Advertisement
Table of Contents
- 1 Entering, Displaying, and Editing the Equation
- 2 Scientific Calculations
- 3 Statistical Calculations
- 4 Drill Mode
- 5 Complex Number Calculations
- 6 Matrix Calculations
- 7 List Calculations
- 8 Equation Solvers
- 9 Errors and Calculation Ranges
- 10 Battery Replacement
- 11 Specifications
- 12 For more Information about Scientific Calculators
- Download this manual
ENGLISH
SCIENTIFIC CALCULATOR
EL-W506
EL-W516
EL-W546
MODEL
OPERATION MANUAL
PRINTED IN CHINA / IMPRIMÉ EN CHINE / IMPRESO EN CHINA
07HGK (TINSE1307EHZZ)
INTRODUCTION
Thank you for purchasing the SHARP Scientifi c Calculator
Model EL-W506/W516/W546.
About the calculation examples (including some formulas
and tables), refer to the calculation example sheet. Refer to
the number on the right of each title in the manual for use.
After reading this manual, store it in a convenient location for
future reference.
Notes:
• Some of the models described in this manual may not be
available in some countries.
• This product uses a period as a decimal point.
Operational Notes
• Do not carry the calculator around in your back pocket, as it
may break when you sit down. The display is made of glass
and is particularly fragile.
• Keep the calculator away from extreme heat such as on a
car dashboard or near a heater, and avoid exposing it to
excessively humid or dusty environments.
• Since this product is not waterproof, do not use it or store
it where fl uids, for example water, can splash onto it.
Raindrops, water spray, juice, coffee, steam, perspiration,
etc. will also cause malfunction.
• Clean with a soft, dry cloth. Do not use solvents or a wet cloth.
• Do not drop it or apply excessive force.
• Never dispose of batteries in a fi re.
• Keep batteries out of the reach of children.
• For the sake of your health, try not to use this product for
long periods of time. If you need to use the product for an
extended period, be sure to allow your eyes, hands, arms,
and body adequate rest periods (about 10–15 minutes
every hour).
If you experience any pain or fatigue while using this
product, discontinue use immediately. If the discomfort
continues, please consult a doctor.
• This product, including accessories, may change due to
upgrading without prior notice.
NOTICE
• SHARP strongly recommends that separate permanent
written records be kept of all important data. Data may be
lost or altered in virtually any electronic memory product
under certain circumstances. Therefore, SHARP assumes
no responsibility for data lost or otherwise rendered
unusable whether as a result of improper use, repairs,
defects, battery replacement, use after the specifi ed
battery life has expired, or any other cause.
• SHARP will not be liable nor responsible for any incidental
or consequential economic or property damage caused
by misuse and/or malfunctions of this product and its
peripherals, unless such liability is acknowledged by law.
♦ Press the RESET switch (on the back), with the tip of a
ball-point pen or similar object, only in the following cases:
• When using for the fi rst time
• After replacing the battery
• To clear all memory contents
• When an abnormal condition occurs and all keys are
inoperative
Do not use an object with a breakable or sharp tip. Note that
pressing the RESET switch erases all data stored in memory.
If service should be required on this calculator, use only a
SHARP servicing dealer, SHARP approved service facility, or
SHARP repair service where available.
Hard Case
Remove the hard case, holding it with your fi ngers in the
positions shown below.
DISPLAY
Symbol
Dot
matrix
display
Mantissa
Exponent
• During actual use, not all symbols are displayed at the same time.
• Only the symbols required for the usage currently being explained
are shown in the display and calculation examples in this manual.
/
:
Indicates that some contents are hidden in the
/
directions shown.
Appears when @ is pressed, indicating that the
2ndF:
functions shown in orange are enabled.
Indicates that H has been pressed and the
HYP:
hyperbolic functions are enabled. If @ > is
pressed, the symbols 2ndF HYP appear, indicating that
inverse hyperbolic functions are enabled.
ALPHA: Indicates that ;, x or t has been pressed,
and entry (recall) of memory contents and recall of
statistics can be performed.
DEG/RAD/GRAD: Indicates angular units.
BUSY: Appears during the execution of a calculation.
W-VIEW: Indicates that the WriteView editor is selected.
M:
Indicates that a numerical value is stored in the
independent memory (M).
/
: Indicates the mode of expression for results in CPLX mode.
ENG/SCI/FIX/N2/N1: Indicates the notation used to display a
value and changes by SET UP menu. N1 is displayed
on-screen as “NORM1”, and N2 as “NORM2”.
BEFORE USING THE CALCULATOR
When using for the fi rst time, press the RESET switch (on the
back), with the tip of a ball-point pen or similar object.
Adjusting the Display Contrast
Press @ J 3, then + or & to adjust the
contrast. Press j to exit.
Power On and Off
Press j to turn the calculator on. The data that was on-
screen when the power was turned off will appear on the display.
Press @ o to turn the calculator off.
Key Notations Used in this Manual
In this manual, key operations are described as follows:
x
e
: @ "
To specify
To specify ln: i
To specify E: ; E
• Functions that are printed in orange above the key require
@ to be pressed fi rst before the key. When you specify the
memory, press ; fi rst. Numbers for input values are not
shown as keys, but as ordinary numbers.
• Functions that are printed in gray adjacent to the keys are
effective in specifi c modes.
• The multiplication operator “×” is differentiated from the letter
“X” in this manual as follows:
To specify the multiplication operator: k
To specify the letter “X”: ; X
The WriteView and Line Editors
This calculator has the following two editors in NORMAL mode:
WriteView and Line. You can select between them in the SET UP
menu.
The WriteView editor (default)
The Line editor
Notes:
• The WriteView Editor is only available in NORMAL mode.
• In certain calculation examples, where you see the o
symbol, the key operations and calculation results are shown
as they would appear in the Line editor.
Clearing the Entry and Memories
Operation
A–F,
F1–F4,
4
Entry
matA–D*
3
ANS STAT*
5
(Display)
L1–L4*
1
2
M, X, Y*
D1–D4*
j
○
×
×
×
×
×
@ Z
○
×
×
○
○
○
○
×
×
×
×*
6
○
Mode selection (b)
@ P 0*
7
○
×
×
×
×
×
@ P 1 0*
7
○
○
○
○
○
○
@ P 2 0*
7,
8
*
○
○
○
○
○
○
8
RESET switch *
○
○
○
○
○
○
○: Clear
×
: Retain
*1 Press j x and then choose a memory to clear one
variable memory.
*2 Formula memories and defi nable memories. See “Memory
Calculations”.
*3 Statistical data (entered data)
*4 Matrix memories (matA, matB, matC, and matD)
*5 List memories (L1, L2, L3, and L4)
*6 Cleared when changing between sub-modes in STAT mode.
*7 See “Memory clear key”.
*8 The username you stored using the name display function will
be cleared as well.
Memory clear key
Press @ P to display the menu.
• To initialize the display settings,
press 0. The parameters are
set as follows:
• Angular unit: DEG
• Display notation: NORM1
• N-base: DEC
• To clear all variables and memories (A−F, M, X, Y, F1−F4, D1−D4,
ANS, STAT, matA−D, and L1−L4) at once, press 1 0.
• To RESET the calculator, press 2 0. The RESET
operation will erase all data stored in memory and restore
the calculator’s default settings. You can do the same thing by
pressing the RESET switch on the back of the calculator.
Mode Selection
→
d
NORMAL mode: b 0 (default)
Used to perform arithmetic operations and function calculations.
STAT mode: b 1
Used to perform statistical operations.
DRILL mode: b 2
Used to practice math and multiplication table drills.
CPLX mode: b 3
Used to perform complex number calculations.
MATRIX mode: b 4
Used to perform matrix calculations.
LIST mode: b 5
Used to perform list calculations.
EQUATION mode: b 6
Used to solve equations.
Advertisement
Table of Contents
Related Manuals for Sharp EL-W506B
Summary of Contents for Sharp EL-W506B
- Page 1 • When an abnormal condition occurs and all keys are inoperative Do not use an object with a breakable or sharp tip. Note that pressing the RESET switch erases all data stored in memory. If service should be required on this calculator, use only a SHARP servicing dealer, SHARP approved service facility, or SHARP repair service where available.
-
Page 2: Entering, Displaying, And Editing The Equation
SET UP Menu Press @ J to display the SET UP menu. Press j to exit the SET UP menu. Determination of the angular unit The following three angular units (degrees, radians, and grads) can be specifi ed. @ J 0 0 (default) DEG (°): RAD (rad): @ J 0 1 GRAD (g): @ J 0 2... -
Page 3: Scientific Calculations
The CATALOG Menu Using the CATALOG menu, you can select functions and variables that are available for what you are doing in the currently selected mode. To display the CATALOG menu, press N 0. • Press u or d to move the cursor ( ) and press e to select. - Page 4 Defi nable memories (D1–D4) You can store functions or operations in defi nable memories (D1–D4). • To store a function or operation, press x, followed by a defi nable memory key (I, J, K, or L), followed by the operation you want to store. Menu-related operations, such as @ J, cannot be stored.
-
Page 5: Statistical Calculations
Calculations Using Engineering Prefi xes Calculation can be executed in NORMAL mode (excluding N-base) using the following 9 types of prefi xes. Prefi x Operation Unit N 3 0 (kilo) N 3 1 (Mega) N 3 2 (Giga) N 3 3 (Tera) N 3 4 (milli) -
Page 6: Complex Number Calculations
5. Enter your answer. If you make a mistake, press j or N to clear any entered numbers, and enter your answer again. 6. Press e. • If the answer is correct, “ ” appears and the next question is displayed. •... -
Page 7: List Calculations
trans matrix name Returns the matrix with the columns transposed to rows and the rows transposed to columns. mat list Creates lists with elements from the (N 7) left column of each matrix. (matA L1, matB L2, matC L3, matD L4) Mode changes from MATRIX mode to LIST mode. -
Page 8: Battery Replacement
Operating temperature: 0°C–40°C (32°F–104°F) External dimensions: Weight: Accessories: FOR MORE INFORMATION ABOUT SCIENTIFIC CALCULATORS Visit our Web site. http://sharp-world.com/calculator/ Fig. 1 Fig. 2 Scientifi c calculations, complex number calculations, equation solvers, statistical calculations, etc. Math Drill and Multiplication Table 32 dot matrix liquid crystal... - Page 9 EL-W506 EL-W516 EL-W546 CALCULATION EXAMPLES EXEMPLES DE CALCUL ANWENDUNGSBEISPIELE EJEMPLOS DE CÁLCULO EXEMPLOS DE CÁLCULO ESEMPI DI CALCOLO REKENVOORBEELDEN PÉLDASZÁMÍTÁSOK PŘÍKLADY VÝPOČTŮ RÄKNEEXEMPEL LASKENTAESIMERKKEJÄ UDREGNINGSEKSEMPLER CONTOH-CONTOH PERHITUNGAN PRINTED IN CHINA / IMPRIMÉ EN CHINE / IMPRESO EN CHINA 07HGK (TINSZ1308EHZZ) 100000 j 100000 z 3 [NORM1]...
- Page 10 @ G ; X m 4 r & 0.5 ; X @ 1 + 6 ; X A r 2 = = 0.00002 l l N 3 H 0.001 = = 0.001 @ G ; X m 4 & 0.5 ; X @ 1 + 6 ;...
- Page 11 z r g h / d n 4 p x C BIN j @ / 25 DEC (25) 11001 @ h 1AC HEX (1AC) 110101100 @ z ( (1010 100) 1010 & 100 ) k 11 [BIN] 10010 BIN 1111111001 BIN (111) →...
- Page 12 b 1 1 DATA 2 H 5 _ 12 H 24 _ 21 H 40 H 3 15 H 25 _ ? 3 @ U ´ ? 46 @ V ´ b 1 2 DATA 12 H 41 _ 8 H 13 _ 5 H 2 _ 23 H 200 _ DATA SET= 15 H 71 _...
- Page 13 b (MATRIX) N 2 2 2 e ⇒ matA 1 e 2 e 3 e 4 e j N 4 0 N 2 e 3 e 1 e 2 e 6 e ⇒ matB j N 4 1 j N 1 0 k matA matB N 1 1 =...
- Page 14 Function Fonction Funktion zulässiger Bereich Función Função Funzioni Functie Függvény Megengedett számítási tartomány Funkce Dynamický rozsah Funktion Definitionsområde Funktio Funktion Fungsi DEG: | (tan RAD: , cos , tan (tan GRAD: | (tan –1 –1 , cos –1 –99 , log , log •...
- Page 15 Wenn Sie dieses Produkt für gewerbliche Zwecke genutzt haben und nun entsorgen möchten: Bitte wenden Sie sich an Ihren SHARP Fachhändler, der Sie über die Rücknahme des Produkts informieren kann. Möglicherweise müssen Sie die Kosten für die Rücknahme und Verwertung tragen. Kleine Produkte (und kleine Mengen) können möglicherweise bei Ihrer...
- Page 16 Als u het product voor zakelijke doeleinden heeft gebruikt en als u dit wilt weggooien: Neem contact op met uw SHARP distributeur die u inlichtingen verschaft over de terugname van het product. Het kan zijn dat u een afvalverwijderingsbijdrage voor de terugname en recycling moet betalen.