Related Manuals for MARS COMMERCE SOLO–KP
Summary of Contents for MARS COMMERCE SOLO–KP
- Page 1 SOLO–KP SOLO–KP LCD COMPACT MULTI-APARTMENT GSM DOOR ENTRY UNIT INSTALLATION MANUAL Version: SOLO-KP SOLO-KP LCD EXT-Installation-Manual_V5_0 18012017.doc Valid from SW release “SOLO_KP_EF_B_ON_PCK_20161022_v_3_3_1”.
-
Page 2: Table Of Contents
SOLO-KP (LCD) INSTALLATION MANUAL Contents FOR YOUR SAFETY ............................. 5 INTRODUCTION ..............................6 FEATURES AND APPLICATIONS ........................7 START UP ................................8 LED DISPLAY ................................ 9 CLEAR ALL PROGRAMMED DATA FROM SOLO-KP ................10 CONNECTING DIAGRAM ..........................11 PROGRAMMING SOLO-KP ..........................12 THE SOLO-KP PARAMETERS......................... - Page 3 SOLO-KP (LCD) INSTALLATION MANUAL 10.18 RECEIVE PIN ACCESS CODES (PPIN) ......................... 37 10.19 RECEIVE SPIN ACCESS CODES PARAMETERS (PSPIN) ..................38 10.20 STATE OF THE CREDIT FOR THE PREPAID CARD ....................38 10.21 STATE OF THE OUTPUTS (PORC) ..........................38 10.22 MANUAL GSM MODULE RETARD (MRES)........................
- Page 4 SOLO-KP (LCD) INSTALLATION MANUAL Figures Figure 1: SOLO-KP Connection diagram ..................11 Figure 2: Input Connection diagram....................13 Figure 3: Output Connection diagram ....................17 Tables Table 1: IN, ID and DD parameters ....................14 Table 2: IN, ID, DD parameters example ..................14 Table 3: Remote alarm reporting parameters ..................
-
Page 5: For Your Safety
SOLO-KP (LCD) INSTALLATION MANUAL FOR YOUR SAFETY Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information. SWITCH ON SAFELY Do not switch the unit on when use of wireless phone is prohibited or when it may cause interference or danger. -
Page 6: Introduction
SOLO-KP (LCD) INSTALLATION MANUAL INTRODUCTION SOLO-KP is a simple GSM intercom communication system for multi apartments, that is designed to ensure low-cost, reliable and single box solution for intercom application. It is designed for unlimited range, wire free GSM intercom and CLIP support. In addition SOLO-KP supports alarm detection, stay-alive messages, credit detection etc…... -
Page 7: Features And Applications
SOLO-KP (LCD) INSTALLATION MANUAL FEATURES AND APPLICATIONS Features: Built-in 4 band (2G) or 5 band (3G) GSM module Keypad call support (up-to 200 apartments) Keypad Access entry support (by 4 digit PIN codes – up to 2000 codes are possible) ... -
Page 8: Start Up
SOLO-KP (LCD) INSTALLATION MANUAL START UP VERY USE A MICRO SIM CARD (micro-SIM, see the picture) IMPORTANT WITH MEMORY FOR UP TO 250 CONTACTS! Insert SIM card to be used for SOLO-KP in your personal mobile phone. ERASE THE PIN CODE! IMPORTANT ... -
Page 9: Led Display
SOLO-KP (LCD) INSTALLATION MANUAL LED DISPLAY BLUE LED (LED1) Indicates the level of the GSM signal from 1 to 5 LED flashes (1 is weak signal, 5 is excellent signal) RED LED (LED2) When LED 2 is ON the unit has a problem with a GSM network connection or the GSM part of the unit is out of order. -
Page 10: Clear All Programmed Data From Solo-Kp
SOLO-KP (LCD) INSTALLATION MANUAL CLEAR ALL PROGRAMMED DATA FROM SOLO-KP This is highly recommended when a SIM card you are going to use for the SOLO-KP is not new and it already has some data stored in the phone book memory. By sending this SMS to SOLO-KP all programmed parameters and numbers are cleared: ;SDCLR;... -
Page 11: Connecting Diagram
SOLO-KP (LCD) INSTALLATION MANUAL CONNECTING DIAGRAM Before connection the SOLO-KP please take a look at connection diagram. Figure 1: SOLO-KP Connection diagram *Do not use the Power out (12V AUX) for electric lock driving! You can use it to power external sensors: Short-term current load (up to 1 minute) - up to 500mA;... -
Page 12: Programming Solo-Kp
SOLO-KP (LCD) INSTALLATION MANUAL PROGRAMMING SOLO-KP SOLO-KP device supports different types of programming: You can program SOLO-KP remotely by sending text commands (SMS commands). You can program SOLO-KP with Web server application. You can program SOLO-KP with direct USB connection, with the use of configuration software running on PC. -
Page 13: The Solo-Kp Parameters
SOLO-KP (LCD) INSTALLATION MANUAL THE SOLO-KP PARAMETERS To support versatile functionality of SOLO-KP different parameters are used. The parameters are divided in logical sections and are described in the following chapters. 9.1 ALARM SUPPORT Alarm reporting is supported by group of different parameters. First section is used to define the relations needed for alarm to be trigged. -
Page 14: Table 1: In, Id And Dd Parameters
SOLO-KP (LCD) INSTALLATION MANUAL 9.1.1.2 ID parameter ID parameter determines time period of the pulse length to trigger the alarm. The pulse time can be from 0,5 seconds to 9999 seconds. The default time is 0,5 seconds when the parameter value is 0. 9.1.1.3 DD parameter This parameter is used to define the delay between the time that alarm input is trigged and the time that alarm is reported. -
Page 15: Table 3: Remote Alarm Reporting Parameters
SOLO-KP (LCD) INSTALLATION MANUAL SOLO-KP device send SMS messages for reporting alarm events. NOTE 9.1.2.1 TN parameter Telephone numbers for remote alarm reporting are listed as TN parameters. Remote alarm reporting on SOLO-KP is done via SMS messages. 9.1.2.2 LN parameter This parameter is used to link alarm event from inputs or any other source to the telephone numbers from TN list. -
Page 16: Table 4: Remote Alarm Reporting Example
SOLO-KP (LCD) INSTALLATION MANUAL Direct programming on the SIM card SOLO-KP PROGRAMMING TABLE Name Number Description 042376678 1st telephone number Input 1 reports alarm to TN1 & TN3 1234 Input 2 reports alarm to TN1 & TN2 & TN3 & TN4 NAC event sent to TN1 Voice connection stay valid for max of 60s, after this time Voice connection breaks... -
Page 17: Output Management
SOLO-KP (LCD) INSTALLATION MANUAL 9.2 OUTPUT MANAGEMENT SOLO-KP supports the possibility to report alarms from inputs and any other events locally via 4 outputs. The behavior is defined using next parameters 9.2.1 OS parameter SOLO-KP device has 2 dedicated relay supported outputs. Outputs can be configured to different behavior: ... -
Page 18: Table 6: Output Management Parameters
SOLO-KP (LCD) INSTALLATION MANUAL 9.2.4 Table of parameters Name Comment Mode of operation for output 1 Mode of operation for output 2 Input 1 direct link to outputs Input 2 direct link to outputs NAC direct link to outputs Invert control for output 1 Invert control for output 2 Table 6: Output management parameters Example:... -
Page 19: Security Level - Sl
SOLO-KP (LCD) INSTALLATION MANUAL 9.3 SECURITY LEVEL - SL SL parameter from 0 to 5 defines which telephone number stored in the phone book from TN1 – TN5 can enter into programming and remote control of the SOLO-KP (dialing the SOLO-KP phone number or sending the SMS). -
Page 20: Prepaid Card Credit And Validity Information
SOLO-KP (LCD) INSTALLATION MANUAL 9.4 PREPAID CARD CREDIT AND VALIDITY INFORMATION SOLO-KP can be used with prepaid SIM cards and its limitations. To be able to overcome this limitation of the prepaid SIM cards, SOLO-KP offers the possibility of automatic checking mechanism for credit and time expiration. -
Page 21: Table 10: Prepaid Card Validity Parameters
SOLO-KP (LCD) INSTALLATION MANUAL 9.4.1.3 CREF, CTIM, CVODA parameters Parameters are used to find the credit value of the prepaid SIM card. Strings under these parameters are used to pars the replay message from the GSM provider. CREF - Pars string for the replays received from CC1 number ... -
Page 22: Set-Up Parameters
SOLO-KP (LCD) INSTALLATION MANUAL 9.5 SET-UP PARAMETERS Different parameters are used to support versatile functionality of SOLO-KP. 9.5.1 HTN parameter Hidden telephone number is a parameter used in order to conceal the telephone number of the SOLO-KP device. The default value is set to “1” which means that the number is displayed. 9.5.2 UDC parameter Parameter is used to synchronise SOLO-KP clock to GSM network clock. - Page 23 SOLO-KP (LCD) INSTALLATION MANUAL 9.5.6 MIC parameter MIC parameter enables you to change the sound level on microphone input. 9.5.7 SPK parameter SPK parameter enables you to change the speaker sound level. 9.5.8 ARST parameter ARST parameter defines periodic of auto restart time (in hours) of the SOLO-KP device. 9.5.9 MUT parameter MUT parameter enables you mutate the speaker sound while initiating voice connection.
-
Page 24: Table 12: Set-Up Parameters
SOLO-KP (LCD) INSTALLATION MANUAL 9.5.13 Table of parameters Name Comment Tel. number of SOLO-KP device Auto answer ring number Hidden telephone number SMS test time out Manual GSM provider selection Microphone volume control Speaker volume control ARST Time out control for automatic system restart Auto dial functionality ( Call TN1 ) Language selection Buzzer control... -
Page 25: Sms Messages Editor
SOLO-KP (LCD) INSTALLATION MANUAL 9.6 SMS MESSAGES EDITOR You can write and send a short SMS message for each alarm input. The default message is English, but it is possible to change language with LNG parameter. Each message is built from 3 parts and user can write the first (User Location) and the second (alarm event) part of the message. -
Page 26: Intercom
SOLO-KP (LCD) INSTALLATION MANUAL 9.7 INTERCOM Intercom functionality is supported by a set of parameters, used to tweak the functionality to each user needs. For each keypad entry SOLO-KP incorporates a group of parameters. SOLO-KP support up to 200 call groups. 9.7.1 KPAx and KPB1 parameters Parameters are the call numbers for intercom application. -
Page 27: Trade Button (Option)
SOLO-KP (LCD) INSTALLATION MANUAL Example: Direct programming on the SIM card SOLO-KP PROGRAMMING TABLE Name Number Description KPA1 040713470 Call group 1, Telephone number 1. KPB1 +38643364850 Call group 1, Telephone number 2. KPT1 Call group 1, time out control for voice connection. KPO1 Call group 1, output 1 Table 17: Intercom parameters example. -
Page 28: Direct Access By Entering Pin Code
SOLO-KP (LCD) INSTALLATION MANUAL 9.8.3 TBZE Parameter is used to define the end point of the active time interval. 9.8.4 Table of parameters Name Comment Trade button enable/define input. TBZS Trade button interval start. TBZE Trade button interval end. Table 18: Trade button parameters. Example: ... -
Page 29: Direct Access By Entering Temporary Access Codes - Spin - Via Illuminated Keypad
SOLO-KP (LCD) INSTALLATION MANUAL 9.9.2 Table of parameters Name Comment PIN1 Access entry code 1. PIN2 Access entry code 2. PIN3 Access entry code 3. PIN1998 Access entry code 1998. PIN1999 Access entry code 1999. PIN2000 Access entry code 2000. Table 20: Entering PIN code parameters. -
Page 30: Table 22: Entering Spin Access Code Parameters
SOLO-KP (LCD) INSTALLATION MANUAL 9.10.2 Table of parameters Name Comment SPIN1 SPIN access code 1. SPIN2 SPIN access code 2. … SPIN100 SPIN access code 100. Table 22: Entering SPIN access code parameters Example: Direct programming on the SIM card PROGRAMMING TABLE Name Number... -
Page 31: Caller Id Recognition (Clip), Caller-In Function
SOLO-KP (LCD) INSTALLATION MANUAL 9.11 CALLER ID RECOGNITION (CLIP), CALLER-IN FUNCTION CLIP is used to provide the “free of charge” options to control the outputs. By calling the SOLO-KP device from one of the programmed telephone numbers, triggering the Outputs is possible. All KPAx and KPBx telephone numbers are at the same time used as intercom numbers and as Caller ID numbers. -
Page 32: Event Loging
SOLO-KP (LCD) INSTALLATION MANUAL Example: Direct programming on the SIM card SOLO-KP PROGRAMMING TABLE Name Number Description CLPEN Enable CLIP functionality CLPOU CLIP control output 2 CLPI No input activation condition CLP1 040414414 CLIP number 1 CLP2 042340880 CLIP number 2 Table 25: CLIP parameters example. -
Page 33: Special Sms Commands
SOLO-KP (LCD) INSTALLATION MANUAL Name Comment LOGN Number of log events for printing out LOGI Log interface Automatic log clear Table 26: LOG parameters. Example: Direct programming on the SIM card SOLO-KP PROGRAMMING TABLE Name Number Description LOGN 5 log events will be printed out on PLOG command LOGI Nonvolatile memory on SOLO-KP Log is auto cleared when full... -
Page 34: Table 28: Sms Commands
SOLO-KP (LCD) INSTALLATION MANUAL 9.13.5 MRES command Command is used to manually restart GSM module on SOLO-KP device. 9.13.6 SSRES command Command is used to manually restart SOLO-KP device. 9.13.7 Table of parameters Name Comment ORC1 Control of output 1 ORC2 Control of output 2 SDCLR... -
Page 35: Print-Out Of The Parameters
SOLO-KP (LCD) INSTALLATION MANUAL 10 PRINT-OUT OF THE PARAMETERS The authorized user can check the settings of ALL parameters on the SOLO-KP. 10.1 RECEIVE ALL PARAMETERS (PALL) By sending this command to SOLO-KP you receive SMS messages with all parameters that are currently programmed in the unit: ;PALL;... -
Page 36: Receive Output Filter Value (Pod)
SOLO-KP (LCD) INSTALLATION MANUAL 10.8 RECEIVE OUTPUT FILTER VALUE (POD) By sending this command to SOLO-KP you receive SMS message with all currently programmed direct output links (OD1 – OD3): ;POD; 10.9 RECEIVE DELAY BEFORE DIAL VALUE (PDD) By sending this command to SOLO-KP you receive SMS message with all currently programmed Input filters (DD1 –... -
Page 37: Receive All Clip Parameters (Pclp)
SOLO-KP (LCD) INSTALLATION MANUAL 10.15 RECEIVE ALL CLIP PARAMETERS (PCLP) By sending this command to SOLO-KP you receive SMS message with all currently programmed CLIP functionality related parameters ( CLPEN, CLPOU, CLPI, CLPx): ;PCLP; User can use ;PCLP=x,y; to limit the number of CLIP numbers to be printed. x = start number NOTE y = end number... -
Page 38: Receive Spin Access Codes Parameters (Pspin)
SOLO-KP (LCD) INSTALLATION MANUAL 10.19 RECEIVE SPIN ACCESS CODES PARAMETERS (PSPIN) By sending this command to the device you receive SMS message with all currently programmed SPIN parameters: ;PSPIN; User can use ;PSPIN=x,y; to limit the number of SPIN numbers to be printed. x = start number y = end number NOTE... -
Page 39: Changing Parameters Using The Sms Commands
SOLO-KP (LCD) INSTALLATION MANUAL 11 CHANGING PARAMETERS USING THE SMS COMMANDS All programming parameters for SOLO-KP can also be sent by SMS command. Each SMS command should start and stop with semicolon. If the confirmation SMS is needed, put “+” at the beginning of the command SMS. -
Page 40: Default Settings On Solo-Kp
SOLO-KP (LCD) INSTALLATION MANUAL 12 DEFAULT SETTINGS ON SOLO-KP SOLO-KP PROGRAMMING TABLE Name Default Value Short Description Telephone number 1 Empty Telephone number 1 Empty Empty Telephone number 2 Empty Telephone number 3 Empty Telephone number 4 Input 1 control Input 2 control Output 1 mode Output 2 mode... -
Page 41: Table 30: Solo-Kp Default Settings
SOLO-KP (LCD) INSTALLATION MANUAL SOLO-KP PROGRAMMING TABLE Name Default Value Short Description Connection time out value LOGN Number of log events for printing out LOGI Log interface Automatic log clear Auto dial functionality ( Call TN1 ) ARST Automatic reset timeout “EUR”... -
Page 42: Parameters Print-Out Commands
SOLO-KP (LCD) INSTALLATION MANUAL 13 PARAMETERS PRINT-OUT COMMANDS SOLO-KP PROGRAMMING TABLE Name Short Description Prints all parameters available on SOLO-KP. PALL Prints SW version of SOLO-KP. Prints GSM network signal quality of SOLO-KP. Prints TNx numbers. Prints LNx links. Prints INx parameters. Prints IDx parameters. -
Page 43: Technical Specifications
SOLO-KP (LCD) INSTALLATION MANUAL 14 TECHNICAL SPECIFICATIONS Description Value 12,0 – 20,0 V AC or Power Supply 12,0 – 24,0 V DC (1,0 – 2,0A) Current consumption - peak Current consumption - transmitting mode 250mA Current consumption - idle mode 80mA Quad band GSM module 850/900/1800/1900 MHz... -
Page 44: Contacts
SOLO-KP (LCD) INSTALLATION MANUAL 15 CONTACTS MARS COMMERCE d.o.o. MIRKA VADNOVA 19 4000 KRANJ SLOVENIA TEL: 00 386 4 280 74 00 E-MAIL: info@mars-commerce.com WEB SITE: www.mars-commerce.com SALES E-MAIL: sales@mars-commerce.com Page 44...
Need help?
Do you have a question about the SOLO–KP and is the answer not in the manual?
Questions and answers