Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Maruyama ED2321
Summary of Contents for Maruyama ED2321
- Page 1 Out d p Owe r Equipment � Completely read and understand this manual p rior to usin g this product MARUYAMA OWNER'S OPERATOR'S MANUAL Power Edger ED2321 ED2621 �c,_,~ , ..,., , ... �--"· maruyama E tr a Ord in...
- Page 2 . . Any warranted part, which is scheduled for replacement as, required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part. Maruyama Mfg. Co, Inc. is liable for damages to other engine components caused by the failure of a warranted part still under warranty The purchaser is responsible for the performance of the required maintenance, as defined by Maruyama Mfg Co.
-
Page 4: Federal Emission Control
U. S . EPA stan- dards for the first two years of engine use from the date of sale to the ultimate purchaser. Maruyama Manufacturing Company, Inc. must warrant the emission control system on your small off-road engine for the period of time listed above provided there has been no abuse, neglect or improper maintenance of your small off-road engine. - Page 5 Maruyama Manufacturing Company, Inc .. is liable for damages to other engine components caused by the failure of a warranted part still under warranty.
-
Page 6: California Emission Control
MANUFACTURER'S WARRANTY COVERAGE: The 1995 and later small off-road engines are warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by Maruyama Manufacturing Company, Inc. OWNER'S WARRANTY RESPONSIBILITIES:... -
Page 7: Table Of Contents
Contents Page Page Limited Warranty Statement Mixing Gasoline And Oil . Federal Emission Control . Starting And Stopping California Emission Control Operation Introduction Operating Position Safety Setting Depth of Cut . Operator Safety Maintenance Edger Safety Idle Speed Adjustment Air Filter Fuel Safety Power Edger Operating Safety Fuel Filter . -
Page 8: Introduction
Thank you for purchasing a Maruyama product maintain your product correctly Reading this manual Maruyama, it's distributors, and dealers want you to be will help you and others avoid personal injury and dam completely satisfied with your new product Please feel age to the product Although Maruyama designs, pro... -
Page 10: Fuel Safety
If running problems or excessive vibration occur, cause. . If the cause cannot be determined or is If you are approached while operating the Edger, Allow the engine to cool before refueling stop immediately and inspect the unit for the Drain the tank and run the engine dry before stor... -
Page 11: Safety And Instruction Decals
Do not use the other protective safety devices in place. Edger for any job that is not recommended by Maruyama. Do not put hands or feet near or under any rotating parts. Keep clear at all times. Keep all parts of... -
Page 13: Assembly
Assembly Assembling Engine and Drive Shaft Assembly The drive shaft, clutch drum housing and gearcase a assembled Attach the clutch drum housing to the engine using the four M5 x 20 screws supplied with the unit Engine MS x 20 Screw (4) Shaft Slip the rubber sleeve around the shaft approxi... -
Page 14: Connecting Stop Switch Wires
Connecting Throttle Cable Connecting Stop Switch Wires <___ � Stop Switch Wires� Carburetor Bracket ./ Throttle Cable.� -- -=- ---:----::: ----: -::-- 7---.. Cable Adjus t e r Stop Switch Wires Throttle Stop/Idle Speed Sleeve �' Adjuster Screw Bracket Carburetor Throttle Cam Knob Air Filter Cover Idle Speed... -
Page 16: Before Operation
POTENTIAL HAZARD • Gasoline contains gasses that can build up pressure insi de a gas tank. • Fuel c a n be spra yed o n you when removing gas cap. HOW TO AVOID THE HAZARD • Remove fuel cap slowly to avoid injury om fuel spray. -
Page 18: Starting And Stopping
Note: Never use a mixing ratio less than Fill the tank only to within 1/4-1/2 inch (6 mm-13 50:1 regardless of the oil package mm) from the top of the tank Avoid filling to the mixing instructions.. Ratios less than top of the tank filler neck 50:1, (for example, 60:1, 80:1, 100:1), reduce the amount of lubrication to... -
Page 20: Operation
• Foreign objects can be thrown by Edger. • Contact with thrown objects can cause personal injury. Operation Operating Position Before using the Edger, check the following: WARNING POTENTIAL HAZARD Hearing________ Eye Protection Protection RightArm � WHAT CAN HAPPEN Slightly Bent - Left Arm Fully "- Extended, Hand... -
Page 21: Setting Depth Of Cut
• Always wear gloves and protective cloth warranty repairs must be per ormed by a dealer or· ing when operating the Edger. service center authorized by Maruyama Manufacturing Company, Inc. The use of parts that are not equivalent in per ormance and durability to authorized parts may impair the effectiveness of the •... -
Page 22: Air Filter
If idle speed adjustment is necessary, and after WARNING adjustment the Edger blade rotates or the engine stalls, stop using the Edger immediately! Contact your local authorized Maruyama Dealer for assistance and servicing, Air Filter Maintenance Interval • The air filter should be cleaned daily, or more often when working in extremely dusty condi... -
Page 23: Fuel Filter
The fuel filter should be replaced after every 100 hours • The spark plug should be removed from the of operation. engine and checked after each 25 hours of opera tion • Replace the spark plug after every 100 hours of operation. -
Page 24: Cylinder Cooling Fins
• Muffler· surface becomes hot when Edger is in operation and remains hot for some time after the engine is shut off. aces could • Contact with hot muffler sur cause a burn. • Make sure the muffler is cool before inspec ting and cleaning the spark arrester. -
Page 25: Exhaust Muffler
Flexible Drive Shaft Maintenance Loosen the knob and lift off the cylinder cover Remove and clean the tail, gasket and spark Maintenance Interval aHester with a safety solvent and a stif brush. If any part cannot be thoroughly cleaned, it must be The Edger uses a flexible drive shaft inside the drive replaced. -
Page 26: Gearcase Maintenance
/ Plug Hole _.__L�il'-; = Watch for The Maruyama Edger will provide maximum perfor Grease here Bearing Lube mance for many, many hours if it is maintained proper (P/N 211337) ly Good maintenance includes regular checking of all... -
Page 28: Troubleshooting
Clean or replace air filter Cutting Dirty air filter Clean spark arrester or exhaust port. Clogged spark arrester or exhaust port. fllrther assistance is required, contact your local authorized Maruyama seI' v ice dealer,, Maintenance Period Every Every Every •... -
Page 29: Specifications
Specifications ED2621 ED2321 13 3Ibs (6.0kg) Weight *1 13.1 lbs. (5 9 kg) 25.4cc Engine Displacement 22 5 cc Curved full support Shaft Blade Typ 8" spring steel Carburetor Walbro Diaphragm Type Ignition System Solid State 0.53 qts (05 £) 0.63 qts (0.6 £)
Need help?
Do you have a question about the ED2321 and is the answer not in the manual?
Questions and answers