Related Manuals for ELPRO ECOLOG-PRO Series
Summary of Contents for ELPRO ECOLOG-PRO Series
- Page 1 ECOLOG-PRO Radio Modules ECOLOG-PRO RBR ECOLOG-PRO 1NTR Operation Manual PM | PHIOSL 1000356V01 DOC - ECOLOG-PRO RBR and 1NTR - Operation Manual_EN | Page 1 / 13...
-
Page 2: Table Of Contents
Contents System Overview ..........................4 Communication Module ECOLOG-PRO RBR ..................5 Measurement Module ECOLOG-PRO 1NTR ..................7 Disposal ............................10 Declaration of Conformity ......................11 1000356V01 DOC - ECOLOG-PRO RBR and 1NTR - Operation Manual_EN | Page 2 / 13... - Page 3 Conformity and Symbols Used Hereby, ELPRO-BUCHS AG declares that the radio equipment type ECOLOG-PRO 1NTR 868 MHz is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available in chapter 5 of this document or at the following internet address: https://www.elpro.com/fileadmin/Docs/Quality_Documents/ECOLOG-PRO_1NTR_DOC-...
-
Page 4: System Overview
The measured values are transmitted to a monitoring software (ELPRO Cloud), which stores and analyzes the data, provides alerts if alarm limits are violated, and generates reports. The system provides superior visibility and transparency in meeting GxP requirements. -
Page 5: Communication Module Ecolog-Pro Rbr
Communication Module ECOLOG-PRO RBR Functional characteristics: The ECOLOG-PRO RBR module is the link between the wireless measurement modules of the ECOLOG- PRO series and the monitoring software. The data is transferred to the software over the Internet using an Ethernet connection (via RJ45 plug). Power supply •... - Page 6 2a. Once the connection to the network is made, the left LED will turn yellow, indicating that it is connected to the network 2b. The left LED will ultimately turn green, indicating that the module is connected to ELPRO Cloud.
-
Page 7: Measurement Module Ecolog-Pro 1Ntr
Measurement Module ECOLOG-PRO 1NTR Functional characteristics: ECOLOG-PRO 1NTR is a measurement module with an internal temperature sensor. Communication from this module with the ECOLOG-PRO RBR is via radio signal. Power supply 2 AAA Alkaline or LiFe (lithium-iron) batteries SAFETY INSTRUCTIONS! Improper use or misuse of batteries may result in leakage of battery fluid or, in the worst case, explosion and/or fire. - Page 8 The interval of the flashing light is 10s. How to connect: Make sure that you have defined the sensor's settings in the ELPRO Cloud software and that the "Add sensor" wizard shows the image displayed above. This gives you a 10 minutes time frame to connect your module via the following steps: 1.
- Page 9 3. Bring the measurement module ECOLOG-PRO 1NTR in close proximity (approximately 1 meter) to an ECOLOG-PRO RBR connected to ELPRO Cloud. 4. Press and hold the "Connect" button inside the measurement module for more than 3 seconds. The left LED will blink red 3 times.
-
Page 10: Disposal
Disposal a) Product Electronic devices are recyclable and do not belong in the household waste. Dispose of the product at the end of its service life in accordance with applicable laws. Remove any batteries and dispose of them separately from the product. b) Batteries You are legally obliged to dispose of all used batteries according to applicable laws;... -
Page 11: Declaration Of Conformity
Declaration of Conformity 1000356V01 DOC - ECOLOG-PRO RBR and 1NTR - Operation Manual_EN | Page 11 / 13... - Page 12 1000356V01 DOC - ECOLOG-PRO RBR and 1NTR - Operation Manual_EN | Page 12 / 13...
- Page 13 ELPRO-BUCHS AG Langäulistrasse 45 9470 Buchs SWITZERLAND E-Mail: swiss@elpro.com For local agencies see: www.elpro.com 1000356V01 DOC - ECOLOG-PRO RBR and 1NTR - Operation Manual_EN | Page 13 / 13...
Need help?
Do you have a question about the ECOLOG-PRO Series and is the answer not in the manual?
Questions and answers