Page 1
APPLICABLE SERIAL NUMBERS : 60000101 and up PORTABLE GAS DRILL PERCEUSE PORTATIVE A ESSENCE PERFORADORA PORTÁTIL A GASOLINA EDG2300R AVERTISSEMENT Les échappements du moteur de ce produit contiennent des produits chimiques connus par l’Etat de Californie comme étant responsables de cancers, d’anomalies congénitales et...
English SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
Français SECURITE Les instructions contenues dans les mises en garde de ce mode d’emploi portant le symbole concernent les points critiques qui doivent être pris en considération pour éviter les blessures corporelles graves, c’est pourquoi ces précautions doivent être rigoureusement suivies. ■...
3. Reduction unit 4. Spark plug 5. Muffer 6. Ignition switch 7. Throttle lever 8. Rear grip 9. Starter grip 10. Fuel cap 11. Air cleaner 12. Front grip (when using RedMax/ZENOAH genuine oil) Specifications are subject to change without notice. English...
10. Tapón del depósito de combustible 11. Filtro de aire 12. Empuñadura delantera (Lors de l’utilisation de la véritable huile RedMax/ZENOAH) Ces spécifications peuvent être modifiées sans préavis. (al utilizar el aceite auténtico de RedMax/ZENOAH) Especificaciones sujetas a cambios sin previo aviso.
ENGINE FAMILY : 7KZXS.0254CD ; EM ENGINE DISPLACEMENT : 23cc REFER TO OWNER'S MANUAL FOR MAINTE- NANCE, SPECIFICATIONS AND ADJUSTMENTS. MANUFACTURED: USE JASO FC OR ISO EGC GRADE 50:1 OIL. ZENOAH CO.,LTD. *1: The initial number will be changed every year of manufacturing.
Se fererer au manuel de l'utilisateur pour les specifications d'entretien et les reglages. FABRIQUE PAR: Utilise JASO FC ou ISO EGC 50:1 Huile. ZENOAH CO.,LTD. *1: Le nombre initial changera chaque année de la fabrication. Español 3. Símbolos presentes en la máquina Para el uso y mantenimiento seguro del producto, los símbolos han sido estampados en relieve en la...
English 4. For safe operation ■ IN ORDER TO ENSURE PROPER AND SAFE OPERATION OF YOUR PORTABLE GAS DRILL • Read this Owner/Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury.
Français 4. Consignes de securite ■ AFIN DE GARANTIR UNE UTILISATION CORRECTE ET SÛRE DE VOTRE PERCEUSE PORTATIVE A ESSENCE • Lire ce mode d'emploi attentivement. Assurez- vous d'avoir bien compris le fonctionnement de cet appareil avant de l'utiliser. Si vous ne respectez pas cette précaution, vous risquez de causer des blessures graves.
English 4. For safe operation • Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn leads to accidents and injury. When planning your work schedule, allow plenty of time to perform the work of cutting and allow plenty of time for rest. Limit the amount of time over which the portable gas drill is to be used continuously to somewhere around 30~40 minutes per session, and take 10~20 minutes...
Page 11
Français 4. Consignes de securite normal. • Le manque de sommeil, la fatigue, ou l'épuisement physique réduisent l'attention, ce qui peut provoquer accidents et blessures. Lors de l'élaboration du plan de travail, prévoir suffisamment de temps de repos. Limiter la durée des périodes pendant lesquelles la machine est utilisée sans interruption entre 30 et 40 minutes.
Page 12
English 4. For safe operation there are no sparks or open flames anywhere nearby before refueling. • If any fuel spillage occurs during refueling, always be sure to use a dry rag to wipe any fuel which has been spilled onto the portable gas drill before turning the engine back on again.
Page 13
Français 4. Consignes de securite circonstances. • Avant de refaire le plein de carburant, arrêter d'abord le moteur et vérifier l'absence de flammes ou d'étincelles à proximité. • Si du carburant se renverse pendant le remplissage, veillez à toujours utiliser un chiffon sec pour essuyer le carburant renversé...
Page 14
English 4. For safe operation engine, hold it firmly in place so as to ensure that nor the throttle may not come into contact with any obstacles when the engine starts up. • Never place the throttle into the high speed position when starting the engine.
Page 15
Français 4. Consignes de securite fermement en place afin de veiller à ce qu'aucun obstacle n'entre en contact avec l'accélérateur au démarrage. • Ne jamais mettre la manette de l'accélérateur à fond au démarrage du moteur. • Une fois le moteur en marche, vérifier que le foret s'arrête de tourner lorsque l'accélérateur est remis à...
Page 16
English 4. For safe operation • Keep operation area clear of all persons, particularly small children and pets. • Never touch the spark plug or plug cord while the engine is in operation. Doing so may result in being subjected to an electrical shock. •...
Page 17
Français 4. Consignes de securite manière ou d'une autre, arrêter le moteur avant de se tourner vers la personne. • Eloigner les personnes de la zone de travail, surtout les enfants et les animaux. • Ne jamais toucher la bougie ou le câble de la bougie lorsque le moteur est en marche.
English 5. Set up 1. Assemble the front grip witch is supplied with the unit to the gear case. 2. Screw the chuck unit into the drive shaft (clockwise). (1) Front grip (2) Chuck unit 3. Insert the drill bit to be used after opening the chuck by the chuck handle and tighten the chuck by the handle.
Français 5. Assemblage 1. Monter le levier qui est fourni avec l’unité sur la boîte d’engrenages. 2. Visser l’ensemble du mandrin dans l’arbre d’entraînement (dans le sens des aiguilles d’une montre). (1) Levier (2) Mandrin 3. Insérer le trépan devant être utilisé après avoir ouvert le mandrin par l’intermédiaire du levier du mandrin et serrer le mandrin au myen du levier.
2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE) • Do not use BIA or TCW (2-stroke water-cooling type) mixed oil. ■ RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 (when using RedMax/ZENOAH genuine oil) 50:1 MIXING CHART GASOLINE gal. 2-CYCLE OIL fl.oz...
(pour les moteurs 2 temps à refroidissement par eau). ■ RAPPORT DE MELANGE RECOMMANDE ESSENCE 50 : HUILE 1 (Lors de l’utilisation de la véritable huile RedMax/ZENOAH) TABLEAU DE MELANGE 50 :1 ESSENCE gal. HUILE 2 TEMPS once liquide ESSENCE...
English 6. Fuel ■ HOW TO MIX FUEL IMPORTANT Agitate carefully. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. 3. Pour in all of the oil and agitate well. 4.
Page 23
Français 6. Carburant participer ainsi à la protection de l’environnement et de votre santé. • De l’essence ou de l’huile de basse qualité risque d’endommager les joints, les conduites d’essence ou le réservoir d’essence du moteur. ■ COMMENT OBTENIR UN BON MELANGE IMPORTANT Agiter avec précautions.
Page 24
English 6. Fuel cause severe damage to the internal engine parts very quickly. 2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication. 3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.
Page 25
Français 6. Carburant 1. ESSENCE SANS HUILE (ESSENCE PURE) – L’essence pure est capable d’endommager très rapidement les pièces du moteur. 2. ESSENCE-ALCOOL – Ce mélange risque de très rapidement détruire les pièces en caoutchouc et/ou en plastique et d’empêcher la lubrification du moteur.
.04 or .08 in. (1~2mm) English 7. Operation ■ THROTTLE CABLE ADJUSTMENT Check the throttle cable play and adjust to .04 or .08 in. (1~2mm) at the carburetor side. (1) Throttle cable (3) Lock nut ■ STARTING ENGINE 1. Set ignition switch to "RUN" position. (OP2) (1) Ignition switch (A) RUN 2.
Français 7. Fonctionnement ■ REGLAGE DU CABLE D'ACCELERATION Vérifier le jeu du câble d'accélération et le régler à 1 ou 2mm du côté du carburateur. (1) Câble d'accélération (2) Vis de réglage (3) Ecrou de verrouillage ■ MISE EN MARCHE DU MOTEUR 1.
English 7. Operation ■ STOPPING ENGINE • Gradually decrease the engine speed to an idle speed, and then slide ignition switch to "STOP" position. (1) Ignition switch (A) RUN (B) STOP ■ BORING OPERATION (OP6, OP7) • Keep the engine running at full throttle during operation.
Page 29
Français 7. Fonctionnement ■ ARRET DU MOTEUR • Réduire peu à peu la vitesse du moteur jusqu’au ralenti, puis placer le bouton de contact en position "STOP" (arrêt). (1) Bouton de contact (A) MARCHE (B) ARRÊT ■ PERCAGE (OP6, OP7) •...
Page 30
OP10 OP11 English 7. Operation ■ ADJUSTMENT OF IDLING SPEED • The engine idling speed is preadjusted at the factory so that the engine keeps running without moving the drill when releasing the throttle lever to the idling position. However, due to changes in engine conditions, it may be necessary to adjust the idling.
Page 31
Français 7. Fonctionnement ■ REGLAGE DE LA VITESSE DU RALENTI • La vitesse du ralenti du moteur est préréglée à l'usine afin que le moteur continue de fonctionner sans que le foret tourne lorsque le levier d'accélération est relâché en position de ralenti. Cependant, à...
8. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. ■ MAINTENANCE CHART system/compornent fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug cylinder fins, intake air cooling vent muffler, spark arrester, cylinder exhaust port clean...
8. Entretien L’entretien, le remplacement ou la réparation du dispositif et des systèmes de lutte contre les émissions peuvent être effectués par toute société ou individu spécialisé dans la réparation des moteurs hors-route. ■ TABLEAU D’ENTRETIEN Système/Composant fuites ou éclaboussures de carburant réservoir de carburant, filtre à...
.024 ~ .028 in (0.6~0.7mm) English 8. Maintenance WARNING Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Disconnect the spark plug terminal to avoid accidental engine starts. ■ DAILY INSPECTION • Remove grass or dust, from the entire body. •...
Page 35
Français 8. Entretien AVERTISSEMENT Avant de nettoyer, inspecter ou réparer votre appareil, assurez-vous que le moteur est arrêté et refroidi. Débrancher la borne de la bougie pour éviter un démarrage accidentel du moteur. ■ INSPECTION QUOTIDIENNE • Ôter l'herbe et la poussière du corps de l'appareil. •...
English 8. Maintenance • Check and tighten each fastener. • Dismount the engine and check the clutch system to see if oil is observed between the clutch lining and its drum. If any, wipe it off with gasoline. Cleaning the cylinder fins •...
Français 8. Entretien • Contrôler et serrer toutes les attaches. • Démonter le moteur et vérifier le système d'embrayage et son barillet pour voir si de l'huile se trouve entre la garniture de l'embrayage et son barillet. S'il se trouve de l'huile, l'essuyer avec de l'essence.
11. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw sparking (no spark) spark plug Case 2. Engine starts but does not keep running/Hard re-starting. CHECK fuel tank carburetor adjustment screw muffler,cylinder (exhaust port) air cleaner cylinder fin, fan cover When your unit seems to need further service, please consult with our service shop in your area.
12. Lista de piezas NOTE : 1. Use RedMax/ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. RedMax/ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified company.
Page 40
12. Parts list Fig.1 GEAR CASE, HANDLE, TOOLS EDG2300R (S/N 60000101 and up)
Page 41
Fig.1 GEAR CASE, HANDLE, TOOLS EDG2300R (S/N 60000101 and up) KEY# PART NUMBER DESCRIPTION 1 TA0023214120 GEAR CASE A 2 TA0063210A80 GEAR CASE B COMP. 3 TA0893214180 SHIFT FORK COMP. 4 TA1063214120 SHIFT GUIDE SPRING 5 TA1083214120 SHIFT LEVER 6 TA3003225080 GREASE NIPPLE COMP.
Page 42
12. Parts list Fig.2 ENGINE UNIT EDG2300R (S/N 60000101 and up)
Page 43
Fig.2 ENGINE UNIT EDG2300R (S/N 60000101 and up) Key# Part Number Description 5602-12110 CYLINDER 5500-12213 GASKET, base 1850-12130 BOLT M5x12 5500-13163 INSULATOR 5500-13121 GASKET, INSULATOR 5500-13131 GASKET, CARB 0263-90520 SCREW M5x20 5602-15100 MUFFLER ASSY 1601-15120 • ARRESTER 01252-30550 BOLT M5x55...
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, RedMax / ZENOAH AMERICA, INC., THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
Cette garantie vous donne des droits juridiques spécifiques, et vous pouvez également jouir d’autres droits variant d'une province à l'autre. Si vous désirez obtenir des informations sur le centre de service le plus proche, veuillez appeler RedMax / ZENOAH AMERICA, INC. au (770)-381-5147 Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat.
ZENOAH AMERICA, INC. LLAMANDO AL (770)-381-5147. IMPORTANTE: RECIBIRÁ UNA TARJETA DE REGISTRO DE GARANTÍA EN EL MOMENTO DE LA COMPRA. LLENE LA TARJETA Y ENVÍELA A RedMax / ZENOAH AMERICA DENTRO DE SIETE (7) DÍAS. ASEGÚRESE DE CONSERVAR UNA COPIA PARA SUS REGISTROS.
Page 48
ZENOAH AMERICA, INC. 1100 Laval Blvd. Suite 110 Lawrenceville, Georgia 30043...
Need help?
Do you have a question about the EDG2300R and is the answer not in the manual?
Questions and answers