Subscribe to Our Youtube Channel
Related Manuals for Motomaster ELIMINATOR 011-3008-0
Summary of Contents for Motomaster ELIMINATOR 011-3008-0
- Page 1 ® model no. 011-3008-0 12 V BATTERY TESTER & Charging System Analyzer IMPORTANT: SAVE THESE INSTRUCTIONS. INSTRUCTION This manual contains important safety MANUAL and operating instructions. 0099002016-00...
- Page 2 11-3008-0 | contact us 1-888-942-6686 This MotoMaster Eliminator product carries a one (1) year warranty against defects in workmanship and materials. At its discretion, MotoMaster Canada agrees to have any defective part(s) repaired or...
- Page 3 ® TABLE OF CONTENTS Safety Safety Information Personal Safety Precautions Preparing To Test Operation Battery Test Starter System Test Charging System Test Troubleshooting Technical Specifications Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as operating and maintenance advice.
- Page 4 headline bars model no. 011-3008-0 | contact us 1-888-942-6686 SAFETY INFORMATION This manual will show you how to use your tester safely and effectively. Please read, understand and follow these instructions and precautions carefully, as continuation tabs this manual contains important safety and operating instructions.
- Page 5 ® DO NOT disassemble the tester; take it to a • qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or electric shock. Follow these instructions and those published by • the battery manufacturer and the manufacturer of any equipment you intend to use in the vicinity of the battery.
- Page 6 headline bars model no. 011-3008-0 | contact us 1-888-942-6686 NEVER smoke or allow a spark or flame in the • vicinity of the battery or engine. Be extra cautious, to reduce risk of dropping a • metal tool onto battery. It might spark or short- continuation tabs circuit battery or other electrical part that may cause explosion.
- Page 7 ® OPERATION IMPORTANT: For testing 12 V batteries only. Suggested operational range 32°F (0°C) to 122°F (50°C) ambient air temperature. BATTERY TEST 1. Turn off the ignition, all accessories and any loads. Close all vehicle doors and the trunk lid. 2.
- Page 8 headline bars model no. 011-3008-0 | contact us 1-888-942-6686 8. Select the battery rating. Press ▲or ▼to select: CCA (Cold Cranking Amps) CA [MCA] (Cranking Amps [Marine Cranking Amps]) En (a European standard) continuation tabs IEC (International Electrotechnical Commission standard) din (Deutsches Institut für Normung Standard) Press when the correct rating type...
- Page 9 ® Press when the correct CCA rating is displayed, to begin the test. NOTE: If the display shows CHA- (“Is tested and select ▲or ▼ battery charged?”) press to choose yes or no, and then press 10. When the test is complete, the battery tester will display the CCA and one of the following results: OK (green LED lights) –...
- Page 10 headline bars model no. 011-3008-0 | contact us 1-888-942-6686 continuation tabs RECHARGE & RETEST (yellow and red LED lights) – The battery is discharged. The battery condition notes cannot be determined until it is fully charged. Recharge and retest the battery. If the reading is the same, the battery should be replaced immediately.
- Page 11 ® ERROR (right-hand red LED lights and Err shows on the screen) – The clamps are not connected properly OR the tested battery is larger than maximum testing CCA capacity. 11. Press to return to the beginning of the test, or remove the clamps from the battery posts to end the test.
- Page 12 headline bars headline bars model no. 011-3008-0 | contact us 1-888-942-6686 8. Start the engine. Read the voltage after cranking the starter. 9. When the test is complete, the tester will display one of the following results: continuation tabs continuation tabs notes notes OK (green LED lights) –...
- Page 13 ® CHARGING SYSTEM TEST 1. After starter test, press for charging system test. The display will show CHAr. Press to read live voltage. 2. Rev the engine to 1200-1500 rpm. Read the voltage while the car is running. 3. The tester will display the battery’s voltage and one of the following results: OK (green LED lights) –...
- Page 14 headline bars model no. 011-3008-0 | contact us 1-888-942-6686 continuation tabs CHARGING VOLTAGE IS HIGH (red LED lights) – Check the regulator. notes 4. Following the charging system at idle, continue the charging system test with test loads. Turn on the blower to high (heat), high beam headlights and rear defogger.
- Page 15 ® CHARGING VOLTAGE IS LOW (yellow LED lights) – Check connections, wiring and alternator. CHARGING VOLTAGE IS HIGH (red LED lights) – Check the regulator. 6. To end the test, turn engine off and remove the clamps from the battery posts.
- Page 16 headline bars model no. 011-3008-0 | contact us 1-888-942-6686 PROBLEM POSSIBLE CAUSE SOLUTION The display is The clamps are Clean terminals and blank. not connected rock clamps back properly to a and forth to ensure continuation tabs battery OR proper connection the voltage of the to battery.
- Page 17 ® PROBLEM POSSIBLE CAUSE SOLUTION The display The voltage Ensure no loads flickers or of the battery are being drawn shows - - - - . being tested is from the battery. unstable. If the battery was recently charged, wait 15-30 minutes to let the battery voltage stabilize, then...
- Page 18 TECHNICAL SPECIFICATIONS Battery load test 12 V Charging system test 12 V continuation tabs Starting system test 12 V Testing voltage range 7-15 V DC Operating range 100-1200 CCA (SAE) notes warnings Made in Taiwan Motomaster Canada Toronto, Canada M4S 2B8...
Need help?
Do you have a question about the ELIMINATOR 011-3008-0 and is the answer not in the manual?
Questions and answers