IMPORTANT SAFETY INSTRUCTIONS FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: Save these Instructions for the Local Electrical Inspectors use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. Take care when using cleaning agents or detergents.
Page 5
settings. B. Always turn hood ON when cooking at high heat or when fl ambeing foods ( i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè ). C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or fi lter. D.
Page 6
through the fl ue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
Top Cover Front Panel TYPE Junction Box Light Bulbs Decorative Mesh Filters DESCRIPTION 1/8" x 1/4" 1/8" x 2/4" 1/4" x 2-3/4" - 7 - Electrical Control N° 1 + 1...
NOTE! The device in this version (with internal suction motor) is equipped for rear discharge of exhaust air. However, if required, it is possible to have the exhaust air discharged from the top. This can be accomplished by following the steps indicated in the following paragraphs;...
Page 11
6. Remove the 6” round metal knockout pla- te from the blower plate by using a fl at head screwdriver. See. Fig.4 7. Remove the (10 ) screws securing the blo- wer plate to the blower housing and remo- ve blower plate. See. Fig.5 (Note! If air is discharged from the top, do not rotate the plate;...
Page 12
13. Secure Green/Yellow ground wire connected to the cable to the provided capacitor to blower plate. (type A) Fig. 11 14. Attach the 6 pin male molex connector from blower wire to the 6 pin female molex connector located inside the blower housing. See Fig.12 15.
NOTE! The device in this version (with external motor) is equipped for rear discharge of exhaust air. However, if required, it is possible to have the exhaust air discharged from the top. This can be accomplished by carrying out the steps indicated in the follow- ing paragraphs;...
Page 14
5. Close the front panel while holding it by its external sides until it shuts. 6. Remove the metal motor plate by striking it with the aid of a slotted screwdriver. Fig. 4 7 . Remove the (10) screws securing the blo- wer plate to the blower housing and re- move blower plate.
Page 15
Note: Carry out the power supplly con- nection in accordance with the national electric code, ANSI/NFPA 70-1999. Note1: A cable lock (not included) may be required by local codes. Please review lo- cal codes for more information. 12. Attach 6 pin male molex connectors to 6 pin female molex connectors inside blo- wer housing.
www.zephyronline.com WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating op- tion. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certif ed Silver Tape or Duct Tape.
MOUNTING HEIGHTS The range hood must be installed at a minimum height of 22 inches (56 cm) from the cooking surface. If a connecting duct work composed of two parts is used, the upper part must be placed outside the lower part. Do not connect the range hood duct to the same duct used to exhaust hot air or fumes from another appliance.
Page 18
WARNING: In order to facilitate their connection, make sure that the power supply conduits are not obstructed by the hood. 3. When the hood has been adjusted tighten the screws to secure the hood in place. 4. Once the adjustment has been completed, fi x the hood defi nitely using another (2 type D) screws.
GENERAL • Carefully read the following important information regarding installation safety and maintenance. Keep this information booklet accessible for further consultations. POWER SUPPLY CONNECTION For connection to the power supply refer to the following: 1. Remove the power supply cover by undoing the (2) screws Fig.
www.zephyronline.com MAINTENANCE • It is recommended to operate the appliance prior to cooking. It is recommended to leave the appliance in operation for 5 minutes after cooking is completed in order to completely eliminate cooking vapors and odors. The proper function of the range hood is conditioned by the regularity of maintenance.
DESCRIPTION REPLACEMENT PARTS Light Bulb GU5, 20W (each) OPTIONAL ACCESSORIES Recirculating Kit Replacement Charcoal Filters Short Duct Cover (8”-9” ceiling) Long Duct Cover (9”-10” ceiling) To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368 HOOD Z0B0031 ZRC-00HZ Z0F-00AC Z1C-00TI...