) so Adjustment of Blade Engagement that newspaper (two to three sheets) will be cut by the edge of both blades when the... -
Page 25: Adjustment Of Cutting Height
LH62・LH66 Handling Instructions Loosen the cutting height adjustment Adjustment of Cutting Height nuts, and then adjust the rear roller so that it comes into contact with the cutting Cutting Height Adjustment height gauge. Since the rear roller cannot be accurately... -
Page 26: Adjustment Of Cutter Adjustment Spring
LH62・LH66 Handling Instructions After making adjustments, firmly tighten the Adjustment of Cutter Adjustment Spring cutting height adjustment nuts. If the diameter of the reel cutter (cutting Bed Knife (Bottom Blade) Angle Table cylinder) becomes smaller, adjust the cutter Make adjustments according to the conditions adjustment spring. -
Page 27: Adjustment Of Groomer
LH62・LH66 Handling Instructions Loosen the nuts securing the right and left Adjustment of Groomer rod holders. Note: Depending on the specifications, this function may not be available. Important Adjust the groomer height so that it is the same level on the right and left sides. -
Page 28: Adjustment Of Groomer Spring
LH62・LH66 Handling Instructions Important Adjust the position so that the vertical blade can make contact with the small screw for groomer setup. LH66_SP0_131 Adjustment of Groomer Spring_001 Pipe with adjustment screw Groomer spring 45.0 mm (1.77 in) 2qrq2r-002 Adjustment of CR Brush... -
Page 29: Adjustment Of Scraper
LH62・LH66 Handling Instructions Adjustment of Scraper Bolt Adjustment of Front Scraper Brush Note: Rear roller Depending on the specifications, this function Adjustment of CR Brush (installed together with may not be available. Groomer) Important Note: Do not place the scraper in contact with the Depending on the specifications, this function front roller too tightly. -
Page 30: Operation Method
LH62・LH66 Handling Instructions Operation Method Scraper Front roller Positions of Operation Decals 2.0 - 3.0 mm (0.079 - 0.118 in) Adjustment of Rear Scraper (Wire Type) Note: Depending on the specifications, this function may not be available. Important Do not place the scraper in contact with the rear roller too tightly. -
Page 31: Storage
LH62・LH66 Handling Instructions Groomer Clutch Lever Note: Depending on the specifications, this function may not be available. Caution The lever should be operated while the engine is stopped, and adjusted to the position suitable for your work. Important Do not pull the groomer clutch lever upward. - Page 32 LH62・LH66 Handling Instructions Page 4-16 Storage...
-
Page 33: Maintenance
LH62・LH66 Maintenance Maintenance Precautions ..... Page 5-2 Maintenance Schedule ......Page 5-2 Adjusted Values ........Page 5-3 Greasing ..........Page 5-4 About Greasing ........Page 5-4 Greasing Points ........Page 5-4 Maintenance Work ......... Page 5-6 Cleaning of Mower Unit ......Page 5-6 Back Lapping ......... -
Page 34: Maintenance Precautions
Use tools appropriate for each maintenance operation. Important For the safe and best performance of your machine, use Baroness genuine parts for replacement and accessories. Please note that our product warranty may be void if you use non-genuine parts for replacement or accessories. -
Page 35: Adjusted Values
LH62・LH66 Maintenance Maintenance Item Remarks Clean mower unit ○ Backlap blades ○ Maintenance schedules differ Grease ○ ○ according to greasing points Clean inside of CR brush belt cover ... -
Page 36: Greasing
LH62・LH66 Maintenance Add grease to A every 10 hours and B every Greasing 50 hours. About Greasing Front roller shaft There is one point each on the left and right Since there may be adhesion or damage due of the front roller shaft. - Page 37 LH62・LH66 Maintenance Right reel housing Groomer case Note: Depending on the specifications, this function may not be available. There are five points on the groomer case. 8bq62b-290 Greasing Points_005 Rear roller shaft There is one point each on the left and right 8bq62b-293 of the rear roller shaft.
-
Page 38: Maintenance Work
Cleaning of Mower Unit Prepare newspaper cut into strip, abrasive with back lapping powder mixed with oil or Important gel compound (Baroness genuine abrasive), and a brush. While cleaning, do not allow water on the sealed parts of the reel shaft. (Avoid high- pressure water cleaning.) - Page 39 LH62・LH66 Maintenance Lower all mower units to the ground. Caution Move the reel reverse switch to the When handling the reel cutter or bed knife, "Reverse" side. wear gloves to protect your hands. Run the engine at low speed. Pay attention not to let the reel cutter catch Move the reel rotation switch to the your gloves, etc.
-
Page 40: Sharpening Of Reel Cutter (Cutting Cylinder)
For sharpening the reel cutter (cutting cylinder), contact your dealer or Baroness unless you have a grinding machine. Caution Both the reel cutter (cutting cylinder) and the bed knife (bottom blade) are edged tools. -
Page 41: Replacement Of Reel Cutter (Cutting Cylinder)
LH62・LH66 Maintenance Sharpening is necessary when the reel The criteria for replacing the reel cutter (cutting cutter (cutting cylinder) reaches a condition cylinder) are described below. described below. However, these criteria are only a reference and do not guarantee performance like that of When the sharpening width (length of a new reel cutter (cutting cylinder). -
Page 42: Replacement Of Bed Knife (Bottom Blade)
LH62・LH66 Maintenance Replacement of Bed Knife (Bottom Blade) Adjustment of Belt Tension Caution Warning Both the reel cutter (cutting cylinder) and the Be sure to stop the engine before adjusting bed knife (bottom blade) are edged tools. the belts. Handle them carefully, since they could cut your hands and feet. - Page 43 LH62・LH66 Maintenance CR Brush Drive Belt (Installation with only CR CR Brush Drive Belt (Installation with Groomer at Brush) the same time) Note: Note: Depending on the specifications, this function Depending on the specifications, this function may not be available.
- Page 44 LH62・LH66 Maintenance Page 5-12 Maintenance Work...
- Page 45 1-26, Miyuki-cho, Toyokawa-city, Tel : +81 - 533 - 84 - 1390 Head Office Fax : +81 - 533 - 84 - 1220 Aichi-pref, 442-8530 JAPAN LH66----UM--GBZ/20L-00-S.K...
Need help?
Do you have a question about the LH62 and is the answer not in the manual?
Questions and answers