Table of Contents
Advertisement
Quick Links
http://waterheatertimer.org/Tork-Digital-timers-and-manuals.html#DGS
READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT
FEATURES
Single channel signal timer with 2 duration settings
288 signals in 5 minute increments
24 Hour scheduling with day omitting
Battery back-up uses standard 9 volt non-recharge-
able (not supplied). Lithium averages 450 hours of
power outage; Alkaline averages 175 hours
Manual activation or deactivation of signal
Automatic daylight saving - user selectable
Automatic leap year compensation
AM/PM or 24 hour format - user selectable
INSTALLATION
UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN
1. To remove unit from enclosure: Push tab on right
to swing unit to the left and remove.
2. Mount the enclosure at eye level using screws or
other suitable fastening device. Bring supply and
load wires in through bottom or side knockouts.
DO NOT USE TOP.
Input wires to controller must be dedicated i.e. no
other loads connected to the same circuit.
3. Install a standard 9 volt lithium or alkaline battery
(not supplied) by gently squeezing the right side of
the battery cover on the front of the unit and pull
to open. Pull out the battery connector and con-
nect the battery. Reinstall battery cover. Lithium
should be replaced every 3-5 years, Alkaline
every year.
TORK DGS180
DIGITAL SIGNAL TIMER
24 HOUR WITH DAY OMIT
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tork DGS180
Summary of Contents for Tork DGS180
- Page 1 TORK DGS180 DIGITAL SIGNAL TIMER 24 HOUR WITH DAY OMIT READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT FEATURES Single channel signal timer with 2 duration settings 288 signals in 5 minute increments 24 Hour scheduling with day omitting Battery back-up uses standard 9 volt non-recharge- able (not supplied).
- Page 2 NOTE: Unit can be fully programmed using battery power only. 4. Reinstall unit by reversing step #1 above and con- nect wires to unit as per suggested wiring dia- grams. See illustration on enclosure label. KEY FUNCTIONS HOUR OVER- MONTH DATE YEAR RIDE...
- Page 3 SETTING THE UNIT SELECT AM/PM OR 24 HOUR MILITARY FORMAT Upon powering up the unit, model number 180S appears on the screen. The LCD will next display 12H which is an automatic (AM/PM) format. Press ENTER to keep AM/PM format or press HOUR key to alter 24 hour (Military) format and then press ENTER.
- Page 4 TO SET CLOCK Press MODE key; display shows CLK. Press DAY/MONTH key to select today’s day. Press HOUR key to set present hour (check AM/PM). Press MIN key to set present minutes. Press ENTER key. Unit now stores present time. Seconds are set at zero.
- Page 5 Press mode key until display shows DATE. DATE Press MONTH key to select month. Press DATE key to set today’s date. Press YEAR key to set present year. Press ENTER key. Unit now stores present date. Note: If unit has correct entry for the calendar, then the unit will go into the SET mode.
- Page 6 3. Press SlG/SEC key to set signal 1 or signal 2. (Actual duration of signals will be set later.) 4. Press ENTER key to store the signal event. REPEAT ABOVE STEPS FOR ALL DESIRED SIG- NAL EVENTS Note: After each event is entered, the clock (in the set mode only) automatically advances 5 minutes.
- Page 7 1, then it will sound for 1 second. If either signal 1 or signal 2 are in progress when OVERRIDE key is pressed, then the signal will be ® TORK MLI-91(A) terminated. 1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542...
Need help?
Do you have a question about the DGS180 and is the answer not in the manual?
Questions and answers