Summary of Contents for PLAYSTAR PlayAction Decorative Kit
Page 1
Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines in your original playset, at www.playstarinc.com, or at 1-888-752-9782.
When attaching activities, please take note of locations which would prohibit secure fastening and/or allow any protrusions of deck screws. RTA and BIY are references to PlayStar playsets. Some construction may require two people. TABLE OF CONTENTS - DECORATIVE KIT Contents .
Page 3
COMPONENTS INCLUDED Sunlight Window (1) Decorate-a-Flag (1) Magnetic Chalkboard (1) Flag Pole (1) ABCDEF Sand Box Roof Stencil Set (1) Seat (1) Cap (1) Design-a-Plaque (1) BOARDS INCLUDED 1" x 4" x 10" (4) 1" x 4" x 6" (2) 2"...
Page 4
Use an ¹ " drill bit for all holes unless noted Note: When the PlayStar logo is showing, the three tabs on the bottom will position the template square with any two edges. When the arrow...
ACCENT DORMER ASSEMBLY STEP 1 Items for (1) 2" x 4" x 15¹⁄ " left board (1) 2" x 4" x 15¹⁄ " right board (1) Roof Cap ¹⁄₈ ¹⁄₈ 15¹⁄₈" " 15¹⁄₈" " (6) #14 x 1¹⁄₄" pan head screws On a flat surface, position boards together as shown.
Page 6
Fig. 1 STEP 3 Items for Mark Edges (1) 2" x 6" x 5¹⁄₄" triangle board (4) #8 x 1¹⁄₂" deck screws top edges with a pencil as shown. Fig. 1 Align triangle board with roof panel boards, marking the Fig.
COUNTRY CUPOLA ASSEMBLY STEP 1 Items for (4) 2" x 4" x 11" boards (2) 1" x 4" x 6" boards (8) #8 x 1¹⁄₂" deck screws On a flat surface, position 2" x 4" x 11" boards together as shown. Position 1" x 4" x 6" centered and flush with the bottom of the “V”...
Page 8
STEP 4 Items for Position board flush at the top and centered side to side on Step 3 Assembly (1) Step 3 Assembly as shown. Secure with #8 x 1¹⁄₂" deck screws. Repeat for the other side. (2) 1" x 4" x 10" boards (4) #8 x 1¹⁄₂"...
Page 9
Set cupola at the desired location. Mark all six edges as shown. Fig. 1 STEP 6 Items for (1) Cupola Template (Pg. 23) Remove cupola. Cut out cupola template. Tape template on the roof, lining up the through the roof. Fig. 2 (1) Cupola Assembly pencil edges.
Page 10
COUNTRY CUPOLA - Roof ³⁄₄ " or Thinner Caution: If your roof boards are ³⁄₄ " or thinner,follow these steps. STOP STEP 7 Items for Flush (2) 1" x 4" x 7⁷⁄ " boards (4) #8 x 1¹⁄₂" deck screws Flush Attach the 1"...
Page 11
This page left blank intentionally - Dormer Template on reverse side that will need to be cut out.
Dormer Template (cut out) used in Step 4 on Page 6. Drill this hole for roof boards 1" or thicker Drill this hole for roof boards ³⁄₄" or thinner TAPE HERE TO ROOF...
Page 14
This page left blank intentionally - Dormer Template on reverse side that will need to be cut out.
FLOWER BOX ASSEMBLY STEP 1 Items for (1) 2" x 4" x 18⁵⁄ " board 6" " 6 Center Center Center Predrill and countersink board at dimensions shown. 6" " 6 ATTERNS STEP 2 Items for (1) 2" x 4" x 18⁵⁄ " board (2) #8 x 2¹⁄₂"...
Page 16
STEP 4 Items for Set Flower Box at desired location. Using the holes pre-drilled in Step 1 as a guide, predrill ¹⁄ " holes. Secure using #8 x 2¹⁄₂" deck screws. (3) #8 x 2¹⁄₂" deck screws Shown on RTA Shown on BIY Note: You will want to locate flower box where there are thicker boards and the 2 ¹⁄₂...
SAND BOX SEAT STEP 1 Items for (1) Sand Box Seat (4) #14 x 1¹⁄₄" pan head screws Position sand box seat as shown and mark holes. Drill ¹⁄ " holes 1" deep into the board. Attach with #14 x 1¹⁄₄" pan head screws. STENCIL SET INSTRUCTIONS 1.
Page 18
SUNLIGHT WINDOW - RTA NARROW STEP 1 Items for on the scoring lines at 90º angle as shown. Fig. 1 For window openings of approximately 20³⁄₄" wide, use a straight edge and fold (1) Sunlight Window (16) #8 x ⁵⁄ " truss head screws Fig.
Page 19
SUNLIGHT WINDOW - RTA WIDE STEP 1 Items for on the scoring lines at 90º angle as shown. Fig. 1 For window openings of approximately 24¹⁄₂" wide, use a straight edge and fold (1) Window (16) #8 x ⁵⁄ " truss head screws Fig.
DECORATE-A-FLAG STEP 1 Items for (1) Flag (1) Flag Pole (1) Zip Tie Insert flag onto the flag pole with sewn edge on top as Your design shown. Secure firmly with the zip tie. Trim the end of the goes here zip tie with scissors flush with the head.
DESIGN-A-PLAQUE STEP 1 Items for (1) Design-a-Plaque (4) #8 x 1" truss head screws Shown on RTA Plaque can be installed horizontal or diagonal. Position plaque at desired location. Secure with #8 x 1" truss head screws. Your design goes here Shown on BIY Your design goes here...
MAGNETIC CHALKBOARD STEP 1 Items for Chalkboard can be installed horizontal or vertical. Position chalkboard at desired location. Secure with #8 x ⁵⁄ " truss head screws. (1) Magnetic Chalkboard (4) #8 x ⁵⁄ " truss head screws Caution: To eliminate finger or head entrapments, all gaps around chalkboard - or to the nearest object - must meet the...
Need help?
Do you have a question about the PlayAction Decorative Kit and is the answer not in the manual?
Questions and answers