Advertisement
Quick Links
SB Multi Heads Series Installation Manual
1. Check Tools
2. Check the circumstances before installing
3. Check and adjust levelness.
4. Assembly
(1) Install Y fixed Frame
(2) Install the table
(3) Assemble Spool Stand and OP Box
(4) Assemble the Frame
(5) Assemble the bar switch and connetc cable
(6) Assemble the Offset Switch clear the cable
5. Running the machine without needle
6. Check the levelness and assemble the Table Support
7. Check the needle position and correct it
8. Re-set the upper dead & needle point of needle bar
9. Check and correct the Rotary Hook
10.Test the machine operation and Running
11.Test the Sewing
Index
Page 1 Of 17
(주)SUNSTAR SWF CS Center
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for SWF SB Series
Summary of Contents for SWF SB Series
- Page 1 7. Check the needle position and correct it 8. Re-set the upper dead & needle point of needle bar 9. Check and correct the Rotary Hook 10.Test the machine operation and Running 11.Test the Sewing Page 1 Of 17 (주)SUNSTAR SWF CS Center...
- Page 2 Check the circumstances before installing (1) Safe arrival of the machine Weight of SB Series machine is 3.0t (Not include Option) . ※ When moving the machine , must use the a forklift truck at least 5Ton above (2) Check the voltage specifications...
- Page 3 (Based oh the center, left and right within three grid , left and right within 6/100 tolerances) 3) Check levelness of L/R, F/R As indicated by noted , As indicated by noted , Leveling level it with a Leveling level it with a water level L/R,F/R. water level L/R,F/R. Adjusting height with lifting Beam Body(right) Beam Body(left) tools Page 3 Of 17 (주)SUNSTAR SWF CS Center...
- Page 4 If the height of water is above the Body side, put up machines with lifting tools for leveling. If the height of water is below the Body side, place the base "A" to "B" for leveling. Page 4 Of 17 (주)SUNSTAR SWF CS Center...
- Page 5 Table Plate and Table Support respectively. Insert Table Supporting Connecting Bar to the Table Support which is fixed to Beam Body, and fix the Table Fixing Support Screw close by. Page 5 Of 17 (주)SUNSTAR SWF CS Center...
- Page 6 3) Connect Table Connecting Plate and Table Support with Bolt. Table Support 4) Check the height of Table connection and correct it. Set correctly for showing a plane figure of table connection.(table d-party washer 0.3,0.5,0.8,1.0 ) Page 6 Of 17 (주)SUNSTAR SWF CS Center...
- Page 7 5)After assembling F/R Table ,install Table Support end Cap and Fixed Frame Rubber. (3)How to Assemble the Spool Stand and OP BOX 1) How to Assemble Spool Stand Page 7 Of 17 (주)SUNSTAR SWF CS Center...
- Page 8 ※ If Spool Stand/Angle and Fixed Bolt are not connected correctly, vibration from Spool Stand and Angle seems like harder than real. 2)Attach OP BOX and connect Cable. #Not for less than Y-Storke 1200mm model (Because it is not seperated from Op.Box) Page 8 Of 17 (주)SUNSTAR SWF CS Center...
- Page 9 When connecting Frame E Fixing Bolt , pre-connect first, move Frame Up and Down and then connect it. After connecting Frame, connect X-Shaft Couling.(2 each) with 5mm,3mm T-wrench. ※ If Frame E and Coupling Screw are not connected exactly, out of step and cutting will be happened. Page 9 Of 17 (주)SUNSTAR SWF CS Center...
- Page 10 (6) Assemble offset Switch and wire the cables.(6each) Wire the Signal Lines with Clamp. 1) Attach the Offset Switch Box specified location and connect Cables. 2) Fix the Cable to Table with Clamp. Page 10 Of 17 (주)SUNSTAR SWF CS Center...
- Page 11 Adjusting the height with lifting Beam Body side(right) Beam Body tools id (l f ) Level it less than 0.5mm error When leveling(F/R), within tolerances scope for equaling the height of 0 mark and Body side Install it bottom of the Leveling Base and Body When leveling the water, Hex.Bolt will get a lot of within 10MM,if the difference is big, loads, so, put up the Beam Body with lifting tools for Add the iron plate for adjusting. adjusting the height and then put down the (Attach the picture of this in the report Page 11 Of 17 (주)SUNSTAR SWF CS Center...
- Page 12 3.When instal the Table Supporter, be cautious of declension and when it's upper part contact to set up potion, turn it less than 270˚ and fix it. 4.Connect Table Supporter Nut. (23mm,nut, 2 each) Surface Table Supporter urn it less than 270˚ Page 12 Of 17 (주)SUNSTAR SWF CS Center...
- Page 13 If the needle is on ④, insert Guage to between Head Rail and Head If the needle is on the ③ ,replace it with thin for adjusting.(with 0.1T,0.2T,0.3T) Head Rail for adjusting. Page 13 Of 17 (주)SUNSTAR SWF CS Center...
- Page 14 Rotary Hook is needed. (2) Check/adjust the position of Rotary Hook. Adjust bulge part for being on Middle of the Needle, interval 0.5~0.7mm with Rotary Hook is needed ,by loosening Fixed Screw. Page 14 Of 17 (주)SUNSTAR SWF CS Center...
- Page 15 ※ Test with thread and fabrick from your company and check Status of machine ※ Test design your esteemed company. Write productivity report.Attach the Sample and Design. ※When Sewing TEST,train the worker and manager that how to operate/maintain the machine. Page 15 Of 17 (주)SUNSTAR SWF CS Center...
- Page 16 Check list for movement TEST and Running TEST After safe arrival,test movement of machine (1) JUMP TEST good (2) WIPER TEST good (3) PICKER TEST good (4) TRIM TEST good (5) THREAD SENSING TEST good Page 16 Of 17 (주)SUNSTAR SWF C/S Center...
- Page 17 ※ When test Sewing, check the cutting thread, work timek,missing the first needle and then report Attach the Sample and Design to report. ※When Sewing TEST,train the worker and manager that how to operate/maintain the machine. Page 17 Of 17 (주)SUNSTAR SWF C/S Center...
Need help?
Do you have a question about the SB Series and is the answer not in the manual?
Questions and answers