Download Print this page

Connecting Cables To Terminals; Installation - Kenwood KTC-9090DAB Instruction Manual

Dab hideaway tuner
Hide thumbs

Advertisement

Connecting Cables to Terminals

2CAUTION
DC voltage is output from the DAB
antenna terminal of the DAB
hideaway tuner to supply power to
the DAB antenna. Be sure to connect
the supplied DAB antenna only.
Otherwise, the unit may be
damaged.
Control unit
DAB connection
cable
(Accessory1)
DAB hideaway
tuner
DAB
HIDEAWAY
TUNER
K T C – 9 0 9 0 D A B
24bit
D.R.I.V.E.
TO
RDI
TO
TO
CHANGER
OUTPUT
DAB
ANTENNA
HEAD
UNIT
To control unit
DAB antenna cable
(Accessory@)
Connection cable
RDI output
(supplied with the
Disc changer)
Disc changer
KENWOOD disc changer control input
To connect the Disc changer, consult your Disc
changer manual.
■ If you want to connect KCA-S210A
Control unit
]"N"
DAB hideaway tuner
O
N
OFF ON
PROTOCOL
AUX
AUX
SWITCH
SWITCH
IN
TO
TO
TO
H/U
CHANGER 1
CHANGER 2
KCA-S210A
26
(*...commercially available)
To KENWOOD disc changer / DAB control input
FM/AM antenna input
P.CONT.
ANT.CONT.
Power control/Motor
FM/AM antenna cable*
antenna control wire
(Blue/White)
FM/AM antenna
control cable*
1
(M10)
2
3
DAB/FM/AM
antenna
(Accessory7)
NOTE
• To use the data output from the Radio Data
Interface (RDI) connector, a separate RDI-enabled
component is required.
• The Radio Data Interface (RDI) output may contain
test data, but this isn't broadcast data.
NOTE
Connect the KTC9090DAB to the
terminal labelled TO CHANGER 2.
TO
TO
HEAD UNIT
CHANGER
NOTE
Set the PROTOCOL selection
switch to "N" position.
Disc changer

Installation

■ Mounting the DAB Antenna to the Roof
2CAUTION
• Make a hole in the roof and mount the
DAB antenna. Specialized knowledge is
required for this job and an installer should
be requested for the installation work.
• The DAB antenna should be mounted so
that it does not protrude beyond the width
and length of the car.
• Do not install at a spot where the roof is
markedly curved. Doing so will allow
water to enter from a gap between the
roof and the waterproof rubber.
• Securely fasten the screws that fix the
DAB antenna as well as the screws of the
DAB antenna itself. Screws that loosen
introduce the danger of the antenna
coming apart during travel.
1
Determine the mounting position of the
DAB antenna. (It replaces with
established FM / AM antenna.)
2
Wipe away any dirt from the mounting
position.
3
Remove the lining in a place where you
can make a hole in the roof.
Make a Ø19.5mm round hole, or a
14.8mm rectangular hole in the roof.
4
Mount the DAB antenna and fasten it
by tightening the nut from the inside.
5
Use a cable clamp to fix the antenna
cable and perform the wiring as far as
the DAB hideaway unit.
100 mm - 200 mm
• In the case of a round fixing hole
DAB antenna
(Accessory7)
(Accessory8)
Waterproof
rubber
(Accessory9)
Car roof
Ø19.5 mm
Nut
(Accessory!)
• In the case of a rectangular fixing
hole
DAB antenna
(Accessory7)
(Accessory8)
Waterproof
rubber
(Accessory0)
Car roof
14.8 mm
Nut
(Accessory!)
27

Advertisement

loading

  Also See for Kenwood KTC-9090DAB

  Related Manuals for Kenwood KTC-9090DAB