Adjusting The Amplifier's Audio; Other Hdmi ® Cec Control Functions; Using The Hdmi Settings Feature; Viewing The Hdmi ® Signal Information - Toshiba 32TL515U Owner's Manual

Adjusting the amplifier's audio

Using the TV's remote control, you can adjust or mute
the sound volume of your amplifier.
• VOL adjust the volume level.
VOL
• turns off the sound.
Note: This feature is available when Amplifier Control is set
to On.
1
> Settings > PREFERENCES > HDMI-CEC
Control Setup > .
O K
2
Press B or b to highlight Speaker Preference.
3
Press C or c to select Amplifier.
Note: Confirm that a connected HDMI
(such as DVD player, etc.) is selected for the Amplifier
input source.
Note:
• You can also use this function when the amplifier is
connected to the TV's DIGITAL AUDIO OUT terminal
(not HDMI connection). Select a digital audio input mode
on the amplifier.
• These functions depend on the device connected.
Other HDMI ® CEC Control functions
When Enable HDMI-CEC Control and all items in the
HDMI-CEC Control Setup menu are set to On, the
following functions will be enabled.
Item Description
TV Auto If an HDMI
Power TV turns on automatically.
If the TV is turned off, it will send a
Auto Standby message to turn off all of the HDMI
devices connected to the TV.
If Amplifier Control is set to On, you can
Amplifier
adjust the sound volume or turn off the
Control
sound using the remote control.
From this item, you can set your audio
output preference to the TV speakers or
the amplifier. When this item is set to
Amplifier, the remote control can be used
Speaker
to adjust or mute the volume of the
Preference
audio. This item will not be available and
set to TV Speakers automatically unless
an HDMI ®
receiver is connected.
Note: When you turn on the amplifier, change its input
source, or adjust the sound volume, the sound will be
output from the amplifier's speakers even if TV Speakers
has been selected. Turn the TV off and on again to output
the sound from the TV speakers.
48
Chapter 6: Basic features
®
CEC device
® CEC device is turned on, the
® CEC
CEC compatible audio
Using the HDMI ®
Note: If some HDMI legacy sources do not work properly
with your HDMI TV, set INSTAPORT
setting should allow your HDMI legacy source to operate
properly with your TV.
Mode (default setting) Description
Reduces the lag time when
™
INSTAPORT : On
switching HDMI sources.
Adjusts the RGB full range signal
automatically.
When Limited is selected, the RGB
RGB Range: Auto
output signal is output in the range
of 16 to 235. When Full is selected,
the RGB output signal is output in
the range of 0 to 255.
The RGB Range setting requires appropriate HDMI
source devices. If your HDMI source device does not
support this feature, the TV may not work properly
when it is enabled.
Note: If your HDMI connection is capable of 1080p and/or
your TV is capable of refresh rates greater than 60 Hz, you
will need a High Speed HDMI
DVI cables may not work properly with this mode.
1
Select the appropriate HDMI input mode (HDMI 1,
HDMI 2, HDMI 3, or HDMI 4).
2
> Settings > PREFERENCES > AV
Connection > .
O K
3
Press B or b to select HDMI Settings. Press
4
Press B or b to select an item.
5
Press C or c to select a setting.
Viewing the HDMI
information
1
> Settings > PREFERENCES > HDMI
Information Display.
Press C or c to select On. Press Q. The normal
2
banner and signal information banner appear.
Note:
• The signal information banner will appear when this
feature is set to On and you watch an HDMI input.
Q
• If you press when this feature is set to Off, only the
normal banner will appear.
settings feature
™
to Off. Adjusting this
® cable. Conventional HDMI/
.
O K
® signal