Advertisement
Quick Links
.
mr
steam
___________________________________________________________________________________
The CU Alarm is an audible alarm
that sounds in the event the
steam room maximum set
temperature is exceeded or if the
CU-SteamStop button has been
pressed.
The CU Alarm may be mounted
outside the steam room in a
location that will alert an
attendant and/or user to an
over-temperature condition.
Review local codes for mounting location
as required
.
The CU Alarm shall not be
WA R N I N G
mounted inside the steam room.
Please Read These
WA R N I N G
Instructions Carefully Before Using this
Product. The 115VAC CU Alarm must be field
set to the desired dBa sound output level and
alarm tone before installation. This is done
by adjusting a four position switch in accor-
dance with these instructions. Incorrect set-
tings will result in improper performance.
IMPORTANT NOTE: As you follow these instructions, you will notice warning and caution symbols.
This information is important for the safe and efficient installation and operation of this generator.
These are types of potential hazards that may occur during this installation and operation:
states a hazard may cause serious injury or death if precautions are not followed.
C A U T I O N
signals a situation where minor injury or product damage may occur if you do not follow instructions.
WA R N I N G
.
mr
steam
®
Sussman-Automatic Corp.
®
info@mrsteam.com
www.mrsteam.com
®
43-20 34th Street
Long Island City, NY 11101
: 718-937-4500
: 718-472-3256
TEL
FAX
d B A R A T I N G S
Tone
Horn
Bell
March Time Horn 85
*Code-3 Horn
*Code-3 Tone
Slow Whoop
Siren
Hi/Lo
*See note on Page 3
9410 S. La Cienega Blvd.
Inglewood CA 90301
: 310-216-6565
: 310-216-2944
TEL
FAX
CU ALARM
dBA Reverberant
at 10 feet
High
Standard
88
82
82
75
79
85
75
79
75
88
82
85
82
82
79
PUR 100452 Rev 4/10
Advertisement
Related Manuals for mr. steam CU Series
Summary of Contents for mr. steam CU Series
- Page 1 steam ® CU ALARM ___________________________________________________________________________________ The CU Alarm is an audible alarm that sounds in the event the steam room maximum set temperature is exceeded or if the CU-SteamStop button has been pressed. The CU Alarm may be mounted outside the steam room in a location that will alert an attendant and/or user to an over-temperature condition.
- Page 2 steam ® CU ALARM _____________________________________________________________________________________________________________________________ MAKE SURE THAT ALL FUSES USED ON SIGNALING WA R N I N G CIRCUITS ARE RATED TO HANDLE THE MAXIMUM INRUSH OR PEAK CURRENT FROM ALL APPLIANCES ON THOSE CIRCUITS. FAILURE TO DO THIS MAY RESULT IN LOSS OF POWER TO THE SIGNALING CIRCUIT AND THE FAILURE OF ALL APPLIANCES ON THAT CIRCUIT TO OPERATE.
- Page 3 steam ® CU ALARM _____________________________________________________________________________________________________________________________ STEP 1: Figure 2: SW1 Switch Set desired dBA sound output by setting POS 1 of the four position switch (SW1). (refer to Figure 2 and Table 2). STEP 2: Slide Here for (0) Set desired alarm tone by setting the four-posi- Slide Here for (1) tion switch (SW1).
- Page 4 steam ® CU ALARM _____________________________________________________________________________________________________________________________ WIRING THE ALARM TO A MR.STEAM CU COMMERCIAL STEAM GENERATOR: WA R N I N G SHUT OFF ALL POWER AT BREAKER BEFORE STARTING THE INSTALLATION. ELECTRIC SHOCK CAN CAUSE DEATH OR SERIOUS INJURY. IMPORTANT NOTE: All electrical wiring is to be installed by a qualified, licensed electrician in accordance with National and local electrical codes.
-
Page 5: Control Supply
steam ® CU ALARM _____________________________________________________________________________________________________________________________ Diagram: CU 360-4500 with 120 Volt F1 Plus Control: Factory Wiring Field Wiring Control Supply 120 Volt 1 PH 60 Hz CU ALARM Control Terminal Block REMOVE JUMPER FOR CU-HL CU ALARM NOTES: 1. This Diagram shall only be used for wiring CU-Alarms. -
Page 6: Surface Mounting
steam ® CU ALARM _____________________________________________________________________________________________________________________________ SURFACE MOUNTING: 4" SQ. X 2-1/8" Deep IMPORTANT NOTE: All electrical wiring is to be ELECTRICAL BOX installed by a qualified, licensed electrician in accordance with National and local electrical codes. SIGNAL Review local codes for mounting location as required DO NOT mount the CU ALARM WARNING inside the steam room.
Need help?
Do you have a question about the CU Series and is the answer not in the manual?
Questions and answers