Pioneer ND-BT1 Owner's Manual page 4

CRD4118A_BT_owners.QX3e
About this unit
This unit is used to connect a Bluetooth enabled
cellular phone to a Pioneer HDD Navigation
System.
About Bluetooth
Bluetooth is a short-range wireless radio connectivity
technology that is developed as a cable replacement for
cellular phones, handheld PCs and other devices.
Bluetooth operates in 2.4 GHz frequency range and
transmits voice and data at speeds up to 1 megabit per
second. Bluetooth was launched by a special interest
group (SIG) that comprises of Ericsson Inc., Intel Corp.,
Nokia Corp., Toshiba and IBM in 1998, and it is currently
developed by nearly 2 000 companies worldwide.
• The Bluetooth word mark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by
Pioneer Corporation is under license. Other trade-
marks and trade names are those of their respective
owners.
Operating environment
This unit should be used within the temperature ranges
shown below.
Operating temperature range
EN300328 ETC test temperature : -20 and +55 °C
• The line-of-sight distance between this unit and your
cellular phone must be 10 meters or less in sending
and receiving voice and data via Bluetooth technol-
ogy. However, the transmission distance may become
shorter than the estimated distance, depending on
the environment in use.
• There are some Bluetooth enabled cellular phones
that can be incompatible with this unit due to their
Bluetooth version.
• The performance test of this unit with all Bluetooth
enabled cellular phones is not conducted. Also, it is
not guaranteed that this unit can be connected to all
Bluetooth enabled cellular phones.
• About the Bluetooth profile and its overview
It is required that the Bluetooth enabled cellular
phone to be connected to this unit is implemented
with the same profile.
HFP (Hands Free Profile): the profile used for hands-
free calling
OPP (Object Push Profile): the profile used for trans-
ferring data such as address books
2/14/06 2:00 PM Page 4
: -10 to +60 °C
(14 to 140 °F)
(-4 and 131 °F)
Installation notes
Velcro tape (hard) × 2
backside
Velcro tape (soft) × 2
• This unit may be installed in relatively unnoticeable
positions such as the passenger seat floor, however,
before fixing the unit, check the reception condition
of the Bluetooth unit with the setup-status monitor of
navigation system.
• Referring to Operation Manual included in navigation
system, check the connection and fine-tune the
reception of this unit.
• Thoroughly wipe off the surface before affixing the
velcro tape.
• Do not install the unit where it may (i) obstruct the
driver's vision, (ii) impair the performance of any of
the vehicle's operating systems or safety features,
including air bags, hazard lamp buttons or (iii) impair
the driver's ability to safely operate the vehicle.
• When disconnecting a connector, pull the connector
itself. Do not pull the lead, as you may pull it out of the
connector.
• Do not install the unit in places where it may become
subject to high temperatures or humidity, such as:
* Places close to a heater outlet.
* Places exposed to direct sunlight, such as on top of
the dashboard or the rear shelf.
• Places that may be splashed by rain, for example
close to the door.
• Use supplied velcro tapes to secure the unit so that it
doesn't move. It is extremely dangerous if cords are
exposed on the floor as they may become entangled
with the brake pedal etc. Hide cords so that they do
not get in the way when you are driving.
• Do not disassemble or modify this unit. To do so may
cause a fault.
Specifications
General
Max. Current Consumption ......0.25 A
Dimensions (W x H x D) ............89 mm x 16 mm x 48 mm
Weight........................................0.16 kg (0.33 lbs)
Bluetooth
Version ......................................Bluetooth 1.1 certined
Maximum Output Power ..........+4 dBm (Power Class 2)
(3-1/2 x 5/8 x 1-7/8 in.)
4