Advertisement
Table of Contents
WARNING:
When building a custom hood for a power pack, always follow all applicable construction codes and standards.
See the illustrations and table below to locate your liner choice and use corresponding custom hood
base dimensions. For the liner installation, only the bottom of the custom hood is needed. Do not
finalize the entire custom hood yet, because an opening is needed for the power pack.
Recommended
thickness:
3/4''
Power Pack
Liner
Model
Model
AK8000AS
AK0800AS
AK0836AS
AK8100AS
AK0806AS
AK8200AS
AK0842AS
AK0848AS
AK0854AS
AK8300ASX
AK0860AS
AK0886AS
AK0882AS
AK8800AG
AK0888AS
AK8800AS
AK0884AS
AK0880AS
*Dimension does not include 3/8" wide flange around liner.
**The inside depth shown in the table above assumes a minimum cabinet backboard thickness of 3/8".
FIG 1:
Zephyr recommends the base of the custom hood to be 3/4" thick plywood. The sides,
front and backboard (if included) of the custom hood to be 3/4" thick, assuming standard
cabinet widths.
Consider the shape and size of the power pack to determine the configuration of the custom hood.
For more details, refer to the installation manual of the power pack.
FEB09.0201
2
1/16'
'
A
Plywood base thickness: 3/4"
FIG 1
Custom Hood
Exterior Width
30 inches
and
36 inches
36 inches
42 inches
48 inches
54 inches
60 inches
36 inches
42 inches
48 inches
and
54 inches
60 inches
Zephyr Corporation
2277 Harbor Bay Pkwy, Alameda, CA 94502
Tel: 1.888.880.8368
e-mail: productsupport@zephyronline.com
AK08xxAS Adjustable Depth Liners
B
*Inside
Width (A)
Without Backboard
28
"
1/2
17
" - 20
1/2
34
"
1/2
34
"
1/2
20
" - 23
1/2
40
"
1/2
46
"
1/2
52
"
1/2
20
" - 23
1/2
58
"
1/2
34
"
1/2
40
"
1/2
20
" - 23
46
"
1/2
1/2
52
"
1/2
58
"
1/2
Fax: 1.888.990.8368
1
*Inside Depth (B)
**With Backboard
"
17
" - 20
1/2
1/8
"
20
" - 23
1/2
1/8
"
20
" - 23
1/2
1/8
"
20
" - 23
1/2
1/8
www.zephyronline.com
"
1/8
"
1/8
"
1/8
"
1/8
Advertisement
Table of Contents
Related Manuals for Zephyr Adjustable Depth Liners AK088xAS
Summary of Contents for Zephyr Adjustable Depth Liners AK088xAS
- Page 1 **The inside depth shown in the table above assumes a minimum cabinet backboard thickness of 3/8”. FIG 1: Zephyr recommends the base of the custom hood to be 3/4” thick plywood. The sides, front and backboard (if included) of the custom hood to be 3/4” thick, assuming standard cabinet widths.
- Page 2 CAUTION: Before installing, remove any protective film from all parts. The custom hood liner must be installed before the power pack unit. For installation into shallow cabinets (20- ” to 21- “ inside depth) the power pack must be installed before the liner front panel section.
Need help?
Do you have a question about the Adjustable Depth Liners AK088xAS and is the answer not in the manual?
Questions and answers