Related Manuals for Zephyr AK11005
Summary of Contents for Zephyr AK11005
- Page 1 Breeze I AK1124x, AK1100x, AK1136x Breeze II AK1200x, AK1236x Model number: Serial Number: Date of Purchase: Sales Dealer: FEB08.0201 © Zephyr Corporation READ AND SAVE THESE INSTRUCTIONS...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE LIST OF MATERIALS INSTALLATION Ducting Calculation Sheet Mounting Height & Clearance Ducting Options Specifi cations Preparing Electrical Preparing Electrical and Ducting Converting to Air Recirculating Mode Mounting the Range Hood ... 13 FEATURES & CONTROLS Controls & Features MAINTENANCE Cleaning and Filter Removal Lights...
- Page 4 READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
-
Page 5: Operation
WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and fi... -
Page 6: Hardware Package Contents
www.zephyronline.com MODELS: BREEZE I AND BREEZE II PARTS SUPPLIED 1 - Hood 2 - Metal Mesh Filters 2 - Incandescent Light Bulbs (R16 40W) 1 - 3-1/4”x10” Rectangular starting collar with damper 1 - Hardware package HARDWARE PACKAGE CONTENTS M4 x 2” (4) M4 x 1-1/2”... - Page 7 Equivalent number Duct pieces length x used 3-1/ 4” x 10” 1 Ft. Rect., straight 6” Round, 1 Ft. straight 7”-10” Round, 1 Ft. straight 3-1/ 4” x 10” 15 Ft. Rect.90 elbow 3-1/ 4” x 10” 9 Ft. Rect.45 elbow 3-1/ 4”...
- Page 8 5-1/2” Min 24” - Max 32" 96" 36" DUCTING A minimum 3-1/4” x 10” rectangular duct must be used to maintain maximum air fl ow effi ciency. Always use rigid type metal ducts only. Flexible ducts could restrict air fl ow by up to 50%. Also use calculation (on page 5) to compute total available duct run when using elbows, transitions and caps.
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Duct Tape. Some Ducting Options Roof Pitch w/ Flashing &...
- Page 10 Air Recirculating Louver Plate BACK 9-1/16” elec. 10” www.zephyronline.com 35-3/4” (36”) 29-3/4” (30”) 23-3/4” (24”) 33-7/8” (36”) 27-7/8” (30”) 22-1/16” (24”) 9-1/16” elec. 10” 10-7/8” 33-5/8” (36”) 27-5/8” (30”) 21-5/8” (24”) SIDE 14-3/8”...
- Page 11 ELECTRICAL WARNING All Electrical work must by performed by qualifi ed electrician or person with similar technical know how and background. For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances.
- Page 12 1. Remove filters 3. If using a cable lock, pry open the desired electrical knockout either on top or back of hood. Feed the wires through the cable lock. Some local codes require the use of a cable lock, check your local codes. 5.
- Page 13 The following instructions are for Breeze hoods beginning with serial number prefi x 13 and later. NOTE: Skip the recirculating preparation pages if you are ducting the air out of your home. An air recirculating kit (optional) must be purchased before using hood in recirculat- ing mode.
- Page 14 www.zephyronline.com NOTE: Skip this page if you are ducting the air out of your home. 5. Remove each of the 5 screws holding 6. Remove (2) interior recirculating panels. the (2) interior recirculating panels. 7. Place louvered recirculating plate over top opening and secure using the screws previously removed.
- Page 15 For Mounting Under a Kitchen Cabinet (Fig 1) 1. Select preferred duct location (vertical or horizontal). 2. Begin installation by removing the fi lters (if installed). 3. Reinforce cabinet with 1”x2” wood strips if additional strengthening is required or if cabinets are framed. 4.
- Page 16 Breeze I, AK11xx This switch turns the blower on and off and controls the speed selection. is off, is low speed, is medium speed and Lights Off/Bright/Dim is off, is bright, is dim. Breeze II, AK12xx This button turns the motors on and off. It also shuts off power to the whole hood. If the lights are on and this button is pushed, they will also turn off.
-
Page 17: Surface Maintenance
SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier soil use liquid degreaser. After cleaning, you may use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain. -
Page 18: Replacing Light Bulbs
Replacement bulbs are available at specialty lighting stores. Purchase type R16 40W incandescent light bulb. A PAR20 50W halogen light bulb may be purchased if you wish to have halogen light bulbs. For Zephyr part numbers please turn to page 18 of the manual. Bottom hood view... - Page 19 TROUBLESHOOTING PROCEDURES FOR BREEZE I AND BREEZE II Issue Cause After installation, 1. The power source is not turned ON. the unit doesn’t work. 2. The power line and the cable locking connector is not connecting properly. 3. The switch board and control board wirings are disconnected.
- Page 20 DESCRIPTION Replacement Parts Light Bulb R16 40W (each) Light Bulb PAR20 50W (each) Metal Filter, 24” hoods (each) Metal Filter, 30” and 36” hoods (each) Optional Accessories Recirculating Kit Replacement Charcoal Filter To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368 www.zephyronline.com PART # Z0B0002 - incandescent bulb included with hood...
- Page 21 Product damaged through negligence, misuse, abuse, accident. Improper installation and failure to follow installation instructions. When product is used commercially or other than its intended purpose. Damaged because of improper connection with equipment of other manufacturers. Repaired or modified by anyone other than Zephyr’s Authorized Agents. What is Not Covered: Consumable parts such as light bulbs, filters, and fuses.