Panasonic KX-TG6671B Service Manual page 55

12.2.4. Commands (Base Unit)
See the table below for frequently used commands.
Command name
rdeeprom
readid
writeid
hookoff
hookon
getchk
How to use of 1.rdeeprom
"getchk"
2.sendchar epw
3.sendchar RST
4.getchk
5.sendchar epw
wreeprom
bs_burst
tx_high
tx_low
12.2.5. Commands (Portable)
See the table below for frequently used commands.
Command name
rdeeprom
readid
writeid
getchk
How to use of 1.rdeeprom
"getchk"
2.sendchar epw
3.sendchar RST
4.getchk
5.sendchar epw
weeprom
hs_burst
tx_high
tx_low
Function
Read the data of EEPROM
Read ID (RFPI)
Write ID (RFPI)
Off-hook mode on Base
On-hook mode on Base
Read checksum
Read EEPROM
Write EEPROM
Reset baseset
Read checksum
Write EEPROM
Write the data of EEPROM
Base unit outputs RF power in burst
test mode on antenna 2
Keep TX power high
Keep TX power low
Function
Read the data of EEPROM
Read ID (RFPI)
Write ID (RFPI)
Read checksum
Read EEPROM
Write EEPROM
Reset baseset
Read checksum
Write EEPROM
Write the data of EEPROM
Portable outputs RF power in burst test
mode
Keep TX power high
Keep TX power low
55
KX-TG6671B/KX-TG6672B/KX-TGA660B
Example
Type "rdeeprom 00 00 FF", and the data from address
"00 00" to "FF" is read out.
Type "readid", and the registered ID is read out.
Type "writeid 00 18 E0 0E 98", and the ID "0018 E0 0E
98" is written.
Type "hookoff".
Type "hookon".
Type "getchk".
Type "RdEeprom 04 73 04", and the data from address
"03 F2" to "03 F5" is read out
*This command gets 4 byte "WW", "XX", "YY", "ZZ".
*Please NEVER forget these 4 byte data!
Type "sendchar epw 04 73 04 FF FF FF FF"
Type "sendchar RST"
Type "getchk".
Type "sendchar epw 04 73 04 WW XX YY ZZ"
*"WW", "XX", "YY", "ZZ" is 4 byte data that already read
from same address.
Type "wreeprom 01 23 45". "01 23" is address and "45"
is data to be written.
Type"bs_burst"
Type"tx_high"
Type"tx_low"
Example
Type "rdeeprom 00 00 FF", and the data from address
"00 00" to "FF" is read out.
Type "readid", and the registered ID is read out.
Type "writeid 00 18 E0 0E 98", and the ID "0018 E0 0E
98" is written.
Type "getchk"
Type "RdEeprom 03 7D 04", and the data from address
"03 7D" to "03 80" is read out
*NEVER forget the read 4 byte data!
Type "sendchar epw 03 7D 04 FF FF FF FF"
Type "sendchar RST"
Type "getchk".
Type "sendchar epw 03 7D 04 WW XX YY ZZ"
*"WW", "XX", "YY", "ZZ" is 4 byte data that already read
from same address.
Type "wreeprom 01 23 45". "01 23" is address and "45"
is data to be written.
Type "hs_burst"
Type "tx_high"
Type "tx_low"