Related Manuals for Zenoah LRTZ2610
Summary of Contents for Zenoah LRTZ2610
- Page 1 SRTZ2610 SRTZ2610F LRTZ2610 SRTZ2610/SRTZ2610F/LRTZ2610 848A3393A0 (801) OWNER’S MANUAL SHORT REACH TRIMMER LONG REACH TRIMMER GB-1...
- Page 2 LRTZ2610 25.4 cm APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION GB-2 EC DECLARATION OF COMFORMITY Husqvarna Zenoah Co., Ltd. 1-9, Minamidai, Kawagoe, Saitama, Japan DIRECTIVE 98/37/EC, prEN774 of 5th April 1994. The products referred are : DESIGNATION : SHORT REACH TRIMMERS/LONG REACH TRIMMERS...
-
Page 3: Table Of Contents
5. For safe operation ... 5 6. Set up ... 8 7. Fuel ... 9 8. Operation ... 10 9. Maintenance ... 12 10. Storage ... 14 11. Disposal ... 14 12. Troubleshooting guide ... 15 Replace the worn-out blades. (SRTZ2610F) SRTZ2610/SRTZ2610F/LRTZ2610 (LRTZ2610) GB-3... -
Page 4: Specifications
1734 x 338 x 254 Air-cooled 2-stroke gasoline Zenoah GZ25N 1.2Hp (0.9kW) at 7500min 3000±200min Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil) Walbro Diaphragm type NGK CMR7A Centrifugal clutch, Spiral bevel gear, Cam crank 4. Symbols on... -
Page 5: For Safe Operation
2. Never use the product, a. when the ground is slippery or when you can’t maintain a steady posture. SRTZ2610/SRTZ2610F/LRTZ2610 b. At night, at times of heavy fog, or at any other times when your field of vision might be... - Page 6 If it continues to move even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized ZENOAH servic- ing dealer for repair. USING THE PRODUCT IMPORTANT Cut only materials recommended by the manufacturer.
- Page 7 SRTZ2610/SRTZ2610F/LRTZ2610 HANDLING FUEL 1. The engine of the ZENOAH prod- uct is designed to run on a mixed fuel, which contains highly flam- mable gasoline. Never store cans of fuel or refill the tank of the unit...
-
Page 8: Set Up
SRTZ2610/SRTZ2610F/LRTZ2610 6. Set up MOUNTING ENGINE 1. Push the shaft tube toward the clutch housing and move it by hand to check that the drive shaft is engaged with the gears. 2. Insert the shaft tube into the clutch housing until it bot- toms, and align the positioning holes on the clutch hous- ing and the shaft tube and install the screw. -
Page 9: Fuel
• The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use (JASO FC GRADE OIL or ISO EGC GRADE). -
Page 10: Operation
SRTZ2610/SRTZ2610F/LRTZ2610 8. Operation STARTING ENGINE WARNING The cutting head will start moving upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start moving upon starting of the engine. - Page 11 2. Turn the bolt located on the top of the trimming mecha- nism counter-clockwise to loosen it. 3. Adjust the angle of the blades to the desired angle, and then fix the bolt firmly back into place. SRTZ2610/SRTZ2610F/LRTZ2610 (1) Clamp bolt (2) Trimming mechanism (3) Tighten...
-
Page 12: Maintenance
• If the blades become so worn down that it is no longer possible to eliminate the gap between them, you should contact the authorized ZENOAH servicing dealer from which you purchased your ZENOAH trim- mer to have the blades resharpened or replaced. TRANSMISSION •... - Page 13 ZENOAH. 0.6 - 0.7 mm • REPLACEMENT PLUG IS A NGK CMR7H. SRTZ2610/SRTZ2610F/LRTZ2610 IMPORTANT • Note that using any spark plug other than those des- ignated may result in the engine failing to operate properly or in the engine becoming overheated and damaged.
-
Page 14: Storage
SRTZ2610/SRTZ2610F/LRTZ2610 9. Maintenance INTAKE AIR COOLING VENT WARNING • Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns. -
Page 15: Troubleshooting Guide
(exhaust port) → carbon is built-up air cleaner cylinder fin, fan cover When your unit seems to need further service, please consult with our ZENOAH service shop in your area. Limited warranty Should any failure occur on the product under normal oper-...